DOWNLOAD Sony DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E (serv.man2) Service Manual ↓ Size: 4.52 MB | Pages: 69 in PDF or view online for FREE

Model
DCR-DVD150E DCR-DVD450E DCR-DVD650 DCR-DVD650E DCR-DVD850 DCR-DVD850E (serv.man2)
Pages
69
Size
4.52 MB
Type
PDF
Document
Service Manual
Brand
Device
Movie
File
dcr-dvd150e-dcr-dvd450e-dcr-dvd650-dcr-dvd650e-dcr.pdf
Date

Sony DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E (serv.man2) Service Manual ▷ View online

— 5 —
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
WARNING!!
WHEN  SERVICING,  DO  NOT  APPROACH  THE  LASER
EXIT  WITH  THE  EYE  TOO  CLOSELY.  IN  CASE  IT  IS
NECESSARY  TO  CONFIRM  LASER  BEAM  EMISSION,
BE  SURE  TO  OBSERVE  FROM  A  DISTANCE  OF MORE
THAN   30  cm  FROM  THE  SURFACE  OF  THE
OBJECTIVE  LENS  ON  THE  OPTICAL  PICK-UP  BLOCK.
CAUTION
Use of controls or adjustments or perfor mance
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
1-1
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
1. SERVICE  NOTE
1-1. POWER  SUPPLY  DURING  REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200C/L200D).
1-2. TO  TAKE  OUT  A  DISC  WHEN  NOT  EJECT (FORCE  EJECT)
1
Open the jack cover and remove the remote control window.
2
Insert the wire etc. in the hole and down the eject slider by it.
1-3. PRECAUTION  ON  REPLACING  THE  VC-552  BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• USB SERIAL No.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Hole
Remote Control Window
Jack Cover
Charge Lever
Eject Slider
1-2
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
1-4. USING  SERVICE  JIG
Connect the extension cable (J-6082-572-A) between the DVD mechanism deck and CN4401 on the VC-552 board.
DVD mechanism deck
VC-552 board (side A)
Flexible board (10P)
Extension cable (10P)
(J-6082-572-A)
CN4401
1 1
3 1
C
Repaired by:
Refer to “1-5-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD screen
C : 3 1 : 1 1
1-5. SELF-DIAGNOSIS  FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
1-3E
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
1-5-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
1
2
0
3
1
6
1
6
1
6
1
9
4
9
4
Detailed
Code
0
0
0
1
0
2
0
0
0
0
0
0
0
0
1
0
1
1
0
0
0
1
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
Disc access error
Condensaton.
Flash memory data are rewritten.
Drive fault
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Fault of writing to or erasing the flash
memory
Internal flash memory fault
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Clean the disc with the supplied cleaning cloth.
Use a compatible disc with the camcorder.
Remove the disc, and insert it again after one hour.
Make flash memory data correct value. (Note 1)
Inspect or replacement of the mechanism deck, IC (IC4401 on
the VC-552 board) and drive block.
Inspect the lens block focus reset sensor (pin 8 of CN5401 on
the VC-552 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor drive circuit (IC5401 on the VC-552 board)
when the focusing is not performed.
Inspect the lens block zoom reset sensor (pin 0 of CN5401 on
the VC-552 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5401 on
the VC-552 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5401 on the VC-552 board).
Inspect the flash memory (IC7801 on the VC-552 board). (Note 1)
Inspect the internal flash memory (IC8701 on the VC-552 board)
(DVD450E/DVD850/DVD850E only)
Note 1:
Start the Adjust manual in the Adjust station and refer to the “DESTINATION DATA WRITE”.
Page of 69
Display

Click on the first or last page to see other DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E (serv.man2) service manuals if exist.