Sony CCD-TR913E / CCD-TR950E Service Manual ▷ View online
CCD-TR913E/TR950E
3-9. POWER BLOCK DIAGRAM
3-29
3-30
3-31
3-32E
CCD-TR913E/TR950E
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM-1
4-1
4-2
4-3
FRAME SCHEMATIC DIAGRAM (1/2)
CCD-TR913E/TR950E
FRAME SCHEMATIC DIAGRAM-2
4-4
4-5
4-6
FRAME SCHEMATIC DIAGRAM (2/2)
CCD-TR913E/TR950E
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(For printed wiring boards)
•
•
b
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µµ
F.
50V or less are not indicated except for electrolytics and
tantalums.
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
1
: fusible resistor
•
C
: panel designation
•
A
: B+ Line
•
B
: B– Line
•
J
: IN/OUT direction of (+,–) B LINE.
•
C
: adjustment for repair.
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the measure-
ment points and ground when camera shoots color bar chart of
pattern box. They are reference values and reference wave-
forms.
pattern box. They are reference values and reference wave-
forms.
(VOM of DC 10 M
Ω
input impedance is used.).
• Voltage values change depending upon input impedance of VOM
used.)
1. Connection
2. Adjust the distance so that the output waveform of Fig. a and
the Fig. b can be obtain.
Y
ello
w
A
A
B
B
A=B
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
Electron beam
scanned frame
scanned frame
CRT picture frame
H
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(In addition to this, the necessary note is printed in each block)
C
B
E
5
6
4
2
1
3
5
4
6
2
3
1
4
5
2
3
1
1
2
4
5
3
3
2
1
3
2
1
3
2
1
Transistor
Diode
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
When indicating parts by reference number, pleas include
the board name.
the board name.
CD-209 (CCD IMAGER) PRINTED WIRING BOARD
— Ref. No. CD-209 Board; 10,000 Series —
For printed wiring boards
• This board is six-layer print board. However, the pat-
• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included in
the diagram.
the diagram.
There are few cases that the part printed on this
diagram isn’t mounted in this model.
diagram isn’t mounted in this model.
CD-209 BOARD
C1401
A-2
C1405
A-1
C1406
A-1
C1407
B-2
C1408
B-2
C1409
B-1
C1410
B-1
C1411
B-2
C1412
B-1
CN1401 B-3
IC1401 A-3
IC1402 B-2
IC1402 B-2
L1401
A-2
L1402
B-1
R1401
A-1
R1405
A-1
R1406
B-2
R1407
B-2
R1408
B-2
R1409
B-1
CD-209
BOARD
CAMERA REC
2
IC1401
3
,
4
3
IC1401
7
4
IC1401
!™
1.1Vp-p
H
3.3Vp-p
14.187 MHz
5
IC1401
!£
,
!¢
14.187 MHz
3.7Vp-p
H
1.2Vp-p
6
IC1402
6
1
IC1401
1
,
2
6.8Vp-p
H
6.8Vp-p
H
4-7
4-8
4-9
CCD IMAGER
CD-209
Front of the lens
1.5 m
Pattern box
Note :
The components identified by mark
!
or dotted
line with mark
!
are critical for safety.
Replace only with part number specified.
CD-209
(CCD IMAGER)
(CCD IMAGER)
(TR950E)
(TR913E)
VL-25
(VIDEO LIGHT)
(VIDEO LIGHT)
MA-353
STEREO MIC AMP,
LASER LINK
STEREO MIC AMP,
LASER LINK
PJ-94
(AV IN/OUT)
(AV IN/OUT)
SE-85
(STEADY SHOT)
(STEADY SHOT)
DD-117
(DC/DC CONVERTER)
(DC/DC CONVERTER)
VF-129
(B/W EVF)
(B/W EVF)
CD-209
(CCD IMAGER)
(CCD IMAGER)
VL-25
(VIDEO LIGHT)
(VIDEO LIGHT)
MA-353
STEREO MIC AMP,
LASER LINK
STEREO MIC AMP,
LASER LINK
PJ-94
(AV IN/OUT)
(AV IN/OUT)
SE-85
(STEADY SHOT)
(STEADY SHOT)
DD-117
(DC/DC CONVERTER)
(DC/DC CONVERTER)
VF-126
(COLOR EVF)
(COLOR EVF)
Click on the first or last page to see other CCD-TR913E / CCD-TR950E service manuals if exist.