DOWNLOAD Sony DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E Service Manual ↓ Size: 3.64 MB | Pages: 38 in PDF or view online for FREE

DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L3

2010C0800-1

  © 2010.03

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.

Les composants identifiés par une
marque  0  sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

Photo: DCR-DVD650

US Model

Canadian Model

AEP Model

UK Model

East European Model

North European Model

E Model

Australian Model

Argentine Model

Brazilian Model

— 2 —

DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L3

• Abbreviation

AR

: Argentine model

AUS : Australian model
BR

: Brazilian model

CND : Canadian model
EE

: East European model

NE

: North European model

Model

DCR-DVD150E

DCR-DVD450E

DCR-DVD650

DCR-DVD650E

DCR-DVD850

DCR-DVD850E

Destination

AEP, UK,

AEP, UK,

US, CND, E,

NE, E, AUS

US, CND, E,

NE, E

EE

EE

AR, BR

AR, BR

Color system

PAL

PAL

NTSC

PAL

NTSC

PAL

Recording sound format

2ch STEREO

5.1ch SURROUND

2ch STEREO

2ch STEREO

5.1ch SURROUND 5.1ch SURROUND

Data

CAM 

→ PC

a

a

a

a

a

a

copy

PC 

→ CAM

×

×

a

a

a

a

Internal flash memory

×

a

×

×

a

a

— 3 —

DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L3

0

0

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

0

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

CAUTION
Use of controls or adjustments or perfor mance
procedures other than those specified herein may
result in hazardous radiation exposure.

The use of optical instrument with this product will increase eye
hazard.

CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L3