DOWNLOAD Sony CPD-E240 / CPD-E440 Service Manual ↓ Size: 1.08 MB | Pages: 22 in PDF or view online for FREE

4-087-422-12(1)

© 2002 Sony Corporation

â

CPD-E240 CPD-E440

4-087-422-12 (1)

Operating Instructions 

Mode d’emploi 

Manual de instrucciones 

E:\desktop stuff\E240E440\4087422121\US\01GB01COV-AEP.fm

01GB01COV-AEP.book  Page 1  Tuesday, March 26, 2002  4:32 PM

2

E:\desktop stuff\E240E440\4087422121\US\01GB02GET-AEP.fm

CPD-E240 CPD-E440

4-087-422-12 (1)

The model and serial numbers are located at the rear of the unit. 
Record these numbers in the spaces provided below. Refer to them 
whenever you call upon your dealer regarding this product.
Model No.                         Serial No.                          

This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly 
approved in this manual could void your authority to operate this 
equipment.

Sony de Tijuana Este S.A. de C.V.
Laguna Mainar No. 5520, Seccion C
Parque Industrial El Lago
Tijuana, B.C. Mexico C.P. 22570
Tel. (664) 6-25-32-16, RFC STE-961001-959

Sony Electronicos de Mexico, S.A. de C.V.
Henry Ford No. 29
Fraccionamiento Industrial San Nicolas
Tlalnepantla, Estado de Mexico C.P. 54030
Tel. (55) 3-21-10-00, RFC SEM-941001-BJA

INFORMATION
This product complies with Swedish National Council for Metrology 
(MPR) standards issued in December 1990 (MPR II) for very low 
frequency (VLF) and extremely low frequency (ELF).

INFORMATION
Ce produit est conforme aux normes du Swedish National Council 
for Metrology de décembre 1990 (MPR II) en ce qui concerne les 
fréquences très basses (VLF) et extrêmement basses (ELF).

INFORMACIÓN
Este producto cumple las normas del Consejo Nacional Sueco 
para MetrologÍa (MPR) emitidas en diciembre de 1990 (MPR II) 
para frecuencias muy bajas (VLF) y frecuencias extremadamente 
bajas (ELF).

For questions regarding your product or for the Sony Customer 
Information Service Center nearest you call:

The number below is for FCC related matters only.

Para prevenir cualquier mal funcionamiento y evitar daños, por 
favor, lea detalladamente este manual de instrucciones antes de 
conectar y operar este equipo.

This notice is applicable for USA/Canada only.
If shipped to USA/Canada, install only a UL LISTED/CSA 
LABELLED power supply cord meeting the following 
specifications:
SPECIFICATIONS

Plug Type

Nema-Plug 5-15p

Cord 

Type SVT or SJT, minimum 3 

× 18 AWG

Length

Maximum 15 feet

Rating

Minimum 7 A, 125 V

Cette notice s’applique aux Etats-Unis et au Canada 
uniquement.
Si cet appareil est export* aux Etats-Unis ou au Canada, utiliser 
le cordon d’alimentation portant la mention UL LISTED/CSA 
LABELLED et remplissant les conditions suivantes:
SPECIFICATIONS

Type de fiche

Fiche Nema 5-15 broches

Cordon

Type SVT ou SJT, minimum 3 

× 18 AWG

Longueur

Maximum 15 pieds

Tension

Minimum 7 A, 125 V

As an 

E

NERGY 

S

TAR Partner, Sony 

Corporation has determined that this 
product meets the 

E

NERGY 

S

TAR 

guidelines for energy efficiency.

Trade Name:

Sony

Model No.:

CPD-E240 and CPD-E440

Responsible Party:

Sony Electronics Inc.

Address:

680 Kinderkamack Road, Oradell, 
NJ 07649 USA

Telephone No.:

201-930-6972

This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions:  (1) This device may not 
cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation.

01GB01COV-AEP.book  Page 2  Tuesday, March 26, 2002  4:32 PM

3

E:\desktop stuff\E240E440\4087422121\US\01GB03BAS-AEP.fm

CPD-E240 CPD-E440

4-087-422-12 (1)

• Trinitron

â

 and FD Trinitron

â 

are registered trademarks of Sony 

Corporation.

• Macintosh is a trademark licensed to Apple Computer, Inc., registered in 

the U.S.A. and other countries.

• Windows

â

 and MS-DOS are registered trademarks of Microsoft 

Corporation in the United States and other countries.

• IBM PC/AT and VGA are registered trademarks of IBM Corporation of 

the U.S.A.

• VESA and DDC

ä

 are trademarks of the Video Electronics Standard 

Association.

•

E

NERGY 

S

TAR is a U.S. registered mark.

• All other product names mentioned herein may be the trademarks or 

registered trademarks of their respective companies.

• Furthermore, “

ä” and “â” are not mentioned in each case in this manual.

• Use the supplied power cord. If you use a different power cord, 

be sure that it is compatible with your local power supply.
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will not 
conform to mandatory FCC standards.

• Before disconnecting the power cord, wait at least 30 seconds 

after turning off the power to allow the static electricity on the 
screen’s surface to discharge.

• After the power is turned on, the screen is demagnetized 

(degaussed) for about 5 seconds. This generates a strong 
magnetic field around the screen which may affect data stored on 
magnetic tapes and disks placed near the monitor. Be sure to keep 
magnetic recording equipment, tapes, and disks away from the 
monitor.

Installation
Do not install the monitor in the following places:
• on surfaces (rugs, blankets, etc.) or near materials (curtains, 

draperies, etc.) that may block the ventilation holes

• near heat sources such as radiators or air ducts, or in a place 

subject to direct sunlight

• in a place subject to severe temperature changes
• in a place subject to mechanical vibration or shock
• on an unstable surface
• near equipment which generates magnetism, such as a 

transformer or high voltage power lines

• near or on an electrically charged metal surface
• in a dusty or smoky environment
• inside an enclosed rack

• The screen’s surface is covered with a thin anti-reflective coating 

to enhance the ergonomic characteristics of the monitor. To ensure 
that the coating is not damaged, use a soft cloth to clean the 
screen’s surface. If necessary, use a soft cloth lightly moistened 
with a mild detergent solution, such as hand soap, to wipe the 
screen. 

• Do not use any type of abrasive pad, alkaline cleanser, scouring 

powder, or solvents such as alcohol or benzene as they might 
damage the anti-reflective coating.

•  If you use a glass cleaning liquid, do not use any type of cleaner 

containing an anti-static solution or similar additive as this may 
scratch the screen’s coating.

• Do not rub, touch, or tap the surface of the screen with sharp or 

abrasive items such as a ballpoint pen or screwdriver. This type of 
contact may result in a scratched picture tube.

• Clean the cabinet, panel and controls with a soft cloth lightly 

moistened with a mild detergent solution. 

• Do not use any type of abrasive pad, scouring powder or solvent, 

such as alcohol or benzene.

When you transport this monitor for repair or shipment, use the 
original carton and packing materials.

Do not remove this monitor’s stand.

This monitor can be adjusted within the 
angle shown in the picture to the right. 
To turn the monitor vertically, hold it at 
the bottom with both hands. Be careful 
not to pinch your fingers at the back of 
the monitor when you tilt the monitor up 
vertically.

Protection
• Do not put foreign objects into the 

monitor.

• Disconnect the monitor if environment exceeds 60°C/140°F.
• Ensure AC power cord is not trapped under furniture, TV, etc.
• Do not overload wall outlets, extension cords, or convenience 

receptacles beyond their capacity.

• Never spill liquid of any kind on the monitor.

Preset mode timing table . . . . . . . . . . . . . . . . . . . . .  i

Contacting Sony. . . . . . . . . . . . . . . . . . . . . . . . . . . .  i

The equipment should be installed near an easily accessible 
outlet.

Example of plug types

for 100 to 120 V AC

15°

90°

5°

90°

Centering line

01GB03BAS-AEP.fm  Page 3  Thursday, April 11, 2002  12:35 PM

4

E:\desktop stuff\E240E440\4087422121\US\01GB03BAS-AEP.fm

CPD-E240 CPD-E440

4-087-422-12 (1)

When connecting this monitor to a Macintosh computer, use a 
Macintosh adapter (not supplied) if necessary. Connect the 
Macintosh adapter to the computer before connecting the cable. 

* DDC (Display Data Channel) is a standard of VESA.

1

This monitor complies with the “DDC” Plug & Play standard and 
automatically detects all the monitor’s information. No specific driver 
needs to be installed to the computer.
The first time you turn on your PC after connecting the monitor, the setup 
Wizard may appear on the screen. In this case, follow the on-screen 
instructions. The Plug & Play monitor is automatically selected so that you 
can use this monitor.

• Do not touch the pins of the video signal cable connector.
• Check the alignment of the HD15 connector to prevent bending the pins 

of the video signal cable connector.

m/M to highlight the main menu that  

m/M to highlight the submenu that 

</, to 

Brightness and contrast adjustments are made using a separate 
BRIGHTNESS/CONTRAST menu. These adjustments are 
effective for all input signals.

m/M to adjust the brightness (

</, to adjust the contrast ( ).

If you set the brightness and contrast level to “0”, the picture will black out 
and no picture will appear.

Video signal cable
of the monitor

to HD15 of the 
connecting computer

5

4

3

2

1

6

7 8 9 10

11 12 13 14 15

1

Red

2

Green (Sync on 
Green)

3

Blue

4

ID (Ground)

5

DDC Ground*

6

Red Ground

7

Green Ground

8

Blue Ground

9

DDC HOST 5V*

10

Ground

11

ID (Ground)

12

Bi-Directional 
Data (SDA)*

13

H. Sync

14

V. Sync

15

Data Clock 
(SCL)*

,

68 . 7 kHz / 85Hz

1024 768

the horizontal
and vertical 
frequencies 
of the current 
input signal

the resolution of the current 
input signal (only if the signal 
matches to one of the 
recommended VESA timing 
modes).

Main menu

MENU

Sub menu

2 6

S I ZE / CENTER

MENU

b

5 0

1 0 0

BR I GHTNESS / CONTRAS T

01GB01COV-AEP.book  Page 4  Tuesday, March 26, 2002  4:32 PM