Sony DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E (serv.man2) Service Manual ▷ View online
1-1
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200C/L200D).
1-2. TO TAKE OUT A DISC WHEN NOT EJECT (FORCE EJECT)
1
Open the jack cover and remove the remote control window.
2
Insert the wire etc. in the hole and down the eject slider by it.
1-3. PRECAUTION ON REPLACING THE VC-552 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• USB SERIAL No.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Hole
Remote Control Window
Jack Cover
Charge Lever
Eject Slider
1-2
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
1-4. USING SERVICE JIG
Connect the extension cable (J-6082-572-A) between the DVD mechanism deck and CN4401 on the VC-552 board.
DVD mechanism deck
VC-552 board (side A)
Flexible board (10P)
Extension cable (10P)
(J-6082-572-A)
CN4401
1 1
3 1
C
Repaired by:
Refer to “1-5-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD screen
C : 3 1 : 1 1
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder or LCD
screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
1-3E
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
1-5-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
1
2
0
3
1
6
1
6
1
6
1
9
4
9
4
Detailed
Code
0
0
0
1
0
2
0
0
0
0
0
0
0
0
1
0
1
1
0
0
0
1
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Disc access error
Condensaton.
Flash memory data are rewritten.
Drive fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Fault of writing to or erasing the flash
memory
memory
Internal flash memory fault
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Make flash memory data correct value. (Note 1)
Inspect or replacement of the mechanism deck, IC (IC4401 on
the VC-552 board) and drive block.
the VC-552 board) and drive block.
Inspect the lens block focus reset sensor (pin 8 of CN5401 on
the VC-552 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC5401 on the VC-552 board)
when the focusing is not performed.
the VC-552 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC5401 on the VC-552 board)
when the focusing is not performed.
Inspect the lens block zoom reset sensor (pin 0 of CN5401 on
the VC-552 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5401 on
the VC-552 board) when zooming is not performed.
the VC-552 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5401 on
the VC-552 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5401 on the VC-552 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5401 on the VC-552 board).
Inspect the flash memory (IC7801 on the VC-552 board). (Note 1)
Inspect the internal flash memory (IC8701 on the VC-552 board)
(DVD450E/DVD850/DVD850E only)
(DVD450E/DVD850/DVD850E only)
Note 1:
Start the Adjust manual in the Adjust station and refer to the “DESTINATION DATA WRITE”.
2-1
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Click on the first or last page to see other DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E (serv.man2) service manuals if exist.