Sony DVP-S9000ES Service Manual ▷ View online
6-3
(5-4) AVdec DREQ
Matching check of 5-3 executed via DMA
(5-5) AVdec Interrupt
Data transfer to AVD RAM via DMA
→
interrupt detec-
tion check
(5-6) AVdec Revision
AVD revision (chip and uCode) display. Error is not de-
tected.
tected.
(5-7) AVdec Reset
Data write
→
no reset data
6. OSD (IC802)
(6-2) OSD Register
(6-3) OSD DRAM
(6-4) OSD Download
(6-5) OSD Interrupt
(6-6) OSD Reset
7. FBI, SACD
(7-2) FBI Register & DRAM (IC702)
Data writing to FBI DRAM
→
read matching check
(7-3) FBI Interrupt
FBI DVA interrupt detection check
(7-4) FBI Reset
Nothing is done. *Executed only for the serial interface.
(7-5) SACD Register & DRAM (IC901)
DRAM of SACD is checked, and whether the checking has
successfully completed is detected.
successfully completed is detected.
8. Video
(8-2) Venc Video Out
Venc (IC106) color bar command write
→
Video OUT
Error: Not detected.
The command is transferred to the Venc, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/C,
Component) except EURO AV terminal.
The command is transferred to the Venc, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/C,
Component) except EURO AV terminal.
(8-3) OSC (check)
→
Video
OSD blue screen display About 1.5 seconds
(8-4) FBI (check)
→
Video
FBI multi screen display (9-screen frame) About 1.5 sec-
onds
onds
(8-5) AVdec_DRAM
→
Video
AVD gradation display (color patterns) About 1.5 seconds
(8-6) ARP_DRAM
→
Video
Display with ARP color bar data About 1.5 seconds
(8-7) Progre Video Out
Output of ARP color bar data for Progre About 3 seconds
(8-8) Euro Model Check (AEP, UK model)
Composite Out
EURO-AV Composite video output check
AVD color bar command write
EURO-AV Composite video output check
AVD color bar command write
→
Video (EURO-AV Com-
posite) OUT
Error: Not detected.
With the Component of video output turned off, the color
bar signals are output from the EURO-AV terminal.
Error: Not detected.
With the Component of video output turned off, the color
bar signals are output from the EURO-AV terminal.
Y/C Out
EURO-AV Y/C video output check
AVD color bar command write
EURO-AV Y/C video output check
AVD color bar command write
→
Video (EURO-AV Y/C)
OUT
Error: Not detected.
With the Y/C of video output turned on, the color bar sig-
nals are output from the EURO-AV terminal.
Error: Not detected.
With the Y/C of video output turned on, the color bar sig-
nals are output from the EURO-AV terminal.
RGB Out
EURO-AV RGB video output check
AVD color bar command write
EURO-AV RGB video output check
AVD color bar command write
→
Video (EURO-AV RGB)
OUT
Error: Not detected.
With the RGB of video output turned on, the color bar sig-
nals are output from the EURO-AV terminal.
Error: Not detected.
With the RGB of video output turned on, the color bar sig-
nals are output from the EURO-AV terminal.
Component Out
EURO-AV Component video output check
AVD color bar command write
EURO-AV Component video output check
AVD color bar command write
→
Video (EURO-AV Com-
ponent) OUT
Error: Not detected.
With the Component of video output turned on, the color
bar signals are output from the EURO-AV terminal.
Error: Not detected.
With the Component of video output turned on, the color
bar signals are output from the EURO-AV terminal.
Euro AV Through
Euro-AV2 input check.
Check video and audio signal pass through from Euro-AV2
to Euro-AV1.
Error: Not detected.
Euro-AV2 input check.
Check video and audio signal pass through from Euro-AV2
to Euro-AV1.
Error: Not detected.
9. Audio
(9-2) Analog Out (Dac/Dout)
AC3 data output
→
Three-time beeping
Check first beep for 0dB, second beep for –6dB, and third
beep for 0dB.
beep for 0dB.
(9-3) Analog Out (L/R Check)
None
(9-4) SF 44.1 kHz (16.9344 MHz)
Observe the IC103 pin 7 on the AU-226 board with the
oscilloscope to check for the frequency and waveform.
oscilloscope to check for the frequency and waveform.
(9-5) SF 48.0 kHz (18.4320 MHz)
Observe the IC103 pin 7 on the AU-226 board with the
oscilloscope to check for the frequency and waveform.
oscilloscope to check for the frequency and waveform.
Nothing is done.
*OSD check is executed.
(Serial interface only)
*OSD check is executed.
(Serial interface only)
6-4
Check Items List
2. ROM, Model, Region
(2-2) ROM Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
(2-2) ROM Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
3. RAM, EEPROM, NFLASH, H2GA
(3-2) RAM write/read
(3-3) EEPROM write/read
(3-4) NAND FLASH write/read
(3-5) H2GA Register
(3-6) H2GA Interrupt
(3-7) H2GA Reset
(3-2) RAM write/read
(3-3) EEPROM write/read
(3-4) NAND FLASH write/read
(3-5) H2GA Register
(3-6) H2GA Interrupt
(3-7) H2GA Reset
4. Servo, ARP
(4-2) Servo-DSP Driver Test
(4-3) Servo-DSP Register
(4-4) Servo-DSP Reset
(4-5) ARP Register
(4-6) ARP DRAM
(4-7) ARP Reset
(4-8) ARP Interrupt
(4-2) Servo-DSP Driver Test
(4-3) Servo-DSP Register
(4-4) Servo-DSP Reset
(4-5) ARP Register
(4-6) ARP DRAM
(4-7) ARP Reset
(4-8) ARP Interrupt
5. AV Decoder
(5-2) AVdec Register
(5-3) AVdec DRAM
(5-4) AVdec DREQ
(5-5) AVdec Interrupt
(5-6) AVdec Revision
(5-7) AVdec Reset
(5-2) AVdec Register
(5-3) AVdec DRAM
(5-4) AVdec DREQ
(5-5) AVdec Interrupt
(5-6) AVdec Revision
(5-7) AVdec Reset
6. OSD
(6-2) OSD Register
(6-3) OSD DRAM
(6-4) OSD Download
(6-5) OSD Interrupt
(6-6) OSD Reset
(6-2) OSD Register
(6-3) OSD DRAM
(6-4) OSD Download
(6-5) OSD Interrupt
(6-6) OSD Reset
7. FBI, SACD
(7-2) FBI Register & DRAM
(7-3) FBI Interrupt
(7-4) FBI Reset
(7-5) SACD Register & DRAM
(7-2) FBI Register & DRAM
(7-3) FBI Interrupt
(7-4) FBI Reset
(7-5) SACD Register & DRAM
8. Video
(8-2) Venc Video Out
(8-3) OSD (check)
(8-2) Venc Video Out
(8-3) OSD (check)
→
Video
(8-4) FBI (check)
→
Video
(8-5) AVdec_DRAM
→
Video
(8-6) ARP_DRAM
→
Video
(8-7) Progre Video Out
(8-8) Composite Out
(8-9) Y/C Out
(8-10) RGB Out
(8-11) Component Out
(8-12) Euro AV Through
(8-8) Composite Out
(8-9) Y/C Out
(8-10) RGB Out
(8-11) Component Out
(8-12) Euro AV Through
9. Audio
(9-2) Analog Out (Dac/Dout)
(9-3) Analog Out (L/R Check)
(9-4) SF 44.1 kHz (16.9344 MHz)
(9-5) SF 48.0 kHz (18.4320 MHz)
(9-2) Analog Out (Dac/Dout)
(9-3) Analog Out (L/R Check)
(9-4) SF 44.1 kHz (16.9344 MHz)
(9-5) SF 48.0 kHz (18.4320 MHz)
Error Codes List
00: Error not detected
30: RAM write/read data discord
31: EEPROM NG
32: Flash memory clear error
33: Flash memory write error
34: Flash memory read data discord
35: H2GA Register
36: H2GA Interrupt
37: H2GA Reset
40: Servo DSP NG
41: ARP register read data discord
42: ARP
30: RAM write/read data discord
31: EEPROM NG
32: Flash memory clear error
33: Flash memory write error
34: Flash memory read data discord
35: H2GA Register
36: H2GA Interrupt
37: H2GA Reset
40: Servo DSP NG
41: ARP register read data discord
42: ARP
←→
RAM data bus error
43: ARP
←→
RAM address bus error
44: ARP RAM read data discord
45: ARP Interrupt NG
46: ARP Reset NG
50: AVD Register NG
51: AVD DRAM NG
52: AVD DRAM_DMA NG
53: AVD Reset NG
60: OSD Register NG
61: OSD DRAM NG
62: OSD Initial NG
63: OSD Interrupt NG
70: FBI Register & DRAM NG
71: FBI Interrupt NG
72: FBI Initial NG
73: SACD Register Error
74: SACD DRAM CHECK Error
80: ARP
45: ARP Interrupt NG
46: ARP Reset NG
50: AVD Register NG
51: AVD DRAM NG
52: AVD DRAM_DMA NG
53: AVD Reset NG
60: OSD Register NG
61: OSD DRAM NG
62: OSD Initial NG
63: OSD Interrupt NG
70: FBI Register & DRAM NG
71: FBI Interrupt NG
72: FBI Initial NG
73: SACD Register Error
74: SACD DRAM CHECK Error
80: ARP
→
1930 video NG
90: ARP
→
1930 audio NG
A0: System call error (function not supported)
A1: System call error (parameter error)
A2: System call error (illegal ID number)
A3: System call error (time out)
A4: NAND Flash faulty blocks exceed 10
F0: Error occurred
F1: User verification NG
F2: Diagnosis cancelled
A1: System call error (parameter error)
A2: System call error (illegal ID number)
A3: System call error (time out)
A4: NAND Flash faulty blocks exceed 10
F0: Error occurred
F1: User verification NG
F2: Diagnosis cancelled
6-5
6-4.
DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press
[1]
key on the remote com-
mander, and the drive auto adjustment menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
4. SACD
Exit: RETURN
Normally,
[0]
is selected to adjust DVD (single layer), CD, DVD
(dual layer), and SACD in this order. But, individual items can be
adjusted for the case where adjustment is suspended due to an
error. In this mode, the adjustment can be made easily through the
operation following the message displayed on the screen.
The disc used for adjustment must be the one specified for adjust-
ment. However, for SACD disc, use the player with initial data if
the disc is not available.
adjusted for the case where adjustment is suspended due to an
error. In this mode, the adjustment can be made easily through the
operation following the message displayed on the screen.
The disc used for adjustment must be the one specified for adjust-
ment. However, for SACD disc, use the player with initial data if
the disc is not available.
0. ALL
You will be asked if EEPROM data are initialized or not, and for
this prompt, select
this prompt, select
[0]
and press the
[ENTER]
key, and the servo
set data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2.
CD disc, 3. DVD-DL disc, and 4. SACD disc are adjusted in this
order. Each time one disc was adjusted, it is ejected. Replace it
with the specified disc following the message. Though the mes-
sage to confirm whether discs other than SACD disc are adjusted
is not displayed, you can finish the adjustment if pressing the
CD disc, 3. DVD-DL disc, and 4. SACD disc are adjusted in this
order. Each time one disc was adjusted, it is ejected. Replace it
with the specified disc following the message. Though the mes-
sage to confirm whether discs other than SACD disc are adjusted
is not displayed, you can finish the adjustment if pressing the
[ ]
button. The S curve level, RF level, and jitter value can be con-
firmed during adjustment, and if OK, press the
firmed during adjustment, and if OK, press the
[ENTER]
key and
continue adjustment. (If NG, press the
[ ]
button) During adjust-
ment of each disc, the measurement for disc type judgment is made.
As automatic adjustment does not judge the disc type unlike con-
ventional models, take care not to insert wrong type discs. Also,
do not give a shock during adjustment.
As automatic adjustment does not judge the disc type unlike con-
ventional models, take care not to insert wrong type discs. Also,
do not give a shock during adjustment.
1. DVD-SL (single layer)
Select
[1]
, insert DVD single layer disc, and press
[ENTER]
key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
adjusted values will be written to the EEPROM.
DVD Single Layer Disc Adjustment Steps
1. Sled Tilt Reset
2. Disc Check Memory SL
3. Wait 500 msec
4. Set Disc Type SL
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Search ON
9. Focus Search OFF
10. Focus Servo ON 1
11. Auto Track Offset Adjust
12. Tracking ON
13. CLVA ON
14. Wait 1 sec
15. Sled ON
16. Check CLV Lock
17. Auto Loop Filter Offset Adjust
18. Auto Focus Offset Adjust
19. Auto Tilt Position Adjust
20. Auto Focus Gain Adjust
21. Auto Focus Offset Adjust
22. EQ Boost Adjust
23. Auto Loop Filter Offset Adjust
24. Auto Track Gain Adjust
25. All Servo Stop
26. Eep Copy Loop Filter Offset
1. Sled Tilt Reset
2. Disc Check Memory SL
3. Wait 500 msec
4. Set Disc Type SL
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Search ON
9. Focus Search OFF
10. Focus Servo ON 1
11. Auto Track Offset Adjust
12. Tracking ON
13. CLVA ON
14. Wait 1 sec
15. Sled ON
16. Check CLV Lock
17. Auto Loop Filter Offset Adjust
18. Auto Focus Offset Adjust
19. Auto Tilt Position Adjust
20. Auto Focus Gain Adjust
21. Auto Focus Offset Adjust
22. EQ Boost Adjust
23. Auto Loop Filter Offset Adjust
24. Auto Track Gain Adjust
25. All Servo Stop
26. Eep Copy Loop Filter Offset
x
x
6-6
2. CD
Select
[2]
, insert CD disc, and press
[ENTER]
key, and the adjust-
ment will be made through the following steps, then adjusted val-
ues will be written to the EEPROM.
ues will be written to the EEPROM.
CD Adjustment Steps
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Search ON
9. Focus Search OFF
10. Focus Servo ON 1
11. Auto Track Offset Adjust
12. Tracking ON
13. (TC Display Start)
14. CLVA ON
15. Wait 1 sec
16. Jitter Display Start
17. Sled ON
18. Check CLV ON
19. Auto Loop Filter Offset Adjust
20. Auto Focus Offset Adjust
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto Loop Filter Offset Adjust
25. Auto Track Gain Adjust
26. All Servo Stop
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Search ON
9. Focus Search OFF
10. Focus Servo ON 1
11. Auto Track Offset Adjust
12. Tracking ON
13. (TC Display Start)
14. CLVA ON
15. Wait 1 sec
16. Jitter Display Start
17. Sled ON
18. Check CLV ON
19. Auto Loop Filter Offset Adjust
20. Auto Focus Offset Adjust
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto Loop Filter Offset Adjust
25. Auto Track Gain Adjust
26. All Servo Stop
3. DVD-DL (dual layer)
Select
[3]
, insert DVD dual layer disc, and press
[ENTER]
key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
adjusted values will be written to the EEPROM.
DVD Dual Layer Disc Adjustment Steps
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec
Layer 1 Adjust
8. Focus Servo ON 1
9. Auto Track Offset Adjust L1
10. Tracking ON
11. CLVA ON
12. Wait 1 sec
13. Sled ON
14. Check CLV Lock
15. Auto Loop Filter Offset Adjust
16. Auto Focus Offset Adjust
17. Auto Focus Gain Adjust
18. Auto Focus Offset Adjust
19. Eq Boost Adjust
20. Auto Loop Filter Offset
21. Auto Track Gain Adjust
9. Auto Track Offset Adjust L1
10. Tracking ON
11. CLVA ON
12. Wait 1 sec
13. Sled ON
14. Check CLV Lock
15. Auto Loop Filter Offset Adjust
16. Auto Focus Offset Adjust
17. Auto Focus Gain Adjust
18. Auto Focus Offset Adjust
19. Eq Boost Adjust
20. Auto Loop Filter Offset
21. Auto Track Gain Adjust
Layer 0 Adjust
22. Fj (L1
→
L0)
23. Auto Track Offset Adjust L0
24. Tracking ON
25. CLVA ON
26. Wait 1 sec
27. Sled ON
28. Check CLV Lock
29. Auto Loop Filter Offset Adjust
30. Auto Focus Offset Adjust
31. Auto Focus Gain Adjust
32. Auto Focus Offset Adjust
33. Eq Boost Adjust
34. Auto Loop Filter Offset
35. Auto Track Gain Adjust
36. All Servo Stop
24. Tracking ON
25. CLVA ON
26. Wait 1 sec
27. Sled ON
28. Check CLV Lock
29. Auto Loop Filter Offset Adjust
30. Auto Focus Offset Adjust
31. Auto Focus Gain Adjust
32. Auto Focus Offset Adjust
33. Eq Boost Adjust
34. Auto Loop Filter Offset
35. Auto Track Gain Adjust
36. All Servo Stop
Click on the first or last page to see other DVP-S9000ES service manuals if exist.