DOWNLOAD Sony SDM-P82 Service Manual ↓ Size: 1.71 MB | Pages: 36 in PDF or view online for FREE

SDM-P82(E)

2-5

(4) Select COLOR TEMP 

→ 6500K in the service mode menu, and set the data

      listed below as initial data for adjustment.

(5) Adjust the SUB-BRIGHTNESS: R, G, and B. Specifications are listed below.

7.

Setting for shipping
Turn off the power with the POWER button in the front panel. Check that the red
POWER LED lights on, and then execute the all mode recall. (press the POWER
button with pressing the OK button in the power-off state)

SUB-BRIGHTNESS

R

40

G

40

B

40

SUB-CONTRAST

R

130

G

130

B

130

x

y

0.313 

± 0.003

Brightness (cd/m

2

)

0.329 

± 0.003

14 

± 0.7

1.

After replacing the LCD panel
(1) White balance adjustment. (Refer to Section 2-4.)
(2) CLEAR ETI TIME. (Refer to Section 2-3 step 3.)
(3) Check of picture and sound.

2.

After replacing the A board
(1) White balance adjustment. (Refer to Section 2-4.)
(2) EDID writing.
      As the write protection is not applied in this unit, it is possible to write data
      with an ordinary writing fixture.
      It is required to be written for INPUT1: DVI-D, INPUT1: HD15, and
      INPUT2: HD15 respectively.
      Take care that the data for DVI-D and HD15 terminals are different
      from each other.
(3) EDID copy to the EEPROM and ETI clear. (Refer to Section 2-1 step 6.)
      Be sure to perform them after EDID writing. After executing, check
      that the correct model information is displayed. (Refer to Section 2-1 step 1.)
(4) Operation check of buttons and LED's in the front panel, and Check of
      picture and sound for respective inputs.

3.

After replacing the I board
(1) White balance adjustment. (Refer to Section 2-4.)
(2) Check of picture and sound.

4.

After replacing the G board
(1) Operation check of the MAIN POWER switch.
(2) Check of picture and sound.

5.

After replacing the H board
(1) Operation check of buttons and LED's in the front panel.

SDM-P82(E)      3-1

CN602

CN603

CN601

CN301

IC303

IC305

IC304

IC601

IC201

IC307

IC603

IC401

IC301

IC502

IC503

IC503
IC504
IC505

IC302

CN501

BOARD

I BOARD
 (INVERTER)

H BOARD 
(IKEY BOARD)

G BOARD 
(POWER)

A BOARD 
(INTERFACE)

SDM-P82 (E)      3-2

G Board

A Board

I Board

H Board

SDM-P82 (E)      3-3

• Divided circuit diagram

One sheet of A board are circuit diagram is divided into eight sheets,

each having the code A-a to A-g. For example, the destination

 ab1 on the code A-a sheet is connected to  ab1 on the A-b sheet.

a   b   1

Ref. No.

Circuit diagram division code

• All capacitors are in µF unless otherwise noted. (pF:  µµF)

Capacitors without voltage indication are all 50 V.

• Indication of resistance, which does not have one for rating electrical

power, is as follows.

Pitch: 5 mm

Rating electrical power 1/4 W (CHIP : 1/10 W)

• All resistors are in ohms.

•

: nonflammable resistor.

•

: fusible resistor.

•

∆

: internal component.

•

: panel designation, and adjustment for repair.

• All variable and adjustable resistors have characteristic curve B, unless

otherwise noted.

•

: earth-ground.

•

: earth-chassis.

• When replacing the part in below table, be sure to perform the related

adjustment.

• All voltages are in V.

• Readings are taken with a 10 M  digital multimeter.

• Readings are taken with a color-bar signal input.

• Voltage variations may be noted due to normal production tolerances.

•

*

: Can not be measured.

• Circled numbers are waveform references.

•

: B + bus.

•

: B – bus.

! are critical for safety. Replace only

! sont critiques pour la