Sony DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) Service Manual ▷ View online
1-1
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. TO TAKE OUT A DISC WHEN NOT EJECT (FORCE EJECT)
1
Remove the screw (M1.7).
2
Remove the eject cabinet.
3
Insert the wire etc. in the hole and down the lever by it.
1-3. PRECAUTION ON REPLACING THE VC-521 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
Eject Cabinet
Screw (M1.7)
Hole
Lever
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1 1
3 1
C
Repaired by:
Refer to “1-4-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD screen
C : 3 1 : 1 1
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder or LCD
screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1-4-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
6
1
6
1
6
2
6
2
6
2
6
2
6
2
6
2
6
2
6
2
9
1
9
4
9
4
Detailed
Code
0
0
0
1
0
2
6
0
0
0
0
0
1
0
1
1
0
0
0
1
0
2
0
3
1
0
1
1
1
2
2
0
0
1
0
0
0
1
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Disc access error
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Flash memory data are rewritten.
Drive fault
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller
communication abnormality among.
communication abnormality among.
Shift lens initializing failure.
Shift lens overheating (Pitch).
Shift lens overheating (Yaw).
Abnormality of thermistor.
Abnormality when flash is being charged.
Fault of writing to or erasing the flash
memory
memory
Internal flash memory fault
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Use a compatible disc with the camcorder.
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin qh, qj of
CN5101 on the LD-233 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-233 board).
recover, check the focus MR sensor of lens block (pin qh, qj of
CN5101 on the LD-233 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-233 board).
Make flash memory data correct value. (Note 1)
Inspect or replacement of the mechanism deck, IC (IC4401 on
the VC-521 board) and drive block.
the VC-521 board) and drive block.
Inspect the lens block zoom MR sensor (pin ql, wa of CN5101
on the LD-233 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5201 on the LD-233 board) when zooming is not performed.
on the LD-233 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5201 on the LD-233 board) when zooming is not performed.
Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE6501 on the FR-283
board) peripheral circuits.
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE6502 on the FR-283
board) peripheral circuits.
board) peripheral circuits.
Refer to [1-5-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred].
Occurred].
Inspect the steadyshot circuit (IC5501 on the LD-233 board).
Replacement of lens block. If an error occurs again, replace the
LD-233 board. (Note 2)
LD-233 board. (Note 2)
Refer to [1-5-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Occurred].
Occurred].
Refer to [1-5-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Occurred].
Occurred].
Refer to [1-5-4. E : 62 : 20 (Abnormality of Thermistor)
Occurred].
Occurred].
Checking of flash unit or replacement of flash unit.
Inspect the flash memory (IC2101 on the VC-521 board).
Inspect the internal flash memory (MDL4060S3C). (HDR-UX19E/
UX20/UX20E only)
UX20/UX20E only)
Note 1:
Refer to Service manual, ADJ (“1-3. DESTINATION DATA WRITE”).
Note 2:
When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1-5. METHOD OF COPING WITH SHIFT LENS ERROR
about 330 msec
Fig. 1
Measurement points on the LD-233 board
IC5501
LD-233 BOARD
R5526
R5534
R5549
R5549: No Mount
(Short Land)
Fig. 2
Change in output voltage of R5549 on the LD-233 board
Note: The length of low section will vary a little depending on the
conditions.
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501 on the LD-233 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1301 of VC-521 board) periphery.
the camera control circuit (IC1301 of VC-521 board) periphery.
Note:
When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
IC1301
VC-521 BOARD (SIDE A)
Fig. 3
Measurement points on the VC-521 board
Ver. 1.1 2008.02
Click on the first or last page to see other DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) service manuals if exist.