DOWNLOAD Sony DCR-DVD408 (serv.man3) Service Manual ↓ Size: 1.25 MB | Pages: 65 in PDF or view online for FREE

6-38

DCR-DVD408_ADJ

Name

DVD-R Disc
for Self Jitter

DVD-RW
Reference + DOW
Disc

DVD+RDL
Self Disc

Use

Diagnosis and adjustment of DVD-R

Diagnosis and adjustment of DVD-RW

Diagnosis and adjustment of DVD+RDL

Remark

This disc can be used about 78 times (min. 22 times) for the
diagnosis and adjustment. (Note 3)

This disc can be used about 1174 times for the diagnosis and
adjustment. (Note 3)

This disc can be used about 38 times (min. 9 times) for the
diagnosis and adjustment. (Note 3)

Note 3: If the DVD-R Disc for Self Jitter, DVD-RW Reference + DOW Disc and DVD+RDL Self Disc exceeds the use limit, the

following message will be displayed. Replace it with a new disc and click the [OK] button in the message window.
The disc use counts are saved in the PC. Accordingly, the disc and PC used for diagnosis and adjustment must always be
controlled in the same combination.
If the disc is used with another PC, it will be recognized as a new disc, causing the use limit to be unknown.

To diagnose and adjust the drive block, the discs listed in the following table are used.
Note 1: Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT)

If a wrong disc is used, the disc could be destroyed and could not be reused.

Note 2: Handle the disc with care, and before use, check if the disc is scratched or dirty.

6-39

DCR-DVD408_ADJ

Extract the compressed file in the ZIP format. If the extracted file (AUDIT for 2007.msi) is executed, the installer will start. Perform the
installation following the instructions given on the screen of the installer.

Click the [Start] button on the task bar, and from the [Programs], click [AUDIT for Service] – [AUDIT for 2007], and the AUDIT will start. The
SeusEX starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment.
Again, the SeusEX starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusEX cannot start (because, for instance, the HASP key is not connected to the PC), the AUDIT
also does not start.

1. Diagnosis section

2. Adjustment section

3. Comment display section

4. Status display section

6. 

[SET]

 button

7. Menu section

5. 

[STOP]

 button

1.XX

8. Caution display 

section

6-40

DCR-DVD408_ADJ

Use these buttons when diagnosing the drive block.

Use these buttons when adjusting the drive block.

At the execution of diagnosis and adjustment, its progress situa-
tion is displayed.
1) [Clear] button

This button clears the comment in the display section.

2) [LOG] button

This button saves the comment in the display section as a log
file.

The result of diagnosis and adjustment is displayed.

[STOP] button

This button stops the diagnosis and adjustment in the midway.

[SET] button (After completing the TEST)

This button cancels the TEST mode set to the cam coder during
the diagnosis and adjustment. If the TEST mode is cancelled suc-
cessfully, the following message is displayed.
Note: Before exiting the AUDIT, be sure to cancel the TEST mode

by clicking the SET button of “After completing the TEST”.
Unless the TEST mode is cancelled, the drive may not op-
erate normally, such that “disc cover does not open”, “drive
error is displayed”, etc..

1) [RESET] button

This button resets internal register.
(Use this button to interrupt the work so far when diagnosis
and adjustment stopped and no response is returned. The work
terminates with the previous adjustment data written to the
camcoder.)

2) [Lid Open] button

This button opens the disc cover.

At the execution of POWER Adjustment, the caution of POWER
Adjustment is displayed.

[Clear]

 button

[LOG]

 button

6-41

DCR-DVD408_ADJ

Order

Diagnostic item

Message

Disc

Operation

1

No Disc

Click the 

[START]

 button of “DIAGNOSIS”.

2

No Disc

Check the movement of the pickup lens (Focus
direction/Tracking direction), and click the

[OK]

 button in the message window.

3

No Disc

Check the movement of the sled, and click the

[OK]

 button in the message window.

4

No Disc

Check the rotation of the spindle, and click the

[OK]

 button in the message window.

Sensors

All items of diagnosis buttons are executed

in the descending order.

Diagnosis button: Only the diagnostic item assigned to the

button name is executed.

Diagnosis status is displayed with color.
White

Not diagnosed

Red blinking

Diagnosis in progress

Green

Diagnosis OK

Red

Diagnosis NG

START button

Status lamp

Diagnosis buttons