Sony SDM-X82 Service Manual ▷ View online
SDM-X82(E)
2-5
(4) Select COLOR TEMP
→
6500K in the service mode menu, and set the data
listed below as initial data for adjustment.
(5) Adjust the SUB-BRIGHTNESS: R, G, and B. Specifications are listed below.
6.
Setting for shipping
Turn off the power with the POWER button in the front panel. Check that the red
POWER LED lights on, and then execute the all mode recall. (press the POWER
button with pressing the OK button in the power-off state)
POWER LED lights on, and then execute the all mode recall. (press the POWER
button with pressing the OK button in the power-off state)
SUB-BRIGHTNESS
R
40
G
40
B
40
SUB-CONTRAST
R
130
G
130
B
130
x
y
0.313
±
0.003
Brightness (cd/m
2
)
0.329
±
0.003
14
±
0.7
2-5. Action after Replacing the LCD Panel and Board
1.
After replacing the LCD panel
(1) White balance adjustment. (Refer to Section 2-4.)
(2) CLEAR ETI TIME. (Refer to Section 2-3 step 3.)
(3) Check of picture and sound.
(2) CLEAR ETI TIME. (Refer to Section 2-3 step 3.)
(3) Check of picture and sound.
2.
After replacing the A board
(1) White balance adjustment. (Refer to Section 2-4.)
(2) EDID writing.
As the write protection is not applied in this unit, it is possible to write data
with an ordinary writing fixture.
It is required to be written for INPUT1: DVI-D, INPUT1: HD15, and
INPUT2: HD15 respectively.
Take care that the data for DVI-D and HD15 terminals are different
from each other.
(3) EDID copy to the EEPROM and ETI clear. (Refer to Section 2-1 step 6.)
Be sure to perform them after EDID writing. After executing, check
that the correct model information is displayed. (Refer to Section 2-1 step 1.)
(4) Operation check of buttons and LED's in the front panel, and Check of
picture and sound for respective inputs.
(2) EDID writing.
As the write protection is not applied in this unit, it is possible to write data
with an ordinary writing fixture.
It is required to be written for INPUT1: DVI-D, INPUT1: HD15, and
INPUT2: HD15 respectively.
Take care that the data for DVI-D and HD15 terminals are different
from each other.
(3) EDID copy to the EEPROM and ETI clear. (Refer to Section 2-1 step 6.)
Be sure to perform them after EDID writing. After executing, check
that the correct model information is displayed. (Refer to Section 2-1 step 1.)
(4) Operation check of buttons and LED's in the front panel, and Check of
picture and sound for respective inputs.
3.
After replacing the I board
(1) White balance adjustment. (Refer to Section 2-4.)
(2) Check of picture and sound.
(2) Check of picture and sound.
4.
After replacing the G board
(1) Operation check of the MAIN POWER switch.
(2) Check of picture and sound.
(2) Check of picture and sound.
5.
After replacing the H board
(1) Operation check of buttons and LED's in the front panel.
6.
After replacing the U board
(1) Check of speaker output.
(2) Check of headphone jack output.When connecting a plug to the headphone jack,
confirm no sound from the speakers.
(2) Check of headphone jack output.When connecting a plug to the headphone jack,
confirm no sound from the speakers.
SDM-X82(E) 3-1
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAMS
CN602
CN603
CN601
CN301
IC303
IC305
IC304
IC601
IC201
IC307
IC603
IC401
IC301
IC502
IC503
IC503
IC504
IC505
IC504
IC505
IC302
CN501
BOARD
I BOARD
(INVERTER)
(INVERTER)
H BOARD
(IKEY BOARD)
(IKEY BOARD)
G BOARD
(POWER)
(POWER)
A BOARD
(INTERFACE)
(INTERFACE)
SDM-X82 (E) 3-2
3-2. CIRCUIT BOARDS LOCATION
G Board
A Board
I Board
H Board
U Board
SDM-X82 (E) 3-3
3-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
•
Divided circuit diagram
One sheet of A board are circuit diagram is divided into eight sheets,
each having the code A-
a
to A-
g
. For example, the destination
ab1 on the code A-
a
sheet is connected to ab1 on the A-
b
sheet.
a b 1
Ref. No.
Circuit diagram division code
Note:
•
All capacitors are in µF unless otherwise noted. (pF: µµF)
Capacitors without voltage indication are all 50 V.
•
Indication of resistance, which does not have one for rating electrical
power, is as follows.
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP : 1/10 W)
• All resistors are in ohms.
•
: nonflammable resistor.
•
: fusible resistor.
•
∆
: internal component.
•
: panel designation, and adjustment for repair.
• All variable and adjustable resistors have characteristic curve B, unless
otherwise noted.
•
: earth-ground.
•
: earth-chassis.
• When replacing the part in below table, be sure to perform the related
adjustment.
• All voltages are in V.
• Readings are taken with a 10 M digital multimeter.
• Readings are taken with a color-bar signal input.
• Voltage variations may be noted due to normal production tolerances.
•
*
: Can not be measured.
• Circled numbers are waveform references.
•
: B + bus.
•
: B – bus.
Note: The components identified by shading and
mark
!
are critical for safety. Replace only
with part number specified.
Note: Les composants identifiés par un tramé et
une marque
!
sont critiques pour la
sécurité. Ne les remplacer que par une pièce
portant le numéro spécifié.
portant le numéro spécifié.
Click on the first or last page to see other SDM-X82 service manuals if exist.