Sony DCR-DVD201 / DCR-DVD201E (serv.man2) Service Manual ▷ View online
— 6 —
DCR-DVD201/DVD201E
TABLE OF CONTENTS
1.
SERVICE NOTE
1-1.
SERVICE NOTE ····························································· 1-1
1.
NOTE FOR REPAIR ······················································· 1-1
2.
POWER SUPPLY DURING REPAIRS ·························· 1-2
3.
TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ····························································· 1-2
(FORCE EJECT) ····························································· 1-2
4.
NOTES ON HANDLING THE OPTICAL PICK-UP ···· 1-2
5.
PRECAUTION FOR CHECKING EMISSION
OF LASER DIODE ························································· 1-2
OF LASER DIODE ························································· 1-2
1-2.
SELF-DIAGNOSIS FUNCTION ···································· 1-3
1.
SELF-DIAGNOSIS FUNCTION ···································· 1-3
2.
SELF-DIAGNOSIS DISPLAY ······································· 1-3
3.
SELF-DIAGNOSIS CODE TABLE ································ 1-3
2.
DISASSEMBLY
2-1.
DISASSEMBLY ······························································ 2-1
2-2.
SERVICE POSITION ····················································· 2-5
2-3.
CIRCUIT BOARDS LOCATION ··································· 2-8
2-4.
FLEXIBLE BOARDS LOCATION ································ 2-9
Disassembling procedure of MD block assembly is
not shown. Page 2-10 is not shown.
not shown. Page 2-10 is not shown.
HELP (List of caution points is shown here.)
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM (1/4) ··························· 3-1
3-2.
OVERALL BLOCK DIAGRAM (2/4) ··························· 3-3
3-3.
OVERALL BLOCK DIAGRAM (3/4) ··························· 3-5
3-4.
OVERALL BLOCK DIAGRAM (4/4) ··························· 3-7
3-5.
POWER BLOCK DIAGRAM (1/3) ································ 3-9
3-6.
POWER BLOCK DIAGRAM (2/3) ······························ 3-11
3-7.
POWER BLOCK DIAGRAM (3/3) ······························ 3-13
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM (1/3) ······················· 4-1
FRAME SCHEMATIC DIAGRAM (2/3) ······················· 4-3
FRAME SCHEMATIC DIAGRAM (3/3) ······················· 4-5
FRAME SCHEMATIC DIAGRAM (2/3) ······················· 4-3
FRAME SCHEMATIC DIAGRAM (3/3) ······················· 4-5
4-2.
SCHEMATIC DIAGRAMS
• CD-504 (CCD IMAGER)
SCHEMATIC DIAGRAM ···························· 4-11
• FP-884 (LITHIUM BATTERY, SW)
SCHEMATIC DIAGRAM ···························· 4-13
• FP-887 (USB JACK) FLEXIBLE
SCHEMATIC DIAGRAM ···························· 4-15
• FP-890 (PANEL REV SW) FLEXIBLE
SCHEMATIC DIAGRAM ···························· 4-15
• FP-891 (EJECT MOTOR, SW) FLEXIBLE
SCHEMATIC DIAGRAM ···························· 4-17
• LB-107 (EVF I/F, BACK LIGHT)
SCHEMATIC DIAGRAM ···························· 4-17
• JS-030 (KEY I/F)
SCHEMATIC DIAGRAM ···························· 4-19
• MA-429 (MIC, REMOTE SENSOR, MULTI AV JACK)
SCHEMATIC DIAGRAM ···························· 4-21
• SE-143 (PITCH/YAW SENSOR)
SCHEMATIC DIAGRAM ···························· 4-23
• PD-220 (LCD DRIVE)
SCHEMATIC DIAGRAM ···························· 4-25
• CONTROL SWITCH BLOCK (BL8700, PS8700)
SCHEMATIC DIAGRAM ···························· 4-27
• CONTROL SWITCH BLOCK (SH8700)
SCHEMATIC DIAGRAM ···························· 4-29
Shematic diagram of the MD-104 board and VC-354
are not shown.
Pages from 4-31 to 4-82 are not shown.
are not shown.
Pages from 4-31 to 4-82 are not shown.
4-3.
PRINTED WIRING BOARDS
• CD-504 (CCD IMAGER)
PRINTED WIRING BOARD ······················· 4-85
• FP-890 (PANEL REV SW)
PRINTED WIRING BOARD ······················· 4-87
• FP-884 (LITHIUM BATTERY, SW) FLEXIBLE
PRINTED WIRING BOARD ······················· 4-88
• JS-030 (KEY I/F)
PRINTED WIRING BOARD ······················· 4-89
• MA-429 (MIC, REMOTE SENSOR, MULTI AV JACK)
PRINTED WIRING BOARD ······················· 4-91
• PD-220 (LCD DRIVE)
PRINTED WIRING BOARD ······················· 4-93
• LB-107 (EVF I/F, BACK LIGHT)
PRINTED WIRING BOARD ······················· 4-95
• SE-143 (PITCH/YAW SENSOR)
PRINTED WIRING BOARD ······················· 4-95
Printed wiring board of the MD-104 board and VC-354
are not shown.
Pages from 4-97 to 4-104 are not shown.
are not shown.
Pages from 4-97 to 4-104 are not shown.
4-4.
MOUNTED PARTS LOCATION ······························· 4-105
Mounted parts location of the MD-104 board and
VC-354 are not shown.
Pages from 4-106 to 4-108 are not shown.
VC-354 are not shown.
Pages from 4-106 to 4-108 are not shown.
5.
REPAIR PARTS LIST
5-1.
EXPLODED VIEWS ······················································ 5-3
5-1-1. OVERALL SECTION ····················································· 5-3
5-1-2. CABINET (R) SECTION ··············································· 5-4
5-1-3. LCD SECTION ······························································· 5-5
5-1-4. EVF SECTION ································································ 5-6
5-1-5. LENS SECTION ····························································· 5-7
5-1-6. CABINET (L) SECTION ················································ 5-8
5-1-7. D LID SECTION ····························································· 5-9
5-1-2. CABINET (R) SECTION ··············································· 5-4
5-1-3. LCD SECTION ······························································· 5-5
5-1-4. EVF SECTION ································································ 5-6
5-1-5. LENS SECTION ····························································· 5-7
5-1-6. CABINET (L) SECTION ················································ 5-8
5-1-7. D LID SECTION ····························································· 5-9
Exploded view and parts list of MD BLOCK are not
shown. Pages 5-10 and 5-11 are not shown.
shown. Pages 5-10 and 5-11 are not shown.
Checking supplied accessories. ····································· 5-12
5-2.
ELECTRICAL PARTS LIST ········································ 5-14
Electrical parts list of the
MD-104 board and
VC-354 board are not shown.
Pages from 5-17 to 5-30 are not shown.
Pages from 5-17 to 5-30 are not shown.
1-1
SECTION 1
SERVICE NOTE
DCR-DVD201/DVD201E
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
1-1. SERVICE NOTE
1.
NOTE FOR REPAIR
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-2
DCR-DVD201/DVD201E
2.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor.
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
3.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Remove the front panel assembly.
2
Remove the cabinet (R) assembly.
3
Remove the lens block.
4
Remove the EVF block.
5
Remove the cabinet center (M) assembly.
6
Push the portion A in the direction of the arrow and open the disc cover.
ENGLISH
JAPANESE
ENGLISH
JAPANESE
A
4.
NOTES ON HANDLING THE OPTICAL PICK-UP
The laser diode may suffer electrostatic breakdown because of the
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
5.
PRECAUTION FOR CHECKING EMISSION OF
LASER DIODE
LASER DIODE
Laser light of the equipment is focused by the object lens in the
optical pick-up so that the light focuses on the reflection surface of
the disc. Therefore, be sure to keep your eyes more then 30 cm
apart from the object lens when you check the emission of laser
diode.
optical pick-up so that the light focuses on the reflection surface of
the disc. Therefore, be sure to keep your eyes more then 30 cm
apart from the object lens when you check the emission of laser
diode.
1-3
DCR-DVD201/DVD201E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-2. SELF-DIAGNOSIS FUNCTION
1.
SELF-DIAGNOSIS FUNCTION
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder, or LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder, or LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
2.
SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen consists of an alphabet and 4-digit number,
which blinks at 3.2Hz. This 5-character display indicates the
“repaired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
viewfinder or LCD screen consists of an alphabet and 4-digit number,
which blinks at 3.2Hz. This 5-character display indicates the
“repaired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
Note:
The “self-diagnosis display” data will be kept even if the lithium battery (FP-884 flexible board BT5201 of the cabinet (R) assembly) is removed.
0 0
1 3
C
Repaired by:
Self-diagnosis Code Table.
Indicates the appropriate
step to be taken.
E.g.
13....Faulty disc is used.
step to be taken.
E.g.
13....Faulty disc is used.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD screen
C : 1 3 : 0 0
3.
SELF-DIAGNOSIS CODE TABLE
C
C
C
E
E
E
E
E
E
Block
Function
0
4
1
3
2
1
2
0
6
1
6
1
6
2
9
3
9
4
Detailed
Code
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
Symptom/State
Non-standard battery is used.
Faulty disc is used.
Condensation.
EEPROM data are rewritten.
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Handshake correction function does not
work well. (With pitch angular velocity
sensor output stopped.)
work well. (With pitch angular velocity
sensor output stopped.)
USB bridge IC fault
Fault of writing to or erasing the flash
memory
memory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Make EEPROM data correct value. (Note)
Inspect the lens block focus MR sensor (Pin 1, 2 of CN1501 of
VC-354 board) when focusing is performed when the control button
is pressed in the focus manual mode and inspect the focus motor drive
circuit (IC1501 of VC-354 board) when the focusing is not performed.
VC-354 board) when focusing is performed when the control button
is pressed in the focus manual mode and inspect the focus motor drive
circuit (IC1501 of VC-354 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin wh of CN1501 of
VC-354 board) when zooming is performed when the zoom switch
is pressed and inspect the zoom motor drive circuit (IC1501 of
VC-354 board) when the zooming is not performed.
VC-354 board) when zooming is performed when the zoom switch
is pressed and inspect the zoom motor drive circuit (IC1501 of
VC-354 board) when the zooming is not performed.
Inspect angular velocity sensors (SE5501, 5502 of SE-143
board) peripheral circuits.
board) peripheral circuits.
Inspect the USB bridge IC (MD-104 board IC4201) and EEPROM
(MD-104 board IC4200)
(MD-104 board IC4200)
Inspect the flash memory (VC-354 board IC3401) (Note)
Note:
Refer to “9. Record of Self-diagnosis check” of “6-3. SERVICE
MODE”, ADJ (987671551.pdf).
Click on the first or last page to see other DCR-DVD201 / DCR-DVD201E (serv.man2) service manuals if exist.