DOWNLOAD Sony DCR-DVD405 (serv.man2) Service Manual ↓ Size: 9.3 MB | Pages: 91 in PDF or view online for FREE

Model
DCR-DVD405 (serv.man2)
Pages
91
Size
9.3 MB
Type
PDF
Document
Service Manual
Brand
Device
Movie / BRAZIL LEVEL 2
File
dcr-dvd405-sm2.pdf
Date

Sony DCR-DVD405 (serv.man2) Service Manual ▷ View online

1-3
DCR-DVD405_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-5-3. Self-diagnosis Code Table
C
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
1
3
2
2
0
3
1
4
0
4
0
6
1
6
1
6
1
6
2
6
2
9
1
9
4
9
4
Detailed
Code
0
0
0
0
0
2
0
0
5
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
1
0
1
0
0
0
1
-
Symptom/State
Non-standard battery is used.
Faulty disc is used.
Disc access error
Condensation.
Codec IC dose not return any reply
EEPROM data are rewritten.
Drive fault
Codec IC fault
Audio Codec IC fault
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality when flash is being charged.
Fault of writing to or erasing the
flashmemory
Fault of writing to or erasing EEPROM
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Use a compatible disc with the camcorder.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Remove the power source. Reconnect it again and operate your
camcorder again
Make EEPROM data correct value. (Note 1)
Inspect or replacement of the mechanism deck, IC (IC4302 on
the MD-128 board) and drive block
Inspect or replacement of the codec IC (IC3001on the VC-427
board) peripheral circuits
Inspect or replacement of the Audio Codec IC (IC3001 on the
VC-427 board) peripheral circuits
Inspect the lens block focus MR sensor (pin ql, wa of CN1701
on the VC-427 board) when focusing is performed when the
focus buttons of the touch panel are pressed in the focus manual
mode, and the focus motor drive circuit (IC1701 on the VC-427
board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (pin qh, qk of CN1701
on the VC-427 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC1701 on the VC-427 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the  flexible board, inspect the focus/zoom motor drive circuit
(IC1701 on the VC-427 board).
Inspect PITCH angular velocity sensors (SE5501 on the FR-245
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE5502 on the FR-245
board) peripheral circuits.
Checking of flash unit or replacement of flash unit. (Note 2)
Inspect the flash memory (IC3101 on the VC-427 board). (Note 1)
Inspect the EEPROM (IC2602 on the VC-427 board). (Note 1)
Note1: Refer to “9-2. Record of Self-diagnosis check” of “3-4. SERVICE MODE”, ADJ (9-876-933-51).
Note2: After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.
1-4
DCR-DVD405_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-6. PROCESS
O APÓS FIXADO ERRO DO FLASH
When “FLASH error” (Self-diagnosis Code E:91:**) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is
changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Connect the adjustment remote commander and perform the following process.
Order Page Address Data
Procedure
1
7
01
75
2
7
00
01
Press PAUSE button.
3
7
02
Check the data changes to “01”.
1-7. 
PRECAUÇÃO SOBRE REPARO DA PLACA  VC-427
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right value.
Exif Model Data
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: A, address: B7 to BA, and set the Exif Model Data.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Page
A
A
A
A
Data
DCR-DVD405
34
30
35
00
DCR-DVD805
38
30
35
00
DCR-DVD404E
34
30
34
45
Address
B7
B8
B9
BA
DCR-DVD405E
34
30
35
45
DCR-DVD805E
38
30
35
45
1-5
DCR-DVD405_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1. SERVICE NOTE
1-2. イジェクトしない時のディスク取出し方法(強制イジェクト)
1
ねじ(M1.7)とフロントカバー(195)を外す。
2
穴に針金等を差し込み,イジェクトスライダを下げる。
1-3. 強制電源ONモードの設定
調整リモコン(RM-95またはNEW LANC JIG)を使用して,電源を入れることが出来ます。
カムコーダの操作は調整リモコンで行えます。
1-3-1. 強制Movie電源ONモードの設定
1) ページ:0,アドレス:01にデータ:01をセット。
2) ページ:A,アドレス:10にデータ:01をセットしPAUSE(Write)ボタンを押す。
1-3-2. 強制Play/Edit電源ONモードの設定
1) ページ:0,アドレス:01にデータ:01をセット。
2) ページ:A,アドレス:10にデータ:02をセットしPAUSE(Write)ボタンを押す。
1-3-3. 強制電源ONモードの解除
1) ページ:0,アドレス:01にデータ:01をセット。
2) ページ:A,アドレス:10にデータ:00をセットしPAUSE(Write)ボタンを押す。
3) ページ:0,アドレス:01にデータ:00をセット。
1-1. 修理時の電源供給について
本機では,安定化電源(8.4Vdc)からバッテリ端子に電源を供給した場合,約10秒後にシャットオフし,動作しなくなります。
これを避けるため,下記の方法を用いてください。
方法:
DC入力端子を使用する。(ACアダプタ(AC-L200など)を使用する。)
イジェクトスライダ
チャージレバー
フロントカバー(195)
ねじ(M1.7)
1-6
DCR-DVD405_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-5. 自己診断機能
1-5-1.自己診断機能について
本機の動作に不具合が生じたとき,自己診断機能が働き,
ビューファインダまたはL C D 画面に,どう処置したらよい
か判断できる表示を行います。「自己診断表示」と「サービス
モード表示」の2つの表示があります。自己診断機能につい
ては取扱説明書にも掲載されています。
1-4. 使用サービス治具
1.延長ケーブル(J-6082-572-A)をMD-128基板CN3907とDVDメカデッキの間に接続します。
2.延長ケーブル(J-6082-578-A)をMD-128基板CN3901とVC-427基板CN1009の間に接続します。
DVDメカデッキ 
MD-128基板 (A面側)
VC-427基板 (B面側)
フレキシブル基板 (10P)
延長ケーブル (10P) 
(J-6082-572-A)
延長ケーブル (100P) 
(J-6082-578-A)
CN3907 
CN3901 
CN1009 
1 1
3 1
C
対応者分類
「1-5-3. 自己診断コード表」
を参照
対応方法の違いにより分類
例 31・・・テープを入れ直す
32・・・電源を入れ直す
ブロック分類
詳細コード
3.2Hz点滅
C :お客さま自身で対応
H :販売店で対応
E :サービスエンジニア
で対応
ビューファインダまたはLCD画面
C : 3 1 : 1 1
1-5-2.自己診断表示
本機の動作に不具合が生じたとき,ビューファインダまたは
LCD画面のカウンタ表示部分がアルファベットと数字の4桁
表示になり,3.2Hzで点滅します。この5文字の表示によっ
て対応者分類および不具合の生じたブロックの分類,不具合
の詳細コードを示します。
Page of 91
Display

Click on the first or last page to see other DCR-DVD405 (serv.man2) service manuals if exist.