DOWNLOAD Sony SDM-S74 / SDM-S74E / SDM-S94 Service Manual ↓ Size: 659.99 KB | Pages: 14 in PDF or view online for FREE

– 9 –

SDM-S74/S74E/S94 (E)

2) Progress upward and lifts bezel furtively and extracts

latch.

3) Progress continuously and extracts latch of bezel upper

by same method.

4) Progress continuously and extracts latch of bezel left

by same method.

5) Please pull the Rear cabinet both edge outside with

fingertips like picture, then Rear cabinet will be
departed.

6) If Rear cabinet be departed easily, please pull upside

edge of Rear cabinet outside.

 

1) Please lift the central inside edge of Front bezel

upward with fingertip like picture then latch will be
departed.

– 10 –

SDM-S74/S74E/S94 (E)

1) Enter the service mode of this unit by turning on

the power while pressing and holding the “ 

r “ key

simultaneously.

2) Press “MENU” key——MAINTAIN.
3) Press “OK” key to enter the service menu.
4) Select the desired function.
5) Press the “MENU” key to exit OSD.
6) Turn off the power and then turn on it again. The

monitor then enters the normal mode.
To enter the service again, repeat the procedure
described above.

Note
W/B readjustment is required after the panel, board
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB reset
before W/B adjustment.

1) Prepare timing and pattern data for a signal

generator according to the Sony timing
specifications.

2) Connect a monitor video cable to the signal

generator.

3) Put Color Analyzer(ex. CA-110) 50cm away from

the monitor, specify it vertically in the center of
the display, and adjust the focus to the optimum
level using an eyepiece.

4) Put the monitor and Color Analyzer(ex. CA-110)

in a light-shielded room.

5) Set up [SERVICE MODE] of the monitor.

Data is manually set to improve the productivity. The
brightness, contrast, and backlight are set to 50, 70
and 100 respectively. After that, the default data of
the color temperature to be adjusted is set.

Warm up for 30 minutes before performing any
adjustment.

a. Display SMPTE at SXGA/60Hz(Input level 0.73mV).
b. Set up [SERVICE MODE].
c. Click “INITIAL EEPROM” and again setup Service
    Mode.
d. Click “WHITE BALANCE” and then select “AUTO”.

a. Select “9300K” in “COLOR TEMP” and enter.
b. Use a 35%(89Gray) IRE white video field in the
    primary mode.
c. Adjust “SUB CONTRAST “ to secure the color

        temperature.

d. Press “MENU” key to exit adjust mode.

a. Select “6500K” in “COLOR TEMP” and enter.
b. Repeat the adjustment procedure as steps b to d
    at 9300K.

– 11 –

SDM-S74/S74E/S94 (E)

1

5

2

3

6

7

8

11

12

9

4

10

– 12 –

SDM-S74/S74E/S94 (E)

Ref. No.

 Part No.

Description

1

X-2021-045-1 BEZEL ASSY  (Gray)

BEZEL ASSY  (Black )
BEZEL ASSY  (Silver )

1-805-277-11

Panel: M170EN05-V1  (AU)

Panel: M170EN05-V5  (AU)
Panel: M170E05-L05   (CMO)

4-097-375-21 BACK CABINET (Gray)

BACK CABINET (Black )
BACK CABINET (Silver )

X-4042-062-1 STAND ASSY  (Gray)

STAND ASSY  (Black )
STAND ASSY  (Silver )

A-1410-269-A H MOUNT

6

4-096-569-01 COVER PIECE POWER SWITCH  (Gray)

COVER PIECE POWER SWITCH  (Black )
COVER PIECE POWER SWITCH  (Silver )

1-786-624-11 AC SWITCH with connector

8

A-1052-340-A G MOUNT: FSP026-2PI04OA  (AU)

G MOUNT: FSP026-2PI03OC (SPI ) (CMO)

A-1052-444-A Main board  (AU)                    V1.1,  9300, except AEP
A-1067-615-A Main board  (AU)                    V1.1AB, 6500, AEP
A-1055-495-A Main board  (CMO)                 V1.1, 9300, except AEP
A-1067-616-A Main board  (CMO)                 V1.1AB, 6500, AEP

10

1-900-275-71 Connector Assy  (COMMON)
4-097-396-01 REAR COVER  (Gray)

REAR COVER  (Black )
REAR COVER  (Silver )

4-097-399-01 ARM COVER  (REAR ) (Gray)

ARM COVER  (REAR ) (Black )
ARM COVER  (REAR ) (Silver )

4-097-386-01 CABLE HOLDER

ACCESSORIES & PACKING MATERIALS

14

1-827-757-11 D-SUB CABLE

15

1-827-758-11 DVI CABLE

16

1-827-118-11 AC Power Cord  (U/C)

AC Power Cord  (AEP )
AC Power Cord  (CH)

4-102-356-15 CD-ROM

18

19

4-103-139-02 QUICK SETUP GUIDE  (U/C, CH

QUICK SETUP GUIDE  (AEP )

4-094-401-01 PROTECTION BAG

20

4-097-408-01 CUSHION

21

4-103-571-01 INDIVIDUAL CARTON (Gray)

INDIVIDUAL CARTON (Gray),TCO'03

4-103-572-01 INDIVIDUAL CARTON (Black )

INDIVIDUAL CARTON (Silver )
INDIVIDUAL CARTON (Silver ),  TCO'03

X-2021-054-1

X-2022-009-1

2

Panel: M170EN05-V4 

1-805-277-31
1-805-600-21

3

4-097-375-31
4-097-375-41

4

X-4042-065-1
X-2022-011-1

5

4-096-569-11
4-096-569-21

7

A-

1067-595-A

G MOUNT: FSP026-2PI02 

9

11

4-097-396-11
4-097-396-21

12

4-097-399-11
4-097-399-21

13

1-827-120-11
1-827-122-11

17

4-103-139-11

4-103-573-01

2-059-676-01
2-067-031-01

(

)

AU

(CMO)

)