Sony CCD-TRV128 / CCD-TRV228 / CCD-TRV228E / CCD-TRV328 / CCD-TRV428 / CCD-TRV428E (serv.man2) Service Manual ▷ View online
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
6-27
CN007
A/V OUT jack
16
1
Audio (black)
Video (yellow)
TV monitor
AC adaptor
AC IN
AC adaptor
CPC lid
Screw (M2)
I/F unit for LANC control
(J-6082-521-A)
(J-6082-521-A)
CPC jig connector
(J-6082-539-A)
(J-6082-539-A)
L serices Info
LITHIUM battery (7.2Vdc)
LITHIUM battery (7.2Vdc)
Adjustment
remote commander (RM-95)
remote commander (RM-95)
Conductor side
LANC jack
AC IN
3-1-2.
Precautions on Adjusting
This set is adjusted in two modes, VTR mode and CAMERA mode.
3-1-3. Adjusting Connectors
Some of the adjusting points of the video section are concentrated
at VC-341 board CN007. Connect the measuring instruments via
I/F unit for LANC control (J-6082-521-A) and CPC jig connector
(J-6082-539-A).
The following table shows the pin No. and signal name of CN007.
at VC-341 board CN007. Connect the measuring instruments via
I/F unit for LANC control (J-6082-521-A) and CPC jig connector
(J-6082-539-A).
The following table shows the pin No. and signal name of CN007.
Pin No.
Signal Name
Pin No.
Signal Name
1
EEP SCK
9
PB RF
2
PB RF
10
REG GND
3
BPF MONI
11
LANC OUT
4
CAP FG
12
LANC IN
5
SWP DIR
13
XLANC PWR ON
6
REG GND
14
EEP SO
7
REC RF
15
EEP SI
8
REG GND
16
XCS EEP
Table 6-3-1
Connecting the TV Monitor and Adjustment Remote Commander
Fig. 6-3-1
Note:
Use either the AC power adaptor or the InfoLITHIUM battery as the power supply of I/F unit for LANC control.
The following table lists the test point of I/F unit of for LANC
control.
control.
Pin No.
Signal Name
Pin No.
Signal Name
BL
15
EVF VCO
14
EVF VG
BL 4.75
9
PB RF (MON)
3
BPF MONI
6, 8, 10
GND
TMS
7
REC RF (RF IN)
TDI
TDO
5
SWP
TCK
4
CAP FG
2
IR VIDEO
Note:
Pin No. are those of CN007.
Table 6-3-2
3-1-4. Connecting the Equipment
Connect the measuring instruments as shown in Fig. 6-3-1 and
perform the adjustments.
perform the adjustments.
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
6-28
3-1-5.
Alignment Tapes
The following table lists alignment tapes which are available.
Use the tape specified in the signal column for each adjustment. If the type of tape to be used for checking operations is not specified, use
whichever type.
Use the tape specified in the signal column for each adjustment. If the type of tape to be used for checking operations is not specified, use
whichever type.
Alignment tape
Tape type:
ME .................................. Particle type metal tape
MP ................................... Evaporated type metal tape
MP ................................... Evaporated type metal tape
Table 6-3-3
Fig. 6-3-2. shows the 75% color bar signals recorded on the alignment tape.
Note:
Measure using the VIDEO terminal (Terminated at 75
Ω).
Name
Tracking
(WR5-1NP(NTSC), WR5-1CP(PAL))
(WR5-1NP(NTSC), WR5-1CP(PAL))
Video frequency characteristics
(WR5-7NE(NTSC), WR5-7CE(PAL))
(WR5-7NE(NTSC), WR5-7CE(PAL))
Operation check
(WR5-5NSP(NTSC), WR5-5CSP(PAL))
(WR5-5NSP(NTSC), WR5-5CSP(PAL))
Operation check
(WR5-8NSE(NTSC), WR5-8CSE(PAL))
(WR5-8NSE(NTSC), WR5-8CSE(PAL))
Operation check
(WR5-4NL(NTSC), WR5-4CL(PAL))
(WR5-4NL(NTSC), WR5-4CL(PAL))
Operation check
(WR5-8NLE(NTSC), WR5-8CLE(PAL))
(WR5-8NLE(NTSC), WR5-8CLE(PAL))
BPF adjustment
(WR5-11NS(NTSC), WR5-11CS(PAL))
(WR5-11NS(NTSC), WR5-11CS(PAL))
Tape speed
SP
SP (NTSC)
LP (PAL)
LP (PAL)
SP
SP
LP
LP
SP
Usage
Tape path adjustment, Switching position
adjustment
adjustment
Frequency characteristics adjustment
Operation check
BPF adjustment
Recording mode
Standard 8
Hi8
Standard 8
Hi8
Standard 8
Hi8
Standard 8
Tape type
MP
ME
MP
ME
MP
ME
MP
For NTSC model
For PAL model
Color bar signal waveform
Color bar pattern
Color bar signal waveform
Fig. 6-3-2. Color bar signal of alignment tapes
1 V
0.714 V
0.286 V
White (75%)
White (100%)
Y
ello
w
Cy
an
Green
Magenta
Red
Blue
Burst signal
0.286 V
Q
I
Horizontal sync signal
(75%)
White
Y
ello
w
Cy
an
Green
Magenta
Red
Blue
Q
I
White
(100%)
Black
1 V
0.7 V
0.3 V
White (100%)
Ye
llo
w
Cy
an
Green
Magenta
Red
Blue
Burst signal
Horizontal sync signal
0.3 V
(100%)
Ye
llo
w
Cy
an
Green
Magenta
Red
Blue
White
Blac
k
Color bar pattern
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
6-29
3-1-6.
Output Level and Impedance
S video output
4-pin mini DIN
Luminance signal:
Luminance signal:
1 Vp-p, 75
Ω, unbalanced
Chrominance signal:
CCD-TRV128/TRV228/TRV328/TRV428:
0.286 Vp-p, 75
0.286 Vp-p, 75
Ω, unbalanced
CCD-TRV228E/TRV428E:
0.3 Vp-p, 75
0.3 Vp-p, 75
Ω, unbalanced
Audio/Video output
AV MINIJACK:
VIDEO: 1 Vp-p, 75
VIDEO: 1 Vp-p, 75
Ω, unbalanced, sync negative
AUDIO: 327 mV (at output impedance more than 47 k
Ω)
Output impedance with less than 2.2 k
Ω
3-1-7.
Recording Mode (Standard 8/Hi8) switching
The record mode (Standard 8/Hi8) of this unit switches as shown
in the following table. The playback mode (Standard 8/Hi8)
switches automatically according to the recording mode of the tape
played back.
in the following table. The playback mode (Standard 8/Hi8)
switches automatically according to the recording mode of the tape
played back.
Tape Used
Recording Mode
ME
Hi8
Hi8 MP
MP
Standard 8
CCD-TRV128/TRV228/TRV228E/TRV328/TRV428/TRV428E
6-30
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENTS
1. Initialization of 8, A, C, D, E, F, 1F Page Data
If the 8, A, C, D, E, F, 1F page data is erased due to some reason,
perform “1-2. INITIALIZATION OF 8, A, C, D, E, F, 1F PAGE
DATA” of “6-1. CAMERA SECTION ADJUSTMENTS”.
perform “1-2. INITIALIZATION OF 8, A, C, D, E, F, 1F PAGE
DATA” of “6-1. CAMERA SECTION ADJUSTMENTS”.
3-3. SERVO SYSTEM ADJUSTMENTS
Before perform the servo system adjustments, check that the speci-
fied values of “28 MHz Origin Oscillation Adjustment” of “VIDEO
SYSTEM ADJUSTMENTS” is satisfied.
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
fied values of “28 MHz Origin Oscillation Adjustment” of “VIDEO
SYSTEM ADJUSTMENTS” is satisfied.
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
1. CAP FG Offset Adjustment (VC-341 board)
RadarW
RadarW
RadarW
RadarW
RadarW
Set the CAP FG signal duty cycle to 50% to establish an appropri-
ate capstan servo. If deviated, the uneven rotation of capstan and
noise can occur in the playback mode.
ate capstan servo. If deviated, the uneven rotation of capstan and
noise can occur in the playback mode.
Mode
VTR stop (PLAY/EDIT mode)
Signal
No signal
Measurement Point
Displayed data of page: 3, address: 03
Measuring Instrument
Adjusting remote commander
Adjustment Page
C
Adjustment Address
18
Specified value
The data of page: 3, address: 03 is “00”
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Adjusting method:
Order Page Address Data
Procedure
1
Close the cassette compartment
without inserting cassette.
without inserting cassette.
2
0
01
01
3
3
01
81
Press PAUSE button.
4
3
02
Check the data changes to
“00”.
“00”.
5
3
03
Check that the data is “00”.
(Note 2)
(Note 2)
6
0
01
00
Note 2:
If the data is other than “00”, adjustment has errors.
For the error contents, see the following table.
For the error contents, see the following table.
Data of page: 3,
Error contents
address: 03
01
Adjustment time out
10
Mechanism mode error (For example, the
adjustment is performed in the mode except
for VTR stop mode.)
adjustment is performed in the mode except
for VTR stop mode.)
2. Switching Position Adjustment (VC-341 board)
If deviated in this case cause switching noise or jitter on the played
back screen.
back screen.
Mode
VTR playback
Signal
Alignment tape:
For tracking adjustment
(WR5-1NP(NTSC))
(WR5-1CP(PAL))
(WR5-1NP(NTSC))
(WR5-1CP(PAL))
Measurement Point
CH1: SWP (Pin 5 of CN007)
CH2: PB RF (Pin 9 of CN007)
CH2: PB RF (Pin 9 of CN007)
Measuring Instrument
Oscilloscope
Adjustment Page
C
Adjustment Address
16, 17
Specified value
t1 = 0
± 10 µsec
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
92
Set the bit value of bit 2 to “1”,
and press PAUSE button.
(Note 2)
and press PAUSE button.
(Note 2)
3
C
16
Change the data and minimize
“t1”. (Coarse adjustment)
“t1”. (Coarse adjustment)
4
C
16
Press PAUSE button.
5
C
17
Change the data and adjust so
that the switching position (t1)
becomes specified value. (Fine
adjustment)
that the switching position (t1)
becomes specified value. (Fine
adjustment)
6
C
17
Press PAUSE button.
7
3
92
Set the bit value of bit 2 to “0”,
and press PAUSE button.
(Note 2)
and press PAUSE button.
(Note 2)
8
0
01
00
Note 2:
For the bit values, refer to “6-4. SERVICE MODE”, “4-
3. 3. Bit Value Discrimination”.
3. 3. Bit Value Discrimination”.
Fig. 6-3-3
CH1
CH2
Enlargement
t1=0
±
10
µ
sec
CH1
CH2
Click on the first or last page to see other CCD-TRV128 / CCD-TRV228 / CCD-TRV228E / CCD-TRV328 / CCD-TRV428 / CCD-TRV428E (serv.man2) service manuals if exist.