Sony DCR-DVD101 / DCR-DVD101E / DCR-DVD91E (serv.man2) Service Manual ▷ View online
DCR-DVD91E/DVD101/DVD101E
2-1
2-2
2-1. DISASSEMBLY
The following flow chart shows the disassembly procedure.
VC-353
1
2
4
3
2
1
3
5
6
1
5
4
2
3
6
5
1
Two grip screws (M1.7x3) black
2
Two grip screws (M1.7x3) black
3
Six claws
4
P cabinet (C) assembly
5
Sheet (MY)
1
Open the jack cover
2
EG grip Screw (M1.7x4) black
3
EG grip Screw (M1.7x4) black
4
Turn over the EVF section in the
direction of the arrow.
5
EG grip Screw (M1.7x4) black
6
Two EG grip Screws (M1.7x4) black
7
Three EG grip Screws (M1.7x4) black
8
Two EG grip Screws (M1.7x4) black
9
Five claws
0
Remove the cabinet (R) section
in the direction of the arrow.
qa
MA-429 board (27P)
qs
F panel section
qd
FP-884 flexible board (33P)
qf
Cabinet (R) section
1
Two tapping screws (M1.7x3.5) silver
2
Speaker retainer plate assembly
3
Three tapping screws (M1.7x3.5) silver
4
FP-890 board (20P)
5
FP-884 flexible board (8P)
6
Three EG grip screws (M1.7x4) black
7
LCD section
1
Tape (0915)
2
Three screws (M1.7x2.5) silver
3
FP-892 flexible board (39P)
4
From lens flexible board (23P)
5
Lens section
1
Screw (M1.7x2.5) silver
2
VC heat sink, VC radiation sheet,
VC insulating sheet
3
Three screws (M1.7x2.5) silver
4
Control switch block (PS8700) (20P)
5
Board to board (CN1007, CN4901) (100P)
6
Radiation sheet (135)
7
VC-353 board
1
Screw (M1.7x2.5) silver
2
EG grip screw (M1.7x4) black
3
FP-883 flexible board (10P)
4
FP-889 flexible board (20P)
5
EVF section
1
Grip screw (M1.7x3) black
2
Four claws
3
Hinge cover (O)
4
Hinge cover (U)
5
Hinge (87) assembly, FP-890 board
4
A
A
B
B
B
B
C
C
B
B
B
2
1
D
3
7
D
1
4
5
2
5
7
HELP 02
HELP 01
2
3
1
A
4
5
D
3
4
4
3
1
2
5
D
6
Screw
M1.7x3
3-084-817-21
Screw
M1.7x2.5
3-078-889-11
Silver
Black
Screw
M1.7x4
3-087-376-01
Tapping screw
M1.7x3.5
3-078-890-01
Tapping screw
M1.7x5
3-081-204-21
A
C
B
D
E
1
Screw (M1.7x2.5) silver
2
Front fixed plate
3
EG grip screw (M1.7x4) black
4
Screw (M1.7x2.5) silver
5
Two tapping screws (M1.7x5) black
6
Claw
7
Remove the cabinet center (M) assembly
in the direction of the arrow.
3
4
5
2
6
B
1
7
D
E
D
See page
2-3.
1
Two grip screws (M1.7x3) black
2
Two grip screws (M1.7x3) black
3
Six claws
4
P cabinet (C) assembly
5
FP-890 board (22P)
6
Hinge (87) assembly, Hinge cover (O),
Hinge cover (U), FP-890 board
7
Sheet (MY)
8
Screw (M1.7x5) black
9
Control switch block (BL8700) (6P)
0
Two claws
qa
P cabinet (M) assembly
qs
PD-220 board, Insulating sheet,
Light guide plate block
8
5
4
3
1
7
9
qa
2
0
6
qs
A
A
E
7
9
qa
qf
qd
0
qs
B
B
B
8
1
2
1
Push this portion with a finger
in the direction of the arrow a.
2
Open the D lid assembly
in the direction of the arrow b.
a
b
SECTION 2
DISASSEMBLY
2. DISASSEMBLY
2. DISASSEMBLY
DCR-DVD91E/DVD101/DVD101E
2-3
2-4
VC-353
VC-353
MD-104
MD-104
1
Screw (M1.7x2.5) silver
2
VC heat sink, VC radiation sheet,
VC insulating sheet
3
Screw (M1.7x2.5) silver
4
Claw
5
Screw (M1.7x2.5) silver
E
E
D
D
C
7
2
5
6
3
1
1
E
1
2
2
4
1
Three screws (M1.7x2.5) silver
2
Board to board (CN1007, CN4901) (100P)
3
Radiation sheet (135)
4
VC-353 board
1
Screw (M1.7x2.5) silver
2
VM heat sink, VM radiation sheet, VM insulating sheet
3
Tripod large
4
Sheet radiation (2345)
1
Two screws (M1.7x2.5) silver
2
Screw (M1.7x2.5) silver
3
Three tapping screws (M1.7x5) black
4
Tapping screw (M1.7x3.5) silver
1
Two tapping screws (M1.7x5) black
2
D blind plate assembly
1
Two tapping screws (M1.7x5) black
2
Remove the D lid assembly
in the direction of the arrow.
D
1
D
1
3
4
4
3
2
5
DC-IN connector inlet (3P)
6
Harness (DM-144) (2P) (Dew sensor)
7
FP-891 flexible board (10P)
8
Remove the MD section in the
direction of the arrow.
6
Two EG grip screws (M1.7x4) black
7
Control switch block (PS8700) (20P)
8
Battery terminal board (3P)
9
Battery terminal board
0
FP-887 flexible board (8P)
qa
Square type connector (USB 5P),
FP-887 flexible board
(DVD101/DVD101E model)
(DVD101/DVD101E
model)
2
Screw
M1.7x3
3-084-817-21
Screw
M1.7x2.5
3-078-889-11
Silver
Black
Screw
M1.7x4
3-087-376-01
Tapping screw
M1.7x3.5
3-078-890-01
Tapping screw
M1.7x5
3-081-204-21
A
C
B
D
E
8
Refer to level 3
Disassembling procedure of
MD block assembly.
MD block assembly.
C
2
1
3
4
1
Remove the grip belt
in the direction of the arrow.
2
Two tapping screw (M1.7x3.5) silver
3
Grip belt sheet metal (Rear)
4
Grip belt
E
1
2
C
3
HELP 03
1
Two tapping screws (M1.7x5) black
2
Tapping screw (M1.7x3.5) silver
3
Control switch block (PS8700)
B
B
8
6
qa
5
3
0
4
D
D
D
1
7
9
2
3
1
Remove the grip belt
in the direction of the arrow a.
2
Push this portion with a finger
in the direction of the arrow b.
3
Open the D lid assembly
in the direction of the arrow c.
2
a
c
b
1
Optical pickup
Caution
Precautions during handling
Be sure to place the DVD drive with its
optical pickup facing upward.
Do not touch the optical pickup surface.
optical pickup facing upward.
Do not touch the optical pickup surface.
(J-2501-162-A)
Use the adjustable wrist strap (J-2501-162-A) as the
preventive measure for static electricity when the
removing and installing the MD black assembly because
the MD black assembly of this mechanism beck is easily
affected by the static electricity.
2
3
1
4
1
Open the jack cover (DC) in the directions of the arrows a and b.
2
DC-IN connector inlet
3
Harness (DM-144), FP-228 flexible board (Dew senser)
4
Control switch block (PS8700)
a
b
DCR-DVD91E/DVD101/DVD101E
2. DISASSEMBLY
2. DISASSEMBLY
2-5
2-6
2-2. SERVICE POSITION
VC-353
VC-353
2
1
3
B
B
5
6
4
B
B
3
4
5
2
6
B
1
7
D
E
D
D
1
4
3
2
2
3
Control switch block
(PS8700) (20P)
(PS8700) (20P)
Extension cable (100P)
(J-6082-352-A)
(J-6082-352-A)
AC power
adaptor
adaptor
AC IN
DC-IN
CN1006
CN1007
CN1001
CN4901
VC-353 board
MD-104 board
MD-104
VC-353
CN4902
4
3
1
2
5
D
Adjustment remote
commander (RM-95)
commander (RM-95)
LANC
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
[SERVICE POSITION TO CHECK THE DVD DRIVE SECTION]
Connection to Check the DVD drive section
Connection to Check the DVD drive section
To check the DVD drive section, set the DVD drive to PLAY mode. (Set the mode dial to PLAY position,
or set forced PLAY mode by using the adjustment remote commander.)
Operate the DVD drive using the adjustment remote commander (with the HOLD switch set in the OFF position).
Note: Removing the control switch block (PS8700) means removing the LID OPEN switch. Therefore the DVD
drive section will not move even if the forced PLAY mode is set up.
or set forced PLAY mode by using the adjustment remote commander.)
Operate the DVD drive using the adjustment remote commander (with the HOLD switch set in the OFF position).
Note: Removing the control switch block (PS8700) means removing the LID OPEN switch. Therefore the DVD
drive section will not move even if the forced PLAY mode is set up.
Setting the forced PLAY mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
Exiting the forced PLAY mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
Monitor TV
MA-429 board
AUDIO/
VIDEO jack
VIDEO jack
7
9
qa
qf
qd
0
qs
B
B
B
8
B
2
1
5
D
3
4
B
B
8
6
qa
5
3
0
4
D
D
D
1
7
9
2
2. DISASSEMBLY
2. DISASSEMBLY
DCR-DVD91E/DVD101/DVD101E
2-7
2-8
PD
-22
0
PD-220 board
AC power
adaptor
adaptor
AC IN
Adjustment remote
commander (RM-95)
commander (RM-95)
[PD-220 BOARD SERVICE POSITION]
LANC
1
2
4
3
5
A
A
2-3. CIRCUIT BOARDS LOCATION
VC-353
JS-030
MD-104
SE-143
CD-503
MA-429
PD-220
LB-101
CD-503
JS-030
PD-220
LB-101
MA-429
SE-143
JS-030
PD-220
LB-101
MA-429
SE-143
MD-104
NAME
FUNCTION
VC-353
CCD IMAGER
KEY I/F
LCD DRIVE
EVF I/F, BACKLIGHT
MIC, REMOTE SENSOR, MULTI AV JACK
PITCH/YAW SENSOR
RF PROCESS, DVD DSP, MECHA DRIVE, MICRO COMPUTER, FLASH, LATCH, USB I/F,
SHOCK SENSOR, CONNECTOR, DC/DC CONVERTER
A/D CONV., TIMING GENERATOR, CAMERA PROCESS, LENS CONTROL, LENS DRIVE,
DVD SYSTEM CONTROL, 128M SDRAM, 16M FCRAM, DVD CODEC,64M SDRAM,
VIDEO IN/OUT, VIDEO A/D CONVERTER, EVF DRIVE, CAMERA CONTROL, HI CONTROL,
HI/ DIGITAL STILL CONTROL, 32M FLASH MEMORY, AUDIO I/O, MIC AMP,
PITCH/YAW SENSOR AMP, CONNECTOR, DD CONNECTOR
KEY I/F
LCD DRIVE
EVF I/F, BACKLIGHT
MIC, REMOTE SENSOR, MULTI AV JACK
PITCH/YAW SENSOR
RF PROCESS, DVD DSP, MECHA DRIVE, MICRO COMPUTER, FLASH, LATCH, USB I/F,
SHOCK SENSOR, CONNECTOR, DC/DC CONVERTER
A/D CONV., TIMING GENERATOR, CAMERA PROCESS, LENS CONTROL, LENS DRIVE,
DVD SYSTEM CONTROL, 128M SDRAM, 16M FCRAM, DVD CODEC,64M SDRAM,
VIDEO IN/OUT, VIDEO A/D CONVERTER, EVF DRIVE, CAMERA CONTROL, HI CONTROL,
HI/ DIGITAL STILL CONTROL, 32M FLASH MEMORY, AUDIO I/O, MIC AMP,
PITCH/YAW SENSOR AMP, CONNECTOR, DD CONNECTOR
Click on the first or last page to see other DCR-DVD101 / DCR-DVD101E / DCR-DVD91E (serv.man2) service manuals if exist.