DOWNLOAD Sony SDM-N50PS Service Manual ↓ Size: 3.82 MB | Pages: 56 in PDF or view online for FREE

2-2

1

 Two copper foil tapes

2

 Two screws

3

 Shield case

CN501

CN508

CN507

4

 Two screws

Pan head screw
M 1.6

5

 Jack panel

6

 B board

LCD module (TFT)

Cushion

(

)

2

 Earth (H)

2

 Earth (H)

3

 Cover holder

CN501

4

 Washer (H)

5

 H board

6

 BH1 harness assembly

LCD module (TFT)

Cushion

1

 Three screws

(+BVTP3x6)

2

 Panel tape

Front cover assembly

Cushion

1

 Remove the LCD module (TFT) in the

derecition of allow 

A

 horizontally.            

A

*Remove the B and H boards refering 2-3 and 2-4.

2-3

b

c

a

1

 

Four screws

(+TP 3x5)

2

 

Two earth wires

3

 

Two connectors

(CN703, CN704)

Chassis plate assembly

5

 

Remove the terminal board assembly

in the direction of allow 

b

.

6

 

Remove the G board in the

direction of allow 

c

.

4

 

Remove the case in the

direction of allow 

a

.

CN703

CN704

* Remove A board refering 2-6.

CN705

CN701

CN702

1

 Four sheets (G)

2

 Four screws

(+BVTP  3x12)

5

 Three screws (+TP 3x5)

6

 Three connectors

(CN705, CN701, CN702)

4

 For screws (HD 15)

7

 A board

3

 Case (L)

3-1

Connect the personal computer, monitor, and signal generator as shown below, and control the monitor.

•

Confirm the screen by below three kinds of the modes
within preseted frequency.

Signal mode
1.

MODE  0 (640X480 60Hz)

2.

MODE 10 (800X600 75Hz)

3.

MODE 17 (1024X768 75Hz)

(1) Input a cross hatch signal.
(2) Confirm both edges can see or white lines of edges are not

separating from indicated area edges.
Errors in the range of 2dot are permit.
Be saticefy one of both edges that is within above
specification.

•

When no measuring instrument is used, compare the color
with the reference set so that the colors will be the same.

1.

Adjustment of 9300°K

(1) Confirm every R/G/B_USER_BKG are initialized value.
(2) Receive MODE 15 (1024X768 60Hz) 80IRE.

Set COLOR to 9300°K. (COLOR_INDEX=1)

(3) Make adjustment with R/G_USR_DRV to set the

chromaticity within the specification.

y adjustment ..... Make adjustment with B_USR_DRV.

(Also x value changes simultaneous)

B_USR_DRV  UP

Values x and y decrease.

B_USR_DRV  DOWN

Values x and y increase.

x adjustment ..... Make adjustment with R_USR_DRV.

R_USR_DRV  UP

Value y increases.

R_USR_DRV  DOWN

Value y decreases.

Adjust again and bring down G_USR_DRV 10 STEP to
become within the specification ; however, in case of
adjustment range of y value become deficientlly and when
B_USR_DRV=255.

(4) Make the signal 30IRE all white to check that it is within the

specification.

(5) Adjust R/B_USER_BKG to become within the specification

when (4) deviates the specification.

(6) Input a grayscale and perform picture quality confirmation.

(7) Perform color save ( select C with ALT+M ).

Spec: 9300°K  80IRE (x, y) = (0.285, 0.294)

Within 3JND

9300°K  30IRE (x, y) = (0.265, 0.268)

Within 4JND

Note: Make adjustment up to ±0.002.

2.

Adjustment of 6500°K

(1) Confirm every R/G/B_USER_BKG are initialized value.
(2) Receive MODE 15 (1024X768 60Hz) 80IRE.

Set COLOR to 6500°K.  (COLOR_INDEX=2)

(3) Make adjustment with R/G_USR_DRV to set the chromaticity

within the specification.

y adjustment ..... Make adjustment with B_USR_DRV.

(Also x value changes simultaneous)

B_USR_DRV  UP

Values x and y decrease.

B_USR_DRV  DOWN

Values x and y increase.

x adjustment ..... Make adjustment with R_USR_DRV.

R_USR_DRV  UP

Value y increases.

R_USR_DRV  DOWN

Value y decreases.

Adjust again and bring down G_USR_DRV 10 STEP to
become within the specification ; however, in case of
adjustment range of y value become deficientlly and when
B_USR_DRV=255.

(4) Make the signal 30IRE all white to check that it is within the

specification.

(5) Adjust R/B_USER_BKG to become within the specification

when (4) deviates the specification.

(6) Input a grayscale and perform picture quality confirmation.
(7) Perform color save ( select C with ALT+M ).

Spec: 6500°K  80IRE (x, y) = (0.314, 0.324)

Within 3JND

6500°K  30IRE (x, y) = (0.295, 0.305)

Within 4JND

Note: Make adjustment up to ±0.002.

Computer for jig

1-690-391-21
Cord,Connection

D-sub
(9 pin [female])

mini Din
(8 pin)

1

A-1500-819-A
Interface Unit

SDM-N50

2

3

Connector
Attachment

Box Unit

Signal generator
(VG-823, etc.)

TO
INPUT-1

4 pin

4 pin

6 pin
To CN107 Connector
(A board)

* The parts above (     ~     ) are necessary for DAS adjustment.

1

3

1-900-255-59
Connector Assy

3-2

3.

Adjustment of 5000°K

(1) Confirm every R/G/B_USER_BKG are initialized value.
(2) Receive MODE 15 (1024X768 60Hz) 80IRE.

Set COLOR to 5000°K. (COLOR_INDEX=3)

(3) Make adjustment with R/G_USR_DRV to set the chromaticity

within the specification.

y adjustment ..... Make adjustment with B_USR_DRV.

(Also x value changes simultaneous)

B_USR_DRV  UP

Values x and y decrease.

B_USR_DRV  DOWN

Values x and y increase.

x adjustment ..... Make adjustment with R_USR_DRV.

R_USR_DRV  UP

Value y increases.

R_USR_DRV  DOWN

Value y decreases.

Adjust again and bring down G_USR_DRV 10 STEP to
become within the specification ; however, in case of
adjustment range of y value become deficientlly and when
B_USR_DRV=255.

(4) Make the signal 30IRE all white to check that it is within the

specification.

(5) Adjust R/B_USER_BKG to become within the specification

when (4) deviates the specification.

(6) Input a grayscale and perform picture quality confirmation.
(7) Perform color save ( select C with ALT+M ).

Spec: 5000°K  80IRE (x, y) = (0.345, 0.352)

Within 3JND

5000°K  30IRE (x, y) = (0.322, 0.332)

Within 4JND

Note: Make adjustment up to ±0.002.position.