Sony DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man4) Service Manual ▷ View online
6-86
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
3-2.
ADJUSTMENT REMOTE COMMANDER
(NEW LANC JIG)
(NEW LANC JIG)
The adjustment remote commander (New LANC Jig) is used for
changing the calculation coefficient in signal processing, EVR data,
etc. The adjustment remote commander (New LANC Jig) performs
bi-directional communication with the unit using the remote com-
mander signal line (LANC). The resultant data of this bi-direc-
tional communication is written in the non-volatile memory.
changing the calculation coefficient in signal processing, EVR data,
etc. The adjustment remote commander (New LANC Jig) performs
bi-directional communication with the unit using the remote com-
mander signal line (LANC). The resultant data of this bi-direc-
tional communication is written in the non-volatile memory.
1.
Using the Adjustment Remote Commander
(New LANC Jig))
(New LANC Jig))
1) Connect the adjustment remote commander (New LANC Jig)
to the LANC terminal via the LANC cable (J-6082-442-A).
2) Set the slide switch of the adjustment remote commander (New
LANC Jig) to “SERVICE” (SERVICE position). If it has been
properly connected, the LCD on the adjustment remote com-
mander (New LANC Jig) will display as shown in Fig. 6-3-2.
properly connected, the LCD on the adjustment remote com-
mander (New LANC Jig) will display as shown in Fig. 6-3-2.
Fig. 6-3-2
3) Operate the adjustment remote commander (New LANC Jig)
as follows.
• Changing the page
• Changing the page
The page increases when the Page+ (M) button is pressed,
and decreases when the Page- (m) button is pressed.
and decreases when the Page- (m) button is pressed.
• Changing the address
The address increases when the ADD+ (N) button is
pressed, and decreases when the ADD
pressed, and decreases when the ADD
− (X) button is
pressed. There are altogether 256 addresses, from 00 to FF.
• Changing the data (Data setting)
The data increases when the Data+ button is pressed, and
decreases when the Data
decreases when the Data
− button is pressed. There are alto-
gether 256 data, from 00 to FF.
• Writing the adjustment data
The Write (x) button must be pressed to write the adjust-
ment data in the nonvolatile memory. (The new adjusting
data will not be recorded in the nonvolatile memory if this
step is not performed)
ment data in the nonvolatile memory. (The new adjusting
data will not be recorded in the nonvolatile memory if this
step is not performed)
4) After completing all adjustments, turn off the main power sup-
ply (8.4 V) once.
2. Precautions Upon Using
the Adjustment Remote Commander (New LANC Jig)
Mishandling of the adjustment remote commander (New LANC
Jig) may erase the correct adjustment data at times. To prevent
this, it is recommended that all adjustment data be noted down
before beginning adjustments and new adjustment data after each
adjustment.
Jig) may erase the correct adjustment data at times. To prevent
this, it is recommended that all adjustment data be noted down
before beginning adjustments and new adjustment data after each
adjustment.
Page
Address
Data
p:00 a:00 d:00
6-87
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
3-3.
APPLICATION FOR ADJUSTMENT
(SeusCam)
(SeusCam)
The adjustment software (SeusCam) can change operational coef-
ficients of signal processing, EVR data, etc. same as the adjust-
ment remote commander. The SeusCam performs two-way com-
munication between PC and camcoder using the USB terminal.
The two-way communication result data can be written in the non-
volatile memory.
ficients of signal processing, EVR data, etc. same as the adjust-
ment remote commander. The SeusCam performs two-way com-
munication between PC and camcoder using the USB terminal.
The two-way communication result data can be written in the non-
volatile memory.
Note 1:
The SeusCam is used exclusively for the camcoders
(DCR, DHR, CCD, etc.). It cannot be used for digital
cameras (DSC, MVC, etc.).
(DCR, DHR, CCD, etc.). It cannot be used for digital
cameras (DSC, MVC, etc.).
Note 2:
Before using the SeusCam, set the following data using
the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press
the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press
the PAUSE (Write) button.
After use, release the set data.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 00, and press
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 00, and press
the PAUSE (Write) button.
3) Select page: 0, address: 01, and set data: 00.
1.
Connection
1) Connect the HASP key to the USB terminal of the PC.
2) Connect the PC and camcoder with the USB cable.
3) Start the SeusCam on the PC.
4) Click [Connect] on the SeusCam screen. If the connection is
2) Connect the PC and camcoder with the USB cable.
3) Start the SeusCam on the PC.
4) Click [Connect] on the SeusCam screen. If the connection is
normal, the SeusCam screen will be as shown in Fig. 6-3-3,
indicating the “connected” state.
indicating the “connected” state.
Note:
The SeusCam will go in “disconnect” state, if the set is
turned off (for instance, by resetting the set). In such a
case, click [Connect] on the SeusCam screen to restore
the “connected”
turned off (for instance, by resetting the set). In such a
case, click [Connect] on the SeusCam screen to restore
the “connected”
state.
Fig. 6-3-3
2.
Operation
• Page change
To change the page, click [Page] on the SeusCam screen and
enter the page to be changed. The page is displayed in hexa-
decimal notation.
enter the page to be changed. The page is displayed in hexa-
decimal notation.
• Address change
To change the address, click [Address] on the SeusCam screen
and enter the address to be changed. The address is displayed in
hexadecimal notation.
and enter the address to be changed. The address is displayed in
hexadecimal notation.
• Data change
To change the data, click [Set] on the SeusCam screen and enter
the data. The data is displayed in hexadecimal notation.
This operation does not write the data to the nonvolatile memory.
the data. The data is displayed in hexadecimal notation.
This operation does not write the data to the nonvolatile memory.
• Data writing
To write the data to the nonvolatile memory, click [Write] on the
SeusCam screen and enter the data to be written.
SeusCam screen and enter the data to be written.
• Data reading
The data displayed on the SeusCam screen are the data values
at the time when the pages and addresses were set, and they are
not updated automatically. To check the data change, click [Read]
on the SeusCam screen and update the displayed data.
at the time when the pages and addresses were set, and they are
not updated automatically. To check the data change, click [Read]
on the SeusCam screen and update the displayed data.
3.
Difference in Display Between SeusCam and
Adjustment Remote Commander
Adjustment Remote Commander
There is no difference in display of address and data between
SeusCam and adjustment remote commander. Though the page is
displayed in one digit on the adjustment remote commander, it is
displayed in two digits on the SeusCam.
The “page 1A” or “page 1F” is selected after setting data: 01 to
the page: 0, address: 10 on the adjustment remote commander,
while it can be selected by clicking the
SeusCam and adjustment remote commander. Though the page is
displayed in one digit on the adjustment remote commander, it is
displayed in two digits on the SeusCam.
The “page 1A” or “page 1F” is selected after setting data: 01 to
the page: 0, address: 10 on the adjustment remote commander,
while it can be selected by clicking the
[Page]
and entering “1A”
or “1F” on the SeusCam. For the “page A” or “page F”, enter “0A”
or “0F”.
or “0F”.
4.
Precaution on Use of SeusCam
Wrong SeusCam operation could clear correct adjustment data.
To prevent the data clear by mistake, it is recommended to save all
adjustment data by clicking [Page Edit] on the SeusCam screen
before starting the adjustment.
To prevent the data clear by mistake, it is recommended to save all
adjustment data by clicking [Page Edit] on the SeusCam screen
before starting the adjustment.
Saving Method:
1) Click [Page Edit] on the SeusCam screen to display the SeusCam
1) Click [Page Edit] on the SeusCam screen to display the SeusCam
Page Edit screen.
2) Click [Page], and enter the page number to be saved.
3) Click [Read] to read the data to be saved from the camera.
4) Click [File] and save the data to PC.
3) Click [Read] to read the data to be saved from the camera.
4) Click [File] and save the data to PC.
Loading Method:
1) Select page: 00, address: 01 and set data: 01.
2) Click [Page Edit] on the SeusCam screen to display the SeusCam
1) Select page: 00, address: 01 and set data: 01.
2) Click [Page Edit] on the SeusCam screen to display the SeusCam
Page Edit screen.
3) Click [File] and load the data from PC.
4) Click [Write] on the SeusCam Page Edit screen.
4) Click [Write] on the SeusCam Page Edit screen.
6-88
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
Hexadecimal-decimal Conversion Table
Lower digit of
hexadecimal
Upper digit
of hexadecimal
of hexadecimal
0
1
2
3
4
5
6
7
8
9
A
(
A
)
B
(
b
)
C
(
c
)
D
(
d
)
E
(
E
)
F
(
F
)
0
1
2
3
4
5
6
7
8
9
A (
A
)
B (
b
)
C (
c
)
D (
d
)
E (
E
)
F (
F
)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
77
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
174
159
175
160
161
162
163
164
165
166
167
168
169
170
171
172
173
177
176
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
0
1
Note:
The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander.
(Example)
If the DDS display or the adjustment remote commander shows BD (
bd
);
Because the upper digit of the adjustment number is B (
b
), and the lower digit is D (
d
), the meeting point
“189” of 1 and 2 in the above table is the corresponding decimal number.
0
2
3-4.
DATA PROCESS
The calculation of the DDS display and the adjustment remote
commander display data (hexadecimal notation) are required for
obtaining the adjustment data of some adjustment items. In this
case, after converting the hexadecimal notation to decimal nota-
tion, calculate and convert the result to hexadecimal notation, and
use it as the adjustment data. Indicates the hexadecimal-decimal
conversion table.
commander display data (hexadecimal notation) are required for
obtaining the adjustment data of some adjustment items. In this
case, after converting the hexadecimal notation to decimal nota-
tion, calculate and convert the result to hexadecimal notation, and
use it as the adjustment data. Indicates the hexadecimal-decimal
conversion table.
Table 6-3-1
6-89
DCR-DVD505/DVD505E/DVD905/DVD905E_ADJ
2.
Emergence Memory Address
2-1. Emergency Memory Address (Camera section)
Page 6B
Address 14 to 17
Note:
If reading/writing data on pages 6B, set data: 06 to page:
0, address: 10, and then select pages: B. By this data set-
ting, the pages 6B can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
0, address: 10, and then select pages: B. By this data set-
ting, the pages 6B can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
Address
Contents
14
EMG code when first error occurs
15
EMG code when second error occurs
16
EMG code when third error occurs
17
EMG code when last error occurs
When no error occurs in this unit, data “00” is written in the above
addresses (14 to 17). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (14). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (15).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (17).
addresses (14 to 17). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (14). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (15).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (17).
Note:
After completing adjustments, be sure to initialize the data
of addresses 14 to 17 to “00”.
of addresses 14 to 17 to “00”.
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
6
01
FD
Press PAUSE (Write) button.
3
6
02
Check the data changes to
“01”.
“01”.
4
6
01
00
Press PAUSE (Write) button.
5
0
01
00
2-2. EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in 6B
page, addresses 14 to 17. The type of error indicated by the code
are shown in the following table.
page, addresses 14 to 17. The type of error indicated by the code
are shown in the following table.
Code
Emergency Type
00
No error
3-5.
SERVICE MODE
Note:
Before performing the adjustment, check the data of page:
0, address: 10 is “00”. If not, select page: 0, address: 00,
and set data “00”.
0, address: 10 is “00”. If not, select page: 0, address: 00,
and set data “00”.
1.
Setting the Test Mode
Page A
Address 10
Data
Function
00
Normal
01
Forced MOVIE mode
02
Forced PLAY/EDIT mode
05
Forced STILL mode
06
Forced LINE INPUT mode
• Before setting the data , select page: 0, address: 01, and set data:
01.
• For page A, the data set will be recorded in the non-volatile
memory by pressing the PAUSE (Write) button of the adjust-
ment remote commander. In this case, take note that the test
mode will not be exited even when the main power is turned off
(8.4 Vdc).
ment remote commander. In this case, take note that the test
mode will not be exited even when the main power is turned off
(8.4 Vdc).
• After completing adjustments/repairs, be sure to return the data
of this address to 00, and press the PAUSE (Write) button of the
adjustment remote commander. And select page: 0, address: 01,
and set data: 00.
adjustment remote commander. And select page: 0, address: 01,
and set data: 00.
Click on the first or last page to see other DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man4) service manuals if exist.