DOWNLOAD Sony GDM-F500 Service Manual ↓ Size: 6.23 MB | Pages: 58 in PDF or view online for FREE

•

1. Enter the full white signal. (or the full black dots signal).
2. Adjust the contrast to the maximum.
3. Make the screen monogreen.
Note: Off the outputs from R ch and B ch of SG.
4. Reverse the DY, and adjust coarsely the purity magnet so

that a green raster positions in the center of screen.

5. Adjust the tilt of DY, and fix lightly with a clamp.
Note: “TILT” shall be set at 128.

•

1. Put the set inside the Helmholtz coil. (“LCC SW” = “12”)
2. Input the single green signal and set the CONT control to

MAX.

Note: After the W/B adjustment with 9300K, measure an aver-

age of 

Σ

Ik when a full white signal is entered in the CONT

MAX/BRT CENT status. Then make adjustment so that
the specified screen can be attained after aging for 2 hours
with Ik equivalent to 30% of the average value.

3. Demagnetize the metal part of the chassis with the hand de-

gausser and coil degausser, and the CRT surface with the
hand degausser.
Input AC 230V to AC IN, turn on and off the power to per-
form auto degaussing. (Perform auto degaussing by setting
“MON CON REG2”=152. Return to the original value after
use.)
Demagnetize the CRT surface with the hand degausser
again.

Note:
(1) Hand degauss must be used on stand-by or power-off condi-

tion.
This model has an automatic earth magnetism correction
function by using an earth magnetism sensor and a LCC coil.
When using a hand degauss while monitor (LCC coil) is be-
ing operated, it sometimes gets magnetized, and the system
may not work properly as a result.

(2) Adjust in a non-magnetic field. BV=45uT.
(3) If adjusting in a magnetic fields, add the shift from the non-

magnetic field in your estimation.

4. Attach the wobbling coil to the designated part of the CRT

neck.

5. Attach the sensor of the landing adjustment unit on the CRT

surface.

6. Adjust the DY position and purity, and the DY tilt, and land-

ing of the center and 4 corners with the landing checker.

•

Write terrestrial magnetism sensor reading VX and VY to
“LCC VX” and LCC VY” respectively. Adjust the land-
ing by moving “LCC NS”, “LCC LT”, “LCC LB”, “LCC
RT” and “LCC RB”. However, the register adjustment
must be limited within the following range.
“LCC NS”

128 ± 15

“LCC LT”, “LCC LB”, “LCC RT”, “LCC RB”

128 ± 40

After adjustment, set “LCC SW” to “13” and save the ser-
vice data.

 ± 6

 ± 6

 ± 6

 ± 6

 ± 4

 ± 6

 ± 6

 ± 6

 ± 6

<Specifications>
Adjust so that the green is within
the specification given right.
Adjust target : within ± 1

The red and blue must be within
the specification given right with
respect to the green.

A difference between red and blue
must be within the specification
given right.

0 ± 3 0 ± 7.5 0 ± 3

0 ± 5 0 ± 5

0 ± 5

0 ± 3 0 ± 7.5 0 ± 3

(µm)

(µm)

10

10

10

10

7

10

10

10

10

(µm)

* Adjustment and measurement should be made at the points

one inch inside the fluorescent screen.

7. Insert wedges to make the DY neck stand upright without

moving it.
At this time, without shaking the DY, firmly insert the
wedges.

8. Check the landing of each corner, and if it does not satisfy

the specification, adjust the landing of four corners using
“LCC LT“, “LCC LB”, “LCC RT” and “LCC RB”.
However, the register adjustment must be limited within the
following range.

“LCC NS”

128 ± 15

“LCC LT”, “LCC LB”, “LCC RT”, “LCC RB”

128 ± 40

After adjustment, save the service data.
If it does not yet satisfy the specification, paste a Disk-Mg
onto the funnel and adjust.

Note:
(1) Do not paste more than two magnets on one corner.
(2) Magnets will be placed in a range 80 ~ 100 mm from the DY

along diagonal lines.

(3) After placing magnets, absolutely hand degauss and check

the results.  (Hand degauss must be used on stand-by or
power-off condition.)

9. Remove the sensor and wobbling coil.
10. Switch the signal to R.G.B., and check that each color is

pure.

11. Check that the DY is not tilting, and fix the purity Mg with a

white pen.

4-1

Connect the communication cable of the computer to the connector located on the D board or US board on the monitor.  Run the service
software and then follow the instruction.

IBM AT Computer

as a Jig

1-690-391-21

1

A-1500-819-A
Interface Unit

2

*The parts above (                ) are necessary for DAS adjustment.

1

3

D-sub
(9 Pin [female])

mini Din
(8Pin)

4 Pin

3-702-691-01
Connector Attachment

3

To BUS CONNECTOR

or

4 Pin

4 Pin

•

(1) Receive an image of the white crosshatch signals (white

lines on black).

(2) Place the protrusions of the 6-fold poles magnet attached to

the CRT neck upon each other. (Fig. 1)

(3) Make rough adjustment of the H and V direction conver-

gence by using 4-fold poles magnet.

* Set so that the protruding parts of

the 2 magnet rings agree with
each other.

•

1. 9300K

x=0.283 ± 0.005
y=0.298 ± 0.005

(All White)

2. 6500K

x=0.313 ± 0.005
y=0.329 ± 0.005

(All White)

3. 5000K

x=0.346 ± 0.005
y=0.359 ± 0.005

(All White)

•

•

Adjust the focus volume 1 and 2 for the optimum focus.

•

4-2

B

A

C

Bezel opening

Picture

fH

60kHz

60kHz

A Zone

0.24 mm

0.24 mm

B Zone

0.28 mm

0.32 mm

C Zone

0.32 mm

0.36 mm

B

a

a     3.2 mm
b     3.2 mm

a

b

b

A

MODE

A

B

388 mm

291 mm

3

364 mm

291 mm

1, 2, 4, 5

TLH correction plate (Put in one side only)

XBV
XCV
APH

YBH
YCH
TLV







Protrusions

60

°

Fig. 1

Fig. 3

Fig. 2

*

XBV

XCV

B

R

B

R

R
B

B
R

R

B

B

R 

TLV

TLH

YBH

YCH

R B

R B

Focus 2

Focus 1

HDK

5-1

5-2

5-3

5-4