Sony CCD-TR648E / CCD-TR748E / CCD-TR848 Service Manual ▷ View online
5-7
CCD-TR648E/TR748E/TR848
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig. 5-1-5.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-5. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-5. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 5-1-6. using A0 size (1189mm
Make the chart shown in Fig. 5-1-6. using A0 size (1189mm
×
841mm) black and white vellum paper.
Fig. 5-1-6.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
adjustments without loading cassette.
1.
POWER switch (SS-2000 block) ........................... CAMERA
2.
NIGHT SHOT switch (Lens block) ................................. OFF
3.
LIGHT switch (FK-2000 block) *1 ................................. OFF
4.
DEMO MODE (Menu display) ....................................... OFF
5.
DIGITAL ZOOM (Menu display) ................................... OFF
6.
STEADY SHOT (Menu display) *2 ................................ OFF
7.
DISPLAY (Menu display) ................................. V-OUT/LCD
8.
FOCUS switch (CF-088 board) ............................ MANUAL
9.
BACK LIGHT (CF-088 board) ........................................ OFF
10. PROGRAM AE (Menu display) ...................................... OFF
11. PICTURE EFFECT (Menu display) ................................ OFF
12. 16 : 9 WIDE (MENU display) ......................................... OFF
11. PICTURE EFFECT (Menu display) ................................ OFF
12. 16 : 9 WIDE (MENU display) ......................................... OFF
*1: Video light model (CCD-TR648E/TR748E)
5-8
CCD-TR648E/TR748E/TR848
1-2.
INITIALIZATION OF D, E, F, 7 PAGE DATA
1. Initializing the D, E, F, 7 Page Data
Note1: If “Initializing the D, E, F, 7 Page Data” is performed, all
data of the D page, E page, F page and 7 page will be
initialized. (It is impossible to initialize a single page.)
initialized. (It is impossible to initialize a single page.)
Note2:
If the D, E, F, 7 page data has been initialized, “Modification of D,
E, F, 7 Page Data” and all adjustments need to be performed again.
E, F, 7 Page Data” and all adjustments need to be performed again.
Note3:
NTSC model: CCD-TR848
PAL model:
PAL model:
CCD-TR648E/TR748E
Adjusting page
D
Adjusting Address
10 to 7F
Adjusting page
F
Adjusting Address
10 to FF
Adjusting page
E
Adjusting Address
00 to FF
Adjusting page
7
Adjusting Address
00 to 6B
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
00
Set the following data.
55 (NTSC), 51 (PAL)
55 (NTSC), 51 (PAL)
3
6
01
Set the following data, and press
PAUSE button.
55 (NTSC), 51 (PAL)
PAUSE button.
55 (NTSC), 51 (PAL)
4
6
02
Check that the data changes to
“01”.
“01”.
5
2
00
29
Set the data
6
2
01
29
Set the data, and press the PAUSE
button.
button.
7
Perform “Modification of D, E, F,
7 Page Data”.
7 Page Data”.
2. Modification of D, E, F, 7 Page Data
If the D, E, F, 7 page data has been initialized, change the data of
the “Fixed data-2” address shown in the following tables by manual
input.
the “Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of D, E, F, 7 Page
data
data
Order Page Address Data
Procedure
1
2
00
29
Set the data
2
2
01
29
Set the data, and press the PAUSE
button.
button.
Note:
If the following symptoms occur after completing of the
“Modification of D, E, F, 7 page data”, check that the data of the
“Fixed data-2” addresses of D page are same as those of the same
model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD or viewfinder
“Modification of D, E, F, 7 page data”, check that the data of the
“Fixed data-2” addresses of D page are same as those of the same
model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD or viewfinder
screen is flashing.
2) The power is shut off so that unit cannot operate.
3. D Page Table
Note1:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F,
7 Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F,
7 Page Data”.)
7 Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F,
7 Page Data”.)
00 to 0F
10
11 to 12
13
14 to 1F
20
21
22
23
24 to 26
27
28 to 2D
2E
2F
30
31 to 33
34
35
36
37
38
39
3A to 3B
3C
3D
3E to 40
41
42
43
44
45
46
47
48
49
4A
4B
4C
00
Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Address
Remark
Initial data
5-9
CCD-TR648E/TR748E/TR848
4D
4E
4F
50
51 to 52
53
54
55
56 to 57
58
59
5A
5B
5C
5D to 5E
5F
60 to 72
73
74 to 7B
7C
7D to 7F
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Address
Remark
Initial data
Table. 5-1-2.
4. F Page table
Note1:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F,
7 Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F,
7 Page Data”.)
7 Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F,
7 Page Data”.)
00 to 0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E to 2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C to 3D
3E
3F
40
41
42 to 44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
00
00
00
00
00
00
00
00
00
00
00
00
52
89
88
80
7A
2B
80
65
80
8D
87
FB
33
C8
34
8C
28
07
3A
4A
12
0B
54
00
19
00
37
00
00
04
00
00
Emergency memory address
Fixed data-1
Fixed data-2
Fixed data-1
HALL adj.
Fixed data-1
AWB & LV standard data input
Auto white balance adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
28MHz origin osc. Adj.
Flange back adj.
00
00
00
00
00
00
00
00
00
00
00
00
68
80
8D
80
7A
2B
80
65
80
8D
87
FB
33
C8
34
8C
28
07
3A
4A
12
0B
54
00
19
00
37
00
00
04
00
00
Address
Remark
NTSC PAL
Initial data
5-10
CCD-TR648E/TR748E/TR848
56
57
58
59
5A
5B
5C
5D
5E
5F
60 to 61
62
63
64 to 68
69
6A to 72
73
74
75 to AE
AF
B0
B1
B2
B3 to FF
00
83
0B
00
50
68
62
B4
B4
A0
A6
80
FD
F4
0F
31
00
83
0A
00
50
62
62
D7
D7
A0
A6
80
FC
F2
11
33
Fixed data-2
Flange back adj.
CAP FG offset adj.
Switching position adj.
Fixed data-1
AFC fo adj.
Y OUT level adj.
C OUT level adj.
Fixed data-1
REC Y current adj.
Fixed data-1
REC C/AFM current adj.
Fixed data-1
1.5MHz deviation adj.
BPF fo adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Address
Remark
NTSC PAL
Table. 5-1-3.
Address
Remark
00 to 1E
1F
20 to 25
26
27 to 39
3A
3B to 42
43
44 to 51
52
53 to FF
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
5. E Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7
Page Data”.)
Table. 5-1-4.
Initial data
Click on the first or last page to see other CCD-TR648E / CCD-TR748E / CCD-TR848 service manuals if exist.