Sony DCR-DVD306E / DCR-DVD308 / DCR-DVD308E / DCR-DVD708 / DCR-DVD708E (serv.man4) Service Manual ▷ View online
6-22
DCR-DVD306E/DVD308/DVD308E/DVD708/DVD708E_ADJ
Ver. 1.5 2008.04
8.
CAMERA Adjustment 5
[Switch setting]
1. POWER switch ............................................................ Movie
2. NIGHTSHOT PLUS switch ........................................ OFF
3. WIDE SELECT button ................................................ 4:3
1. POWER switch ............................................................ Movie
2. NIGHTSHOT PLUS switch ........................................ OFF
3. WIDE SELECT button ................................................ 4:3
[Picture Frame Setting (Color reproduction adjustment
frame)]
1) Shoot the color bar chart.
frame)]
1) Shoot the color bar chart.
PTB-450: 1 m from the front of lens
PTB-1450: 40 cm from the front of lens
PTB-1450: 40 cm from the front of lens
2) Adjust the zoom and the camera direction, and set the speci-
fied position.
Check on the oscilloscope
1. Horizontal period
2. Vertical period
Check on the monitor TV (Underscanned mode)
Fig. 6-1-14
[Adjusting method]
1) Click the [Start] button in CAMERA Adjustment 5, and the
1) Click the [Start] button in CAMERA Adjustment 5, and the
following screen will appear.
2) Select the model (NTSC or PAL) with the Model Select radio
button.
Note:
NTSC model: DCR-DVD308/DVD708
PAL model: DCR-DVD306E/DVD308E/DVD708E
PAL model: DCR-DVD306E/DVD308E/DVD708E
3) Click the [Color Reproduction Adjustment] button.
4) The following message will be displayed, and then shoot the
color bar chart and set the picture frame, and then click the
[OK] button.
(Refer to “Picture Frame Setting”)
[OK] button.
(Refer to “Picture Frame Setting”)
A = B
C = D
A
B
C
D
H
E = F
V
E
F
Color bar chart picture frame
Monitor TV picture frame
6-23
DCR-DVD306E/DVD308/DVD308E/DVD708/DVD708E_ADJ
Ver. 1.5 2008.04
5) The data with the color bar chart are captured, and then the
following message will be displayed.
With the picture frame setting retained, replace the color bar
chart with the clear chart and press the [OK] button.
With the picture frame setting retained, replace the color bar
chart with the clear chart and press the [OK] button.
6) The data with the clear chart are captured, and then the fol-
lowing message will be displayed.
With the clear chart in shooting state, place the C14 filter on
the lens and click the [OK] button.
With the clear chart in shooting state, place the C14 filter on
the lens and click the [OK] button.
7) The data with the clear chart + C14 filter are captured, and
then the following message will be displayed.
Replace the clear chart with the color bar chart, and with the
C14 filter placed on the lens, click the [OK] button.
Replace the clear chart with the color bar chart, and with the
C14 filter placed on the lens, click the [OK] button.
8) The data with the color bar chart
+ C14 filter are captured, the
adjustment value is calculated, and it is written to the
camcorder.
Upon successful completion, the following message will be
displayed.
Click the [OK] button, and thus the adjustment is complete.
camcorder.
Upon successful completion, the following message will be
displayed.
Click the [OK] button, and thus the adjustment is complete.
[Checking method]
1) Click the [Start] button in CAMERA Adjustment 5, and the
1) Click the [Start] button in CAMERA Adjustment 5, and the
following screen will appear.
2) Select the model (NTSC or PAL) with the Model Select radio
button.
Note:
NTSC model: DCR-DVD308/DVD708
PAL model: DCR-DVD306E/DVD308E/DVD708E
PAL model: DCR-DVD306E/DVD308E/DVD708E
3) Click the [Color Reproduction Check] button.
4) The following message will be displayed, and then shoot the
color bar chart and set the picture frame, and then click the
[OK] button.
(Refer to “Picture Frame Setting”)
[OK] button.
(Refer to “Picture Frame Setting”)
6-24
DCR-DVD306E/DVD308/DVD308E/DVD708/DVD708E_ADJ
5) The color reproduction is checked, and if within the specifica-
tion, the following message will be displayed.
Click the [OK] button, and thus the color reproduction check
is complete.
Click the [OK] button, and thus the color reproduction check
is complete.
6) If the color reproduction check results in NG, the following
message will be displayed.
Note:
Before clicking the [OK] button, check the data dis-
played on the SeusEX screen. Error codes will be dis-
played.
If the [OK] button is clicked, the processing after ad-
justment is executed and the error codes cannot be
checked.
played on the SeusEX screen. Error codes will be dis-
played.
If the [OK] button is clicked, the processing after ad-
justment is executed and the error codes cannot be
checked.
[Error Code Table]
Of the error code data, check the bits of which bit value is “1”, so
that the contents of error can be confirmed.
(For how to read bit values, see “Bit Value Discrimination”)
Of the error code data, check the bits of which bit value is “1”, so
that the contents of error can be confirmed.
(For how to read bit values, see “Bit Value Discrimination”)
bit
Contents of Error
0
Blue NG
1
Red NG
2
Magenta NG
3
White NG
4
Green NG
5
Cyan NG
6
Yellow NG
7
Color bar Search NG
[Bit Value Discrimination]
The bit values must be discriminated from the data displayed on
the SeusEX. Whether bit values are “1” or “0” can be discrimi-
nated from the table shown below.
The bit values must be discriminated from the data displayed on
the SeusEX. Whether bit values are “1” or “0” can be discrimi-
nated from the table shown below.
Data displayed on SeusEX
0 0
bit3 to bit0 discriminated
bit7 to bit4 discriminated
Ver. 1.5 2008.04
Bit values
Display on the
bit3
bit2
bit1
bit0
SeusEX
or
or
or
or
bit7
bit6
bit5
bit4
0
0
0
0
0
1
0
0
0
1
2
0
0
1
0
3
0
0
1
1
4
0
1
0
0
5
0
1
0
1
6
0
1
1
0
7
0
1
1
1
8
1
0
0
0
9
1
0
0
1
A
1
0
1
0
B
1
0
1
1
C
1
1
0
0
D
1
1
0
1
E
1
1
1
0
F
1
1
1
1
B
A
Example: If the displayed data is “8E”, bit7 - bit4 values can be
discriminated from block (A), and also bit3 - bit0 val-
ues from block (B).
ues from block (B).
Example: If the displayed data is “01” (bit0 = 1), the Contents of
Error is “Blue NG”.
If the displayed data is “05” (bit0 = 1, bit2 = 1), the
Contents of Error is “Blue NG” and “Magenta NG”.
If the displayed data is “05” (bit0 = 1, bit2 = 1), the
Contents of Error is “Blue NG” and “Magenta NG”.
6-25
DCR-DVD306E/DVD308/DVD308E/DVD708/DVD708E_ADJ
9.
CAMERA Adjustment 6
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Picture Frame Setting (AWB Adjustment Frame)
3. AWB Standard Data Input
4. LV Standard Data Input
5. AWB Adj.
6. AWB Check
7. Release of Data Setting during Camera Adj.
sequence]
1. Data Setting during Camera Adj.
2. Picture Frame Setting (AWB Adjustment Frame)
3. AWB Standard Data Input
4. LV Standard Data Input
5. AWB Adj.
6. AWB Check
7. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Select the model (NTSC Model or PAL Model) with the Model
1) Select the model (NTSC Model or PAL Model) with the Model
Select radio button.
Note:
NTSC model: DCR-DVD308/DVD708
PAL model: DCR-DVD306E/DVD308E/DVD708E
PAL model: DCR-DVD306E/DVD308E/DVD708E
2) Click the [Start] button of the CAMERA Adjustment 6.
3) The Automatic Adjustment Program executes “1. Data Setting
3) The Automatic Adjustment Program executes “1. Data Setting
during Camera Adj.”.
4) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Then, set
the picture frame in accordance with the message.
the picture frame in accordance with the message.
5) If the [OK] button is clicked, “2. Picture Frame Setting (AWB
Adjustment Frame)” is executed. The following messages are
displayed in the order given below during the execution. Then,
change the chart in accordance with the messages.
displayed in the order given below during the execution. Then,
change the chart in accordance with the messages.
Ver. 1.5 2008.04
6) After the setting, if the [OK] button is clicked, the adjustment
items from “3. AWB Standard Data Input” to “6. AWB Check”
are executed. During the execution, the following messages
are displayed in the order given below. Place or remove the
filters on the lens in accordance with the messages.
are executed. During the execution, the following messages
are displayed in the order given below. Place or remove the
filters on the lens in accordance with the messages.
7) Upon completion of “6. AWB Check”, “7. Release of Data
Setting during Camera Adj.” is executed
8) Upon successful completion of all items of the CAMERA
Adjustment 6, the following message is displayed. Click the
[OK] button.
[OK] button.
Click on the first or last page to see other DCR-DVD306E / DCR-DVD308 / DCR-DVD308E / DCR-DVD708 / DCR-DVD708E (serv.man4) service manuals if exist.