DOWNLOAD Sony DCR-DVD505 / DCR-DVD505E / DCR-DVD905 / DCR-DVD905E (serv.man2) Service Manual ↓ Size: 11.28 MB | Pages: 83 in PDF or view online for FREE

1-2

DCR-DVD505/DVD505E/DVD905/DVD905E_L2

DVD mechanism deck

MD-129 board (side A)

VC-439 board (side B)

Flexible board (10P)

Extension cable (10P)

(J-6082-572-A)

Extension cable (100P)

(J-6082-578-A)

CN3909

CN3902

CN1007

1. Connect the extension cable (J-6082-572-A) between the DVD mechanism deck and CN3909 on the MD-129 board.
2. Connect the extension cable (J-6082-578-A) between CN3902 on the MD-129 board and CN1007 on the VC-439 board.

When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.

When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.

1 1

3 1

C

Repaired by:

Refer to “1-5-3. Self-diagnosis Code Table”.

Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2Hz

C : Corrected by customer
H : Corrected by dealer
E : Corrected by service

engineer

Viewfinder or LCD screen

C : 3 1 : 1 1

1-3

DCR-DVD505/DVD505E/DVD905/DVD905E_L2

C

C

C

C

C

C

E

E

E

E

E

E

E

E

E

E

E

Block

Function

0

4

1

3

1

3

2

1

3

2

3

2

2

0

3

1

4

0

4

0

6

1

6

1

6

2

6

2

9

1

9

4

9

4

Detailed

Code

0

0

0

0

0

2

0

0

5

0

6

0

0

0

0

0

0

0

0

1

1

0

1

1

0

0

0

1

0

1

0

0

0

1

-

Symptom/State

Non-standard battery is used.

Faulty disc is used.

Disc access error

Condensation.

Codec IC dose not return any reply

Difficult to adjust focus
(Cannot initialize focus)

EEPROM data are rewritten.

Drive fault

Codec IC fault

Audio Codec IC fault

Zoom operations fault
(Cannot initialize zoom lens.)

The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.

Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)

Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)

Abnormality when flash is being charged.

Fault of writing to or erasing the
flashmemory

Fault of writing to or erasing EEPROM

Self-diagnosis Code

Repaired b

y:

Correction

Use the InfoLITHIUM battery.

Use a compatible disc with the camcorder.

Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.

Remove the disc, and insert it again after one hour.

Remove the power source. Reconnect it again and operate your
camcorder again

Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin ql, wa of
CN2101 on the VC-439 board). If it is OK, check the focus
motor drive IC (IC2104 on the VC-439 board).

Make EEPROM data correct value. (Note 1)

Inspect or replacement of the mechanism deck, IC (IC4301 on
the MD-129 board) and drive block

Inspect or replacement of the codec IC (IC3001on the VC-439
board) peripheral circuits

Inspect or replacement of the Audio Codec IC (IC3001 on the
VC-439 board) peripheral circuits

Inspect the lens block zoom MR sensor (pin qh, qk of CN2101
on the VC-439 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC2104 on the VC-439 board) when zooming is not performed.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

Inspect PITCH angular velocity sensors (SE6801 on the CM-069
board) peripheral circuits.

Inspect YAW angular velocity sensors (SE6802 on the CM-069
board) peripheral circuits.

Checking of flash unit or replacement of flash unit. (Note 2)

Inspect the flash memory (IC3101 on the VC-439 board). (Note 1)

Inspect the EEPROM (IC2602 on the VC-439 board). (Note 1)

Refer to “10-2. Record of Self-diagnosis check” of “3-5. SERVICE MODE”, ADJ (9-876-938-51).

After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.

1-4

DCR-DVD505/DVD505E/DVD905/DVD905E_L2

When “FLASH error” (Self-diagnosis Code E:91:**) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is
changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Connect the adjustment remote commander and perform the following process.

Order Page Address Data

Procedure

1

7

01

75

2

7

00

01

Press PAUSE button.

3

7

02

Check the data changes to “01”.

When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right value.

Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.

 To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.

3) Select page: 0, address: 01, and set data: 00.

Page

A

A

A

A

Data

DCR-DVD505

35

30

35

00

DCR-DVD905

39

30

35

00

DCR-DVD505E

35

30

35

45

Address

B7

B8

B9

BA

DCR-DVD905E

39

30

35

45

1-5

DCR-DVD505/DVD505E/DVD905/DVD905E_L2

1-2. イジェクトしない時のディスク取出し方法（強制イジェクト）

1

ねじ（M1.7）とフロントカバー（198）を外す。

2

穴に針金等を差し込み，イジェクトスライダを下げる。

1-3. 強制電源ONモードの設定

調整リモコン（RM-95またはNEW LANC JIG）を使用して，電源を入れることが出来ます。

カムコーダの操作は調整リモコンで行えます。

1-3-1. 強制Movie電源ONモードの設定

1) ページ：0，アドレス：01にデータ：01をセット。

2) ページ：A，アドレス：10にデータ：01をセットしPAUSE（Write）ボタンを押す。

1-3-2. 強制Play/Edit電源ONモードの設定

1) ページ：0，アドレス：01にデータ：01をセット。

2) ページ：A，アドレス：10にデータ：02をセットしPAUSE（Write）ボタンを押す。

1-3-3. 強制電源ONモードの解除

1) ページ：0，アドレス：01にデータ：01をセット。

2) ページ：A，アドレス：10にデータ：00をセットしPAUSE（Write）ボタンを押す。
3) ページ：0，アドレス：01にデータ：00をセット。

1-1. 修理時の電源供給について

本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。

これを避けるため，下記の方法を用いてください。

方法：
DC入力端子を使用する。（ACアダプタ（AC-L200）を使用する。）