Sony DCR-DVD150E / DCR-DVD450E / DCR-DVD650 / DCR-DVD650E / DCR-DVD850 / DCR-DVD850E (serv.man2) Service Manual ▷ View online
— 3 —
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
SPECIFICATIONS
These specifications are extracted from instruction
manual of DCR-DVD650/DVD850.
manual of DCR-DVD650/DVD850.
System
Video compression format
MPEG2/JPEG (Still images)
Audio compression format
DCR-DVD650
Dolby Digital 2ch
Dolby Digital Stereo Creator
Dolby Digital Stereo Creator
DCR-DVD850
Dolby Digital 2ch/5.1ch
Dolby Digital 5.1 Creator
Dolby Digital 5.1 Creator
Video signal
NTSC color, EIA standards
Internal memory (DCR-DVD850)
16GB
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
data management.
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
data management.
Usable discs
8 cm DVD-RW/DVD+RW/DVD-R/
DVD+R DL
DVD+R DL
Movie recording format
Internal memory (DCR-DVD850)
MPEG2-PS
Disc
DVD-RW: DVD-VIDEO (VIDEO mode),
DVD-Video Recording (VR mode)
DVD+RW: DVD+RW Video
DVD-R/DVD+R DL: DVD-VIDEO
DVD-Video Recording (VR mode)
DVD+RW: DVD+RW Video
DVD-R/DVD+R DL: DVD-VIDEO
“
Memory Stick PRO Duo
”
media
MPEG2-PS
Still image recording format
DCF Ver.2.0 Compatible
Exif Ver.2.21 Compatible
MPF Baseline Compatible
Exif Ver.2.21 Compatible
MPF Baseline Compatible
Viewfinder
Electric viewfinder (color)
Image device
2.25 mm (1/8 type) CCD (Charge Coupled
Device)
Gross:
Approx. 680 000 pixels
Effective (Movie, 16:9)
Approx. 410 000 pixels
Effective (Still, 16:9)
Approx. 250 000 pixels
Effective (Still, 4:3)
Approx. 340 000 pixels
Device)
Gross:
Approx. 680 000 pixels
Effective (Movie, 16:9)
Approx. 410 000 pixels
Effective (Still, 16:9)
Approx. 250 000 pixels
Effective (Still, 4:3)
Approx. 340 000 pixels
Lens
Carl Zeiss Vario-Tessar
Optical: 60
Optical: 60
×, Digital: 120×, 2 000×
Filter diameter: 30 mm (1 3/16 in.)
Focal length
F 1.8 - 6.0
f = 1.8 - 108 mm (3/32 - 4 3/8 in.)
When converted to a 35 mm still camera
For movies:
39 - 2 340 mm (1 9/16 - 92 1/4 in.) (16:9)
For still images:
44 - 2 640 mm (1 3/4 - 104 in.) (4:3)
f = 1.8 - 108 mm (3/32 - 4 3/8 in.)
When converted to a 35 mm still camera
For movies:
39 - 2 340 mm (1 9/16 - 92 1/4 in.) (16:9)
For still images:
44 - 2 640 mm (1 3/4 - 104 in.) (4:3)
Color temperature
[AUTO], [ONE PUSH], [INDOOR]
(3 200 K), [OUTDOOR] (5 800 K)
(3 200 K), [OUTDOOR] (5 800 K)
Minimum illumination
6 l
× (lux) ([AUTO SLW SHUTTR] [ON],
Shutter speed 1/30 second)
Input/Output connectors
A/V Remote Connector
Video/audio output jack
USB jack
mini-B
LCD screen
Picture
6.7 cm (2.7 type, aspect ratio 16:9)
Total number of pixels
123 200 (560
× 220)
General
Power requirements
DC 6.8 V/7.2 V (battery pack)
DC 8.4 V (AC Adaptor)
DC 8.4 V (AC Adaptor)
Average power consumption
DCR-DVD650
Using the LCD screen (normal brightness):
2.4 W
Using the Viewfinder: 2.2 W
2.4 W
Using the Viewfinder: 2.2 W
DCR-DVD850
Using the LCD screen (normal brightness):
2.1 W
Using the Viewfinder: 1.9 W
2.1 W
Using the Viewfinder: 1.9 W
Operating temperature
0 ºC to 40 ºC (32 ºF to 104 ºF)
Storage temperature
-20 ºC to +60 ºC (-4 ºF to +140 ºF)
Dimensions (Approx.)
55
× 89 × 130 mm (2 1/4 × 3 5/8 × 5 1/8 in.)
(w
×h×d) including the projecting parts
55
× 89 × 130 mm (2 1/4 × 3 5/8 × 5 1/8 in.)
(w
×h×d) including the projecting parts with
the rechargeable battery pack NP-FH30
attached
attached
Mass (Approx.)
DCR-DVD650
390 g (13 oz) main unit only
440 g (15 oz) including the rechargeable
battery pack NP-FH30 and a disc
440 g (15 oz) including the rechargeable
battery pack NP-FH30 and a disc
DCR-DVD850
390 g (13 oz) main unit only
430 g (15 oz) including the rechargeable
battery pack NP-FH30
430 g (15 oz) including the rechargeable
battery pack NP-FH30
Supplied accessories
AC Adaptor (1)
Power cord (mains lead) (1)
A/V connecting cable (1)
USB cable (1)
Rechargeable battery pack NP-FH30 (1)
CD-ROM “Handycam Application Software”
(1)
Operating Guide (1)
Power cord (mains lead) (1)
A/V connecting cable (1)
USB cable (1)
Rechargeable battery pack NP-FH30 (1)
CD-ROM “Handycam Application Software”
(1)
Operating Guide (1)
AC Adaptor AC-L200C/AC-L200D
Power requirements
AC 100 V - 240 V, 50 Hz/60 Hz
Current consumption
0.35 A - 0.18 A
Power consumption
18 W
Output voltage
DC 8.4 V*
Operating temperature
0 ºC to 40 ºC (32 ºF to 104 ºF)
Storage temperature
-20 ºC to +60 ºC (-4 ºF to +140 ºF)
Dimensions (Approx.)
48
× 29 × 81 mm (1 15/16 × 1 3/16 × 3 1/4 in.)
(w
×h×d) excluding the projecting parts
Mass (Approx.)
170 g (6.0 oz) excluding the power cord
(mains lead)
(mains lead)
* See at the label of the AC Adaptor for other
specifications.
specifications.
Rechargeable battery pack NP-FH30
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Maximum charge voltage
DC 8.4 V
Maximum charge current
2.12 A
Capacity
3.6 Wh (500 mAh)
Type
Li-ion
Design and specifications are subject to change
without notice.
without notice.
— 4 —
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
Model information table
• Abbreviation
AR
: Argentine model
AUS : Australian model
BR
BR
: Brazilian model
CND : Canadian model
EE
EE
: East European model
NE
: North European model
Model
DCR-DVD150E
DCR-DVD450E
DCR-DVD650
DCR-DVD650E
DCR-DVD850
DCR-DVD850E
Destination
AEP, UK,
AEP, UK,
US, CND, E,
NE, E, AUS
US, CND, E,
NE, E
EE
EE
AR, BR
AR, BR
Color system
PAL
PAL
NTSC
PAL
NTSC
PAL
Recording sound format
2ch STEREO
5.1ch SURROUND
2ch STEREO
2ch STEREO
5.1ch SURROUND 5.1ch SURROUND
Data
CAM
→ PC
a
a
a
a
a
a
copy
PC
→ CAM
×
×
a
a
a
a
Internal flash memory
×
a
×
×
a
a
— 5 —
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION
Use of controls or adjustments or perfor mance
procedures other than those specified herein may
result in hazardous radiation exposure.
Use of controls or adjustments or perfor mance
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
hazard.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
1-1
DCR-DVD150E/DVD450E/DVD650/
DVD650E/DVD850/DVD850E_L2
DVD650E/DVD850/DVD850E_L2
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200C/L200D).
1-2. TO TAKE OUT A DISC WHEN NOT EJECT (FORCE EJECT)
1
Open the jack cover and remove the remote control window.
2
Insert the wire etc. in the hole and down the eject slider by it.
1-3. PRECAUTION ON REPLACING THE VC-552 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• USB SERIAL No.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Hole
Remote Control Window
Jack Cover
Charge Lever
Eject Slider