DOWNLOAD Sony CPD-E100 / CPD-E100E / CPD-E100P Service Manual ↓ Size: 4.16 MB | Pages: 40 in PDF or view online for FREE

Model
CPD-E100 CPD-E100E CPD-E100P
Pages
40
Size
4.16 MB
Type
PDF
Document
Service Manual
Brand
Device
Monitor / S/M CPD-E100/E/P 99 US CAN
File
cpd-e100-cpd-e100e-cpd-e100p.pdf
Date

Sony CPD-E100 / CPD-E100E / CPD-E100P Service Manual ▷ View online

CPD-E100/E100E/E100P
– 3 –
LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part hav-
ing a return to chassis, must not exceed 0.5 mA (500
microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instruments.
2. A battery-operated AC milliammeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all
battery operated digital multimeters that have a 2 V AC
range are suitable.  (See Fig. A)
WARNING!!
NEVER TURN ON THE POWER IN A CONDITION IN
WHICH THE DEGAUSS COIL HAS BEEN REMOVED.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
¡
 ON THE SCHEMATIC DIAGRAMS, EXPLODED
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR
SAFE OPERATION. REPLACE THESE COMPONENTS
WITH SONY PARTS WHOSE PART NUMBERS AP-
PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-
MENTS PUBLISHED BY SONY. CIRCUIT ADJUST-
MENTS THAT ARE CRITICAL FOR SAFE OPERATION
ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE
PROCEDURES WHENEVER CRITICAL COMPONENTS
ARE REPLACED OR IMPROPER OPERATION IS SUS-
PECTED.
AVERTISSEMENT!!
NE JAMAIS METTRE SOUS TENSION QUAND LA
BOBINE DE DEMAGNETISATION EST ENLEVÉE.
ATTENTION AUX COMPOSANTS RELATIFS À LA
SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET
UNE MARQUE 
¡
 SONT CRITIQUES POUR LA SÉCURITÉ.
NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE
NUMÉRO SPECIFIÉ.  LES RÉGLAGES DE CIRCUIT DONT
L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT SONT IDENTIFIÉS DANS LE
PRÉSENT MANUEL.  SUIVRE CES PROCÉDURES LORS
DE CHAQUE REMPLACEMENT  DE COMPOSANTS CRI-
TIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENT
EST SUSPECTÉ.
After correcting the original service problem, perform the fol-
lowing safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly tran-
sistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values.
Make sure your instruments are accurate; be suspicious of
your HV meter if sets always have low HV.
8. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
Leakage. Check leakage as described below.
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY  CHECK-OUT
1.5 k
0.15 
µ
F
AC
Voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
CPD-E100/E100E/E100P
– 4 –
TABLE  OF  CONTENTS
Section
Title
Page
1. GENERAL
.................................................................. 1-1
2. DISASSEMBLY
2-1.
Cabinet Removal ................................................. 2-1
2-2.
A and D Boards Removal ................................... 2-1
2-3.
H Board Removal ................................................. 2-1
2-4.
Picture Tube Removal .......................................... 2-2
2-5.
Harnes Location ................................................... 2-3
3. SAFETY  RELATED  ADJUSTMENT
............. 3-1
4. ADJUSTMENTS
...................................................... 4-1
5. DIAGRAMS
5-1.
Block Diagrams ................................................... 5-1
5-2.
Circuit Boards Location ...................................... 5-5
5-3.
Schematic Diagrams and Printed Wiring Boards ...... 5-6
(1) Schematic Diagram of A Board ........................... 5-7
(2) Schematic Diagram of D Board .......................... 5-11
(3) Schematic Diagram of H Board .......................... 5-19
5-4. Semiconductors ................................................... 5-21
6. EXPLODED  VIEWS
6-1.
Chassis ................................................................. 6-1
6-2.
Packing Materials ................................................ 6-2
7. ELECTRICAL  PARTS  LIST
............................ 7-1
1-1
SECTION 1
GENERAL
The operating instructions mentioned here are partial abstracts 
from the Operating Instruction Manual.  The page numbers of 
the Operating Instruction Manual remein as in the manual.
4
Precautions
Warning on power connections
• Use the supplied power cord. If you use a different power cord, 
be sure that it is compatible with your local power supply.
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will not 
conform to mandatory FCC standards.
• Before disconnecting the power cord, wait at least 30 seconds 
after turning off the power to allow the static electricity on the 
screen’s surface to discharge.
• After the power is turned on, the screen is demagnetized 
(degaussed) for about 5 seconds. This generates a strong 
magnetic field around the screen which may affect data stored 
on magnetic tapes and disks placed near the monitor. Be sure to 
keep magnetic recording equipment, tapes, and disks away 
from the monitor.
Installation
Do not install the monitor in the following places:
• on surfaces (rugs, blankets, etc.) or near materials (curtains, 
draperies, etc.) that may block the ventilation holes
• near heat sources such as radiators or air ducts, or in a place 
subject to direct sunlight
• in a place subject to severe temperature changes
• in a place subject to mechanical vibration or shock
• on an unstable surface
• near equipment which generates magnetism, such as a 
transformer or high voltage power lines
• near or on an electrically charged metal surface
Maintenance
• Clean the screen with a soft cloth. If you use a glass cleaning 
liquid, do not use any type of cleaner containing an anti-static 
solution or similar additive as this may scratch the screen’s 
coating.
• Do not rub, touch, or tap the surface of the screen with sharp or 
abrasive items such as a ballpoint pen or screwdriver. This type 
of contact may result in a scratched picture tube.
• Clean the cabinet, panel and controls with a soft cloth lightly 
moistened with a mild detergent solution. Do not use any type 
of abrasive pad, scouring powder or solvent, such as alcohol or 
benzene.
Transportation
When you transport this monitor for repair or shipment, use the 
original carton and packing materials.
Use of the tilt-swivel
This monitor can be adjusted within the angles shown below. To 
find the center of the monitor’s turning radius, align the center of 
the monitor’s screen with the centering dots on the stand.
Hold the monitor at the bottom with both hands when you turn it 
horizontally or vertically. Be careful not to pinch your fingers at 
the back of the monitor when you tilt the monitor up vertically.
The equipment should be installed near an easily accessible 
outlet.
Example of plug types
for 100 to 120 V AC
for 200 to 240 V AC
90˚
90˚
15˚
Centering dots
5
US
Identifying parts and controls
See the pages in parentheses for further details.
1
RESET button (page 12)
This button resets the adjustments to the factory settings.
2
Control button (page 9)
The control button is used to display the menu and make 
adjustments to the monitor, including brightness and contrast 
adjustments.
3 1
 (power) switch and indicator (pages 7, 13, 16)
This button turns the monitor on and off. The power indicator 
lights up in green when the monitor is turned on, and either 
flashes in green and orange, or lights up in orange when the 
monitor is in power saving mode.
4
AC IN connector (page 6)
This connector provides AC power to the monitor.
5
Video input connector (HD15) (page 6)
This connector inputs RGB video signals (0.700 Vp-p, 
positive) and sync signals.
* DDC (Display Data Channel) is a standard of VESA.
AC  IN
MENU
RESET
MENU
RESET
Rear
Front
Pin No.
Signal
1
Red
2
Green
(Sync on Green)
3
Blue
4
ID (Ground)
5
DDC Ground*
6
Red Ground
7
Green Ground
8
Blue Ground
9
10
Ground
11
ID (Ground)
12
Bi-Directional Data (SDA)*
13
H. Sync
14
V. Sync
15
Data Clock (SCL)*
1 2
3 4 5
8
7
6
11 12 13 14 15
10
9
1-2
6
Setup
Before using your monitor, check that the following accessories 
are included in your carton:
• Power cord (1)
• Windows Monitor Information Disk (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)
Step 1: Connect your monitor to 
your computer
Turn off the monitor and computer before connecting.
Note
Do not touch the pins of the video cable connector as this might bend the 
pins.
x
Connecting to an IBM PC/AT or compatible 
computer
x
Connecting to a Macintosh or compatible 
computer 
Step 2: Connect the power cord
With the monitor and computer switched off, first connect the 
power cord to the monitor, then connect it to a power outlet.
AC  IN
IBM PC/AT or 
compatible computer
to video output
AC  IN
You will need a Macintosh adapter (not supplied).
Macintosh adapter (not supplied)
to video output
Macintosh or 
compatible computer
AC  IN
to AC IN
to a power outlet
power cord (supplied)
7
US
Step 3: Turn on the monitor and 
computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen
• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, confirm that 
your computer’s graphic board is completely seated in the 
correct bus slot. 
• If you are replacing an old monitor with this model and OUT 
OF SCAN RANGE appears on the screen, reconnect the old 
monitor. Then adjust the computer’s graphic board so that the 
horizontal frequency is between 30 – 70 kHz, and the vertical 
frequency is between 48 – 120 Hz.
For more information about the on-screen messages, see “Trouble 
symptoms and remedies” on page 14.
For customers using Windows 95/98
To maximize the potential of your monitor, install the new model 
information file from the supplied Windows Monitor Information Disk 
onto your PC.
This monitor complies with the “VESA DDC” Plug & Play standard. If 
your PC/graphics board complies with DDC, select “Plug & Play Monitor 
(VESA DDC)” or this monitor’s model name as the monitor type in the 
“Control Panel” of Windows 95/98. If your PC/graphics board has 
difficulty communicating with this monitor, load the Windows Monitor 
Information Disk and select this monitor’s model name as the monitor 
type.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 is different from Windows 95/98 and 
does not involve the selection of monitor type. Refer to the Windows 
NT4.0 instruction manual for further details on adjusting the resolution, 
refresh rate, and number of colors.
Adjusting the monitor’s resolution and color number
Adjust the monitor’s resolution and color number by referring to your 
computer’s instruction manual. The color number may vary according to 
your computer or video board. The color palette setting and the actual 
number of colors are as follows:
• High Color (16 bit) 
t 65,536 colors
• True Color (24 bit) 
t about 16.77 million colors
In true color mode (24 bit), speed may be slower.
Selecting the on-screen menu 
language (LANGUAGE/
INFORMATION)
English, French, German, Italian, Spanish, Russian and Japanese 
versions of the on-screen menus are available. The default setting 
is English.
1
Press the center of the control button.
See page 9 for more information on using the control button.
2
Move the control button 
m
/
M
 to highlight 
 
LANGUAGE/INFORMATION and press the center of 
the control button again.
3
Move the control button 
m
/
M
 to select 
 
(LANGUAGE) and move 
<
/
,
 to select a language.
• ENGLISH
• FRANÇAIS: French
• DEUTSCH: German
• ITALIANO: Italian
• ESPAÑOL: Spanish
: Russian
: Japanese 
To close the menu
Press the center of the control button once to return to the main MENU, 
and press again selecting EXIT to return to normal viewing. If no buttons 
are pressed, the menu closes automatically after about 30 seconds.
To reset to English
Press the RESET button while the 
 (LANGUAGE) menu is displayed 
on the screen.
MENU
EX I T
H - S I Z E / CENT ER
V - S I Z E / CENT ER
P I N / P I N BA L ANCE
KEY / KEY BA L ANCE
ROT A T I ON
ZOOM
COLOR
SE L ECT
L ANGUAGE / I NFORMA T
N
O
I
DEGAUSS / CANCE L MO
E
R
I
MENU
MENU
ENGL I SH
FRANÇA I S
DEUT SCH
I T A L I ANO
ESPAÑOL
SE L ECT
EX I T
LANGUAGE / I NFORMAT I ON
Page of 40
Display

Sony CPD-E100 / CPD-E100E / CPD-E100P Service Manual ▷ Download

  • DOWNLOAD Sony CPD-E100 / CPD-E100E / CPD-E100P Service Manual ↓ Size: 4.16 MB | Pages: 40 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony CPD-E100 / CPD-E100E / CPD-E100P in PDF for free, which will help you to disassemble, recover, fix and repair Sony CPD-E100 / CPD-E100E / CPD-E100P Monitor. Information contained in Sony CPD-E100 / CPD-E100E / CPD-E100P Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.