Sony CPD-200GS Service Manual ▷ View online
1-2
7
Getting Started
F
EN
ES
C
Getting Started
Connecting Your Monitor’s
Speaker
Speaker
You can listen to music, sounds, and other audio files using
the speaker in your monitor.
Connect the AUDIO IN jack to the audio out jack of your
computer’s sound card using the miniplug cord (supplied).
the speaker in your monitor.
Connect the AUDIO IN jack to the audio out jack of your
computer’s sound card using the miniplug cord (supplied).
Adjusting the sound
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “™
SOUND,” and press the MENU button again.
The SOUND OSD appears.
SOUND,” and press the MENU button again.
The SOUND OSD appears.
Note
While muting the sound, the
While muting the sound, the
mark appears in the SOUND OSD
instead of the Á mark. Increase the volume to cancel the
mark
and activate the speaker.
3
Press the >?// buttons to adjust the volume.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
To mute the sound
Press the MUTING button.
No sound comes from the speaker.
The
No sound comes from the speaker.
The
mark appears at the bottom of the screen.
To cancel, press the MUTING button again.
Using the headphones jack
You can listen to the audio signals from your computer
using headphones (not supplied). The speaker turns off
when headphones are connected to the headphones jack.
Adjust the volume using the SOUND OSD.
using headphones (not supplied). The speaker turns off
when headphones are connected to the headphones jack.
Adjust the volume using the SOUND OSD.
Note
If the volume from the speaker is too low, increase the output level
(average of 500 mv) of the computer.
If the volume from the speaker is too low, increase the output level
(average of 500 mv) of the computer.
AUDIO
IN
AUDIO IN jack
2
Headphones jack
MENU
EXIT
CENTER
SIZE
GEOM
COLOR
SOUND
ZOOM
SCREEN
OPTION
OK
MENU
MENU
SOUND
26
MUTING
6
Getting Started
to video output
to video output
About the supplied Macintosh adapter
The supplied Macintosh adapter is compatible with Macintosh LC,
Performa, Quadra and Power Macintosh series computers.
Macintosh II series and some older versions of Power Book models
may need an adapter with micro switches (not supplied).
The supplied Macintosh adapter is compatible with Macintosh LC,
Performa, Quadra and Power Macintosh series computers.
Macintosh II series and some older versions of Power Book models
may need an adapter with micro switches (not supplied).
Note
Do not short the pins of the video signal cable.
Do not short the pins of the video signal cable.
Step 2: Connect the power cord
With the monitor switched off, connect one end of the
power cord to the monitor and the other end to a power
outlet.
power cord to the monitor and the other end to a power
outlet.
Step 3: Turn on the monitor and computer
The installation of your monitor is complete.
Note
If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on
the screen, see “Warning Messages” on page 18.
If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on
the screen, see “Warning Messages” on page 18.
For customers using Windows 95
Install the new model information from the “Windows 95 Monitor
Information Disk” into your PC. (Refer to the attached Windows 95
Monitor Information Disk manual.)
Install the new model information from the “Windows 95 Monitor
Information Disk” into your PC. (Refer to the attached Windows 95
Monitor Information Disk manual.)
This monitor complies with the “VESA DDC” Plug&Play standard.
If your PC/graphics board complies with DDC, select “Plug and
Play Monitor (VESA DDC)” as “Monitor type” from “Control
Panel” in Windows 95. Some PCs/graphics boards do not comply
with DDC. Even if your computer complies with DDC, it may have
some problems connecting with this monitor. In this case, select this
monitor‘s model name (CPD-100GS or CPD-200GS) as “Monitor
type” in Windows 95.
If your PC/graphics board complies with DDC, select “Plug and
Play Monitor (VESA DDC)” as “Monitor type” from “Control
Panel” in Windows 95. Some PCs/graphics boards do not comply
with DDC. Even if your computer complies with DDC, it may have
some problems connecting with this monitor. In this case, select this
monitor‘s model name (CPD-100GS or CPD-200GS) as “Monitor
type” in Windows 95.
Selecting the On-screen Display
Language
Language
If you need to change the OSD language, see “Selecting the
on-screen display language” on page 15.
The default setting is English.
on-screen display language” on page 15.
The default setting is English.
to a power outlet
Power cord (supplied)
Macintosh adapter
(supplied)
(supplied)
IBM PC/AT or
compatible computer
compatible computer
Macintosh or
compatible computer
compatible computer
to AC IN
Setup
Before using this monitor, check that the following items are
included in your carton:
• Monitor (1)
• Power cord (1)
• Macintosh adapter (1)
• Windows
included in your carton:
• Monitor (1)
• Power cord (1)
• Macintosh adapter (1)
• Windows
®
95 Monitor Information Disk and its manual
(1)
• Warranty card (1)
• These operating instructions (1)
• Audio miniplug cord (1)
• These operating instructions (1)
• Audio miniplug cord (1)
This monitor works with any IBM or compatible system
equipped with VGA or greater graphics capability.
Although this monitor works with other platforms running
at horizontal frequencies between 30 and 70 kHz (CPD-
100GS), 30 and 85 kHz (CPD-200GS), including Macintosh
and Power Macintosh systems, a cable adapter is required.
Please consult your dealer for advice on which adapter is
suitable for your needs.
equipped with VGA or greater graphics capability.
Although this monitor works with other platforms running
at horizontal frequencies between 30 and 70 kHz (CPD-
100GS), 30 and 85 kHz (CPD-200GS), including Macintosh
and Power Macintosh systems, a cable adapter is required.
Please consult your dealer for advice on which adapter is
suitable for your needs.
Step 1: Connect the monitor to the
computer
Connecting to an IBM PC/AT, Macintosh or
compatible computer
compatible computer
With the computer switched off, connect the video signal
cable to the computer’s video output.
cable to the computer’s video output.
1-3
9
Getting Started
F
EN
ES
C
Customizing Your Monitor
Using the CENTER On-screen
Display
Display
The CENTER settings allow you to adjust the centering of
the picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
the picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
CENTER,” and press the MENU button again.
The CENTER OSD appears.
CENTER,” and press the MENU button again.
The CENTER OSD appears.
3
For horizontal adjustment
Press the >?// buttons.
Press the >?// buttons.
/ . . . to move the picture right
? . . . to move the picture left
? . . . to move the picture left
For vertical adjustment
Press the ¨./> buttons.
Press the ¨./> buttons.
> . . . to move the picture up
. . . . to move the picture down
. . . . to move the picture down
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The horizontal and vertical centerings are both reset to the
factory settings.
The horizontal and vertical centerings are both reset to the
factory settings.
Using the SIZE On-screen Display
The SIZE settings allow you to adjust the size of the picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
SIZE,” and press the MENU button again.
The SIZE OSD appears.
SIZE,” and press the MENU button again.
The SIZE OSD appears.
3
For horizontal adjustment
Press the >?// buttons.
Press the >?// buttons.
/ . . . to increase picture size
? . . . to decrease picture size
? . . . to decrease picture size
For vertical adjustment
Press the ¨./> buttons.
Press the ¨./> buttons.
> . . . to increase picture size
. . . . to decrease picture size
. . . . to decrease picture size
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The horizontal and vertical sizes are both reset to the factory
settings.
The horizontal and vertical sizes are both reset to the factory
settings.
MENU
MENU
SIZE
26
73
CENTER
26
73
8
Customizing Your Monitor
Introducing the On-screen
Display System
Display System
Most adjustments are made using the MENU OSD.
MENU OSD
Press the MENU button to display the MENU OSD.
This MENU OSD contains links to the other OSDs described
below.
This MENU OSD contains links to the other OSDs described
below.
1
COLOR
Displays the COLOR OSD for adjusting the color
temperature.
temperature.
2
CENTER
Displays the CENTER OSD for adjusting the centering
of the picture.
of the picture.
3
SCREEN
Displays the SCREEN OSD for adjusting the vertical
and horizontal convergence, etc.
and horizontal convergence, etc.
4
ZOOM
Displays the ZOOM OSD for enlarging and reducing
the picture.
the picture.
5
OPTION
Displays the OPTION OSD for adjusting the OSD
position, degaussing the screen, selecting the OSD
language, etc.
position, degaussing the screen, selecting the OSD
language, etc.
6
SIZE
Displays the SIZE OSD for adjusting the picture size.
7 ™ SOUND
Displays the SOUND OSD for adjusting the sound.
8
GEOM
Displays the GEOMETRY OSD for adjusting the picture
rotation and pincushion, etc.
rotation and pincushion, etc.
9 EXIT
Closes the MENU OSD.
MENU
MENU
EXIT
CENTER
SIZE
GEOM
COLOR
SOUND
ZOOM
SCREEN
OPTION
OK
MENU
Before adjusting
• Connect the monitor and the computer, and turn them on.
• Select “
• Select “
(LANGUAGE)” in the OPTION OSD, then
select “ENG” (English) (see page 15).
Adjusting the Picture Brightness
and Contrast
and Contrast
Once the setting is adjusted , it will be stored in memory for
all input signals received.
all input signals received.
1
Press the ¨ (brightness) ./> or > (contrast) ?//
buttons.
The BRIGHTNESS/CONTRAST OSD appears.
buttons.
The BRIGHTNESS/CONTRAST OSD appears.
2
For brightness adjustment
Press the ¨./> buttons.
Press the ¨./> buttons.
> . . . for more brightness
. . . . for less brightness
. . . . for less brightness
For contrast adjustment
Press the >?// buttons.
Press the >?// buttons.
/ . . . for more contrast
? . . . for less contrast
? . . . for less contrast
The OSD automatically disappears after about 3 seconds.
To reset, press the RESET button while the OSD is on. The
brightness and contrast are both reset to the factory settings.
brightness and contrast are both reset to the factory settings.
*
The horizontal and vertical frequencies for the received input
signal appear in the BRIGHTNESS/CONTRAST OSD.
signal appear in the BRIGHTNESS/CONTRAST OSD.
Horizontal
Frequency*
Frequency*
Vertical
Frequency*
Frequency*
Customizing Your Monitor
BRIGHTNESS/CONTRAST
26
26
60.0kHz/ 85Hz
1-4
10
Customizing Your Monitor
Using the GEOM (Geometry) On-
screen Display
screen Display
The GEOM (geometry) settings allow you to adjust the
shape and orientation of the picture.
Once the rotation is adjusted, it will be stored in memory for
all input signals received. All other adjustments will be
stored in memory for the current input signal.
shape and orientation of the picture.
Once the rotation is adjusted, it will be stored in memory for
all input signals received. All other adjustments will be
stored in memory for the current input signal.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
GEOM,” and press the MENU button again.
The GEOMETRY OSD appears.
GEOM,” and press the MENU button again.
The GEOMETRY OSD appears.
3
Press the ¨./> buttons to select the item you want
to adjust.
to adjust.
Select
ROTATION
PINCUSHION
PIN BALANCE
KEYSTONE
KEY BALANCE
To
adjust the picture rotation
adjust the picture sides
adjust the picture side balance
adjust the picture width
adjust the picture shape balance
4
Press the >?// buttons to adjust the settings.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The selected item is reset to the factory setting.
The selected item is reset to the factory setting.
For
ROTATION
PINCUSHION
PIN BALANCE
KEYSTONE
KEY BALANCE
Press
/ . . . to rotate the picture clockwise
? . . . to rotate the picture counterclockwise
/ . . . to expand the picture sides
? . . . to contract the picture sides
/ . . . to move the picture sides to the right
? . . . to move the picture sides to the left
/ . . . to increase the picture width at the
top
? . . . to decrease the picture width at the
top
/ . . . to move the top of the picture to
the right
? . . . to move the top of the picture to
the left
MENU
ROTATION
GEOMETRY
26
11
Getting Started
Customizing Your Monitor
F
EN
ES
C
Using the ZOOM On-screen
Display
Display
The ZOOM settings allow you to enlarge or reduce the
picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
ZOOM,” and press the MENU button again.
The ZOOM OSD appears.
ZOOM,” and press the MENU button again.
The ZOOM OSD appears.
3
Press the >?//buttons to adjust the picture zoom.
/ . . . to enlarge the picture
? . . . to reduce the picture
? . . . to reduce the picture
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
Note
The picture zoom adjustment will stop as soon as either the
horizontal or vertical size reaches its maximum or minimum value.
The picture zoom adjustment will stop as soon as either the
horizontal or vertical size reaches its maximum or minimum value.
Using the COLOR On-screen
Display
Display
You can change the monitor’s color temperature. For
example, you can change the colors of a picture on the
screen to match the actual colors of the printed picture.
Once the setting is adjusted, it will be stored in memory for
all input signals received.
example, you can change the colors of a picture on the
screen to match the actual colors of the printed picture.
Once the setting is adjusted, it will be stored in memory for
all input signals received.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
COLOR,” and press the MENU button again.
The COLOR OSD appears.
COLOR,” and press the MENU button again.
The COLOR OSD appears.
If you are using Graphic Picture Enhancement (GPE)
If you are in one of the GPE modes, the following
COLOR OSD appears when “
If you are in one of the GPE modes, the following
COLOR OSD appears when “
COLOR” is selected.
This OSD allows you to reduce the color temperature
from 11,000K to 9,300K. Press the >?// buttons to
adjust the color temperature.
from 11,000K to 9,300K. Press the >?// buttons to
adjust the color temperature.
For more information on using GPE, see “Selecting the
Graphic Picture Enhancement (GPE) Mode” on page 16.
Graphic Picture Enhancement (GPE) Mode” on page 16.
ZOOM
73
V
26
H
MENU
MENU
9300K
5000K
5000K
COLOR
(continued)
COLOR
26
1-5
13
Getting Started
Customizing Your Monitor
F
EN
ES
C
4
Press the >?// buttons to adjust the settings.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The selected item is reset to the factory setting.
The selected item is reset to the factory setting.
For
H CONVERGENCE
V CONVERGENCE
CANCEL MOIRE
MOIRE ADJUST
Using the OPTION On-screen
Display
Display
The OPTION OSD allows you to manually degauss the
screen and adjust settings such as the OSD position and
OSD language. It also allows you to lock the controls.
screen and adjust settings such as the OSD position and
OSD language. It also allows you to lock the controls.
Degaussing the screen
The monitor screen is automatically degaussed
(demagnetized) when the power is turned on.
You can also manually degauss the monitor.
(demagnetized) when the power is turned on.
You can also manually degauss the monitor.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
OPTION,” and press the MENU button again.
The OPTION OSD appears.
OPTION,” and press the MENU button again.
The OPTION OSD appears.
3
Press the ¨./> buttons to select “
(MANUAL
DEGAUSS).”
4
Press the > / button.
The screen is degaussed for about 5 seconds.
The screen is degaussed for about 5 seconds.
If you need to degauss the screen a second time, wait for at
least 20 minutes before repeating the steps above.
least 20 minutes before repeating the steps above.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the MENU button again.
seconds.
To close the OSD, press the MENU button again.
MENU
ON
OFF
ON
OFF
Press
/ . . . to shift red shadows to the right
and blue shadows to the left
? . . . to shift red shadows to the left
and blue shadows to the right
/ . . . to shift red shadows up and blue
shadows down
? . . . to shift red shadows down and
blue shadows up
/ . . . to turn CANCEL MOIRE “ON”
? . . . to turn CANCEL MOIRE “OFF”
/ . . . to increase the moire cancellation
effect
? . . . to decrease the moire cancellation
effect
50
0
MANUAL DEGAUSS
OPTION
ON
12
Customizing Your Monitor
Using the SCREEN On-screen
Display
Display
Adjust convergence settings to eliminate red or blue
shadows that may appear around objects on the screen.
Adjust the CANCEL MOIRE function to eliminate wavy or
elliptical lines that may appear on the screen.
Once the setting is adjusted, it will be stored in memory for
all input signals received.
shadows that may appear around objects on the screen.
Adjust the CANCEL MOIRE function to eliminate wavy or
elliptical lines that may appear on the screen.
Once the setting is adjusted, it will be stored in memory for
all input signals received.
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ¨./> and >?// buttons to select “
SCREEN,” and press the MENU button again.
The SCREEN OSD appears.
SCREEN,” and press the MENU button again.
The SCREEN OSD appears.
3
Press the ¨./> buttons to select the item you want
to adjust.
to adjust.
Select
H CONVERGENCE
V CONVERGENCE
CANCEL MOIRE
*
MOIRE ADJUST
To
adjust the horizontal convergence
adjust the vertical convergence
eliminate elliptical or wavy lines on
the screen
the screen
adjust the degree of moire
cancellation
cancellation
*
CANCEL MOIRE must be “ON” for “
(MOIRE ADJUST)”
to appear on the screen.
MENU
3
Press the ¨./> buttons to select the color
temperature.
temperature.
There are two color temperature modes in the OSD.
The preset adjustments are 9,300K and 5,000K.
The preset adjustments are 9,300K and 5,000K.
Selecting your own color temperature between
9,300K and 5,000K
Press the ¨./> buttons to select “
9,300K and 5,000K
Press the ¨./> buttons to select “
(VARIABLE)”
and adjust by pressing the >?// buttons.
/ . . . for a higher temperature (bluish)
? . . . for a lower temperature (reddish)
? . . . for a lower temperature (reddish)
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on. The
selected color temperature is reset to the factory settings.
selected color temperature is reset to the factory settings.
9300K
5000K
5000K
COLOR
VARIABLE
50
H CONVERGENCE
SCREEN
26
Click on the first or last page to see other CPD-200GS service manuals if exist.