Sony DCR-DVD100 / DCR-DVD100E (serv.man4) Service Manual ▷ View online
6-5
DCR-DVD100/DVD100E
1-1-2.
Preparations
Note1:
For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
DISASSEMBLY”.
Note2:
When performing only the adjustments, the lens block and boards
need not be disassembled.
need not be disassembled.
Note3:
Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
address: 10 is “00”. If not, set data: 00 to this address.
1)
Connect the equipment for adjustments according to Fig. 6-1-3.
Note4:
As removing the cabinet (R) assembly (removing CN1007 of the
VC-307 board) means removing the lithium 3V power supply
(BT5201 on the CK-127 board), data such as date, time, user-set
menus will be lost. After completing adjustments, reset these data.
But the self-diagnosis data and the data on history of use (user
initial power on date, final condensation occurrence data) will be
kept even if the lithium 3V power supply is removed. (Refer to
“6-3. Service Mode” for the self-diagnosis data and the data on
history of use.)
VC-307 board) means removing the lithium 3V power supply
(BT5201 on the CK-127 board), data such as date, time, user-set
menus will be lost. After completing adjustments, reset these data.
But the self-diagnosis data and the data on history of use (user
initial power on date, final condensation occurrence data) will be
kept even if the lithium 3V power supply is removed. (Refer to
“6-3. Service Mode” for the self-diagnosis data and the data on
history of use.)
Note5:
Setting the “Forced MOVIE mode”.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button.
The above procedure will enable the camera power to be turned
on with the control switch block (PS-CX5500) removed. After
completing adjustments, be sure to exit the “Forced MOVIE mode”.
on with the control switch block (PS-CX5500) removed. After
completing adjustments, be sure to exit the “Forced MOVIE mode”.
Note6:
Exiting the “Forced MOVIE mode”.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button.
3) Select page: 0, address: 01, and set data: 00.
Fig. 6-1-2.
1.5 m
Front of the lens
Pattern box
6-6
DCR-DVD100/DVD100E
Fig. 6-1-3.
CPC lid
(bottom)
(bottom)
[CONNECTION OF EQUIPMENT]
Adjustment remote
commander (RM-95)
commander (RM-95)
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
Screw
(M1.7
(M1.7
×
4),
lock ace, p2
LANC jack
AC power
adaptor
adaptor
AC IN
DC-IN connector
6-7
DCR-DVD100/DVD100E
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
adjustments without loading cassette.
1.
MODE dial (PS-CX5500 block) ..................... MOVIE (
)
2.
NIGHT SHOT (Lens block) ............................................ OFF
3.
COLOR SLOW S/ SUPER NS ........................................ OFF
4.
FOCUS (KP-CX5500 block) ................................ MANUAL
5.
BACK LIGHT (FB-220 board) ........................................ OFF
6.
STEADY SHOT (Menu setting) ...................................... OFF
7.
DIGITAL ZOOM (Menu setting) .................................... OFF
8.
DEMO MODE (Menu setting) ........................................ OFF
9.
PROGRAM AE (Menu setting) ................................... AUTO
10. PICTURE EFECT (Menu setting) ................................... OFF
11. DIGITAL EFECT (Menu setting) .................................... OFF
12. WHITE BALANCE (Menu setting) ............................ AUTO
13. 16:9 WIDE (Menu setting) .............................................. OFF
11. DIGITAL EFECT (Menu setting) .................................... OFF
12. WHITE BALANCE (Menu setting) ............................ AUTO
13. 16:9 WIDE (Menu setting) .............................................. OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig. 6-1-4.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
Fig. 6-1-5.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
6-8
DCR-DVD100/DVD100E
COVER
COVER
1-2.
INITIALIZATION OF A, B, C, D, E, F, 1F
PAGE DATA
PAGE DATA
Note:
When reading or writing the 1F page data, select page: 0, address:
10, and set data: 01, then select F page. The 1F page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
10, and set data: 01, then select F page. The 1F page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1-2-1.
INITIALIZATION OF A, B, C, D PAGE DATA
Note:
The data of page: 0, address: 10 must be “00”.
1. Initializing the A, B, C, D Page Data
Note1:
Reading/writing the C page data by using the
is
impossible.
Note2:
If the B page data has been initialized, the following adjustments
need to be performed again.
1) Viewfinder system adjustments
2) LCD system adjustments
3) Video system adjustments
need to be performed again.
1) Viewfinder system adjustments
2) LCD system adjustments
3) Video system adjustments
Note3:
NTSC model: DCR-DVD100
PAL model: DCR-DVD100E
PAL model: DCR-DVD100E
Adjusting page
A
Adjusting Address
10 to FF
Adjusting page
B
Adjusting Address
30 to FF
Adjusting page
C
Adjusting Address
10 to FF
Adjusting page
D
Adjusting Address
10 to 75
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
7
03
Set the following data.
00(NTSC), 80(PAL)
00(NTSC), 80(PAL)
4
7
00
XX
Set the data. (Note4)
5
7
01
XX
Set the data, and press PAUSE
button. (Note4)
button. (Note4)
6
7
02
Check that the data changes to
“01”
“01”
7
Perform “Modification of A, B,
C, D Page Data”.
C, D Page Data”.
Note4:
XX=20 : Initializing A page
XX=21 : Initializing B page
XX=23 : Initializing D page
XX=24 : Initializing C page
XX=28 : Initializing A, B, C and D page
XX=21 : Initializing B page
XX=23 : Initializing D page
XX=24 : Initializing C page
XX=28 : Initializing A, B, C and D page
2. Modification of A, B, C, D Page Data
If the A, B, C or D page data has been initialized, change the data of
the “Fixed data-2” address of the initialized page shown in the
following tables by manual input.
the “Fixed data-2” address of the initialized page shown in the
following tables by manual input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Processing after Completing Modification of A, B, C, D Page data
Order Page Address Data
Procedure
1
0
01
00
Set the data.
2
Turn off the power and turn on
again
again
Note:
If the following symptoms occur after completing of the
“Modification of A, B, C, D page data”, check that the data of the
“Fixed data-2” addresses of A and D page are same as those of the
same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
“Modification of A, B, C, D page data”, check that the data of the
“Fixed data-2” addresses of A and D page are same as those of the
same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
Click on the first or last page to see other DCR-DVD100 / DCR-DVD100E (serv.man4) service manuals if exist.