Sony SDM-S53 Service Manual ▷ View online
– 5 –
SDM-S53 (E)
TIMING CHART
VIDEO
SYNC
B
D
C
F
E
A
Mode
H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
720x400
70Hz
H
–
35.00
864
640
64
64
96
224
V
–
66.667Hz
525
480
3
3
39
45
640x480
60Hz
H
–
37.50
840
640
16
64
120
200
V
–
75.0Hz
500
480
1
3
16
20
640x480
65Hz
H
–
31.500
900
720
18
108
54
180
V
+
70.156Hz
449
400
12
3
34
49
640x480
75Hz
H
–
35.162
896
720
34
40
102
176
V
–
59.901Hz
587
480
12
2
93
107
720x480
60Hz
H
+-
35.156
1024
800
24
72
128
224
V
+
56.250Hz
625
600
1
2
22
25
800x600
56Hz
H
+
37.879
1056
800
40
128
88
256
V
+
60.317Hz
628
600
1
4
23
28
800x600
60Hz
H
+
48.077
1040
800
56
120
64
240
V
+
72.188Hz
666
600
37
6
23
66
800x600
72Hz
H
+
46.875
1056
800
16
80
160
256
V
+
75.0Hz
625
600
1
3
21
25
800x600
75Hz
H
–
49.727
1152
832
32
64
224
320
V
–
74.553Hz
667
624
3
3
37
43
832x624
(MAC16”)
75Hz
H
–
48.363
1328
1024
16
176
112
304
V
–
60.004Hz
816
768
8
4
36
48
1024x768
66Hz
1024x768
60Hz
H
–
56.476
1328
1024
24
136
144
304
V
–
70.069Hz
806
768
3
6
29
38
H
–
53.946
1328
1024
24
136
144
304
V
–
66.110Hz
806
768
3
6
29
38
1024x768
70Hz
H
+
60.023
1312
1024
16
96
176
288
V
+
75.029Hz
800
768
1
3
28
32
1024x768
75Hz
H
–
60.241
1328
1024
32
96
176
304
V
–
74.927Hz
804
768
3
3
30
36
1024x768
(MAC19”)
75Hz
Sync
Polarity
Frequency
Dot
Clock
Back Porch
(F)
Blanking time
(B)
Resolution
28.350
25.175
30.240
31.500
31.505
36.000
40.000
50.000
49.500
57.285
65.000
71.640
75.000
78.750
80.000
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (
µs), Vertical etc... (ms) >>
H
–
31.469
800
640
16
96
48
160
V
–
59.940Hz
525
480
10
2
33
45
Sync Duration
(D)
Front Porch
(C)
Video Active Time
(A)
Total Period
(E)
– 6 –
SDM-S53 (E)
REAR VIEW
OPERATING INSTRUCTIONS
HD15(RGB) input
connector
connector
AC IN connector
Main Power Switch
1. (Power) switch and (power) indicator
This switch turns the monitor on when the power
indicator lights up in red. To turn the monitor off, press
this switch again.
If the power indicator does not light up, press the MAIN
POWER switch.
indicator lights up in red. To turn the monitor off, press
this switch again.
If the power indicator does not light up, press the MAIN
POWER switch.
2. MENU Button
This button turns the menu screen on and off.
3.
Buttons
These buttons are used to select the menu items and
make adjustments.
make adjustments.
4. OK Button
This button actives tge selected menu item and
adjustments made using the buttons(
adjustments made using the buttons(
3
).
5. ECO Button
This button is used to reduce the power consumption.
Front Control Panel
MENU
OK
ECO
1
3
4
2
5
– 7 –
SDM-S53 (E)
1. Procedures of how to go to service mode.
1) Enter the service mode of this unit by turning on
the power while pressing and holding the “
r” key
simultaneously.
2) Press “MENU” key——MAINTAIN.
3) Press “OK” key to enter the service menu.
4) Select the desired function.
5) Press the “MENU” key to exit OSD.
6) Turn off the power and then turn on it again. The
3) Press “OK” key to enter the service menu.
4) Select the desired function.
5) Press the “MENU” key to exit OSD.
6) Turn off the power and then turn on it again. The
monitor then enters the normal mode.
To enter the service again, repeat the procedure
described above.
Note
W/B readjustment is required after the panel, board
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB reset
before W/B adjustment.
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB reset
before W/B adjustment.
2. Setup
1) Prepare timing and pattern data for a signal
generator according to the Sony timing
specifications.
specifications.
2) Connect a monitor video cable to the signal
generator.
3) Put Color Analyzer(ex. CA-110) 50cm away from
the monitor, specify it vertically in the center of
the display, and adjust the focus to the optimum
level using an eyepiece.
the display, and adjust the focus to the optimum
level using an eyepiece.
4) Put the monitor and Color Analyzer(ex. CA-110)
in a light-shielded room.
5) Set up [SERVICE MODE] of the monitor.
ADJUSTMENT
3. Operation
Data is manually set to improve the productivity. The
brightness, contrast, and backlight are set to 50, 70
and 100 respectively. After that, the default data of
the color temperature to be adjusted is set.
brightness, contrast, and backlight are set to 50, 70
and 100 respectively. After that, the default data of
the color temperature to be adjusted is set.
4. Warm up time
Warm up for 30 minutes before performing any
adjustment.
adjustment.
5. Adjustment for White Balance
a. Display SMPTE at SXGA/60Hz(Input level
0.73V).
b. Set up [SERVICE MODE].
c. Click “INITIAL EEPROM” and again setup Service
Mode.
d. Click “WHITE BALANCE” and then select “AUTO”.
0.73V).
b. Set up [SERVICE MODE].
c. Click “INITIAL EEPROM” and again setup Service
Mode.
d. Click “WHITE BALANCE” and then select “AUTO”.
6. 9300K color adjustment
a. Select “9300K” in “COLOR TEMP” and enter.
b. Use a 35%(89Gray) IRE white video field in the
primary mode.
c. Adjust “SUB CONTRAST “ to secure the color
b. Use a 35%(89Gray) IRE white video field in the
primary mode.
c. Adjust “SUB CONTRAST “ to secure the color
temperature.
d. Press “MENU” key to exit adjust mode.
7. 6500K color adjustment
a. Select “6500K” in “COLOR TEMP” and enter.
b. Repeat the adjustment procedure as steps b to d
at 9300K.
b. Repeat the adjustment procedure as steps b to d
at 9300K.
– 8 –
SDM-S53 (E)
1
2
5
3
6
7
8
11
9
4
12
10
EXPLODED VIEW
Click on the first or last page to see other SDM-S53 service manuals if exist.