DOWNLOAD Sony DVP-S7700 (serv.man2) Service Manual ↓ Size: 43.72 MB | Pages: 127 in PDF or view online for FREE

Etc

90:

Fail in servo recovery when starting up the disc.

91:

Took more than 30 seconds when starting up the
disc.

92:

The number of the times of  servo error at re-
covery is over regulation.

96:

Auto Sequence Time Out

97:

Auto Sequence Fail

Syscon

A0:

Stop request from drive controller was received

A1:

At the mode change command, the mode could
not be changed within specified time and the
drive stopped.

A2:

Retry due to supply error failed and the drive
stopped.

A3:

Disc directory configuration and information file
are illegal and the drive stopped.

A4:

The drive stopped as a DVD-R disc was used.

A5:

Coded data could not be decoded and the drive
stopped.

A6:

At slow R, the destination of reverse search is
illegal and the drive stopped.

A7:

Supply error and stopped.

B0:

SYSCON error was due to supply system.

B1:

SYSCON error was due to VIDEO hung up

B2:

DMX error

B3:

At slow R, data supply time out

B4:

At slow R, wrong Navi Pack sector address

B5:

At slow R, VIDEO hung up

B6:

At slow R, Gttgt end time out

B7:

At FF/FR, data supply time out

B8:

At FF/FR, VIDEO hung up

IFcon

C0:

IFCON ROM destination is wrong

C1:

IFCON UART1 communication port NG

Power system

D0:

The power turned off because of power off re-
quest from drive controller.

D1:

The mode change to Stop mode failed and the
power turned off.

Drvcon

E0:

DRVCON system error

E1:

DRVCON system error

2 MECHA MODE (Mecha mode list)

00:

Power ON Ready

10:

Stop

20:

Trace (data supply mode)

30:

Pause

40:

Drvcon Initialize

50:

Mecha Initialize

6

π:

Spin Up

61:

Adaptation (Tracking Offset)

62:

Adaptation (Jitter/Gain)

63:

TOC/Control Data Read

60:

Etc

70:

Spin Down

80:

Seek

90:

Error Recovery

1 EMG CODE
2 MECHA MODE
3 DISC TYPE (Mecha Mode: 6π)

1 EMG CODE (Emergency code list)

Digital Pass

01:

EEPROM (IC801) Write NG

02:

EEPROM (IC801) Read NG

03:

EEPROM (IC801) Busy Time Out

04:

Emergency History Pointer NG

06:

IFCON SYSCON Communication NG

07:

IFCON V-sync NG

Electrical Adjustment

10:

EEPROM (IC801) Check NG

16:

DSP (IC506) Check NG

Mecha

20:

Home Position Time Out

21:

Sled Driver NG

22:

Sled NG

26:

Tray NG

28:

Door NG

Tilt/Adaptation

30:

Hy Det Level NG

31:

Sled Offset Cancel NG

32:

Focus Gain NG

33:

Tracking Offset NG

34:

Tracking Gain NG

35:

Jitter NG

Focus

40:

Focus Servo Lock NG

41:

Focus Jump NG

Spindle

60:

Miss Chuck

61:

Spindle Lock Time Out

62:

Spindle Reckless

63:

CLV Lock NG

64:

CLV Lock Time Out

65:

CAV Speed NG

66:

Spindle Speed 

×

 1 NG

Seek System

70:

Req Address NG

71:

Req Time Code NG

72:

Req Track No. NG

73:

Seek NG

Data Relation

80:

Address Continuity NG

81:

Address Read NG

82:

TOC Read Time Out

83 – 87:

Physical Information Read Error

88:

Layer No. NG

89:

CD Text Data Read Error

1

2

3

(A)

(B)

6

The self-diagnosis function works to prevent the player from mal-
functioning, a five-digit service number (combination of a letter
and figures) flashes on the screen and front panel display.

1. Each user needs to manage the error. ....................... “C” code

C : 13 : 

ππ

• The disc is dirty.

→

 Clean the disc with a cleaning cloth.

C : 31 : 

ππ

• The disc is not inserted correctly.

→

 Open the disc tray and insert the disc

correctly.

MECHA MODE is shown in 

ππ position.

Code

Description

00

Power ON Ready

10

Stop

20

Trace (data supply mode)

30

Pause

40

Drvcon Initialize

50

Mecha Initialize

6

π

Spin Up

61

Adaptation (Tracking Offset)

62

Adaptation (Jitter/Gain)

63

TOC/Control Data Read

60

Etc

70

Spin Down

80

Seek

90

Error Recovery

3 Disc Type (Mecha Mode: 6π)

(A)

Last result of disc type judgment.

(B)

Initial result of disc type judgment.

Disc type list

FF:

Unknown

00:

No Disc

01:

CD 12 cm

11:

CD 8 cm

02:

Single DVD 12 cm

12:

Single DVD 8 cm

03:

Dual DVD 12 cm

13:

Dual DVD 8 cm

04:

CDR 12 cm

14:

CDR 8 cm

05:

DVDR 12 cm

15:

DVDR 8 cm

Code

Description

92

The number of the times of servo error at
recovery is over regulation.

96

Auto Sequence Time Out

97

Auto Sequence Fail

A0

Stop request from drive controller was received

A1

At the mode change command, the mode could
not be changed within specified time and the
drive stopped.

A2

Retry due to supply error failed and the drive
stopped.

A3

Disc directory configuration and information
file are illegal and the drive stopped.

A4

The drive stopped as a DVD-R disc was used.

A5

Coded data could not be decoded and the drive
stopped.

A6

At slow R, the destination of reverse search is
illegal and the drive stopped.

A7

Information file reading failed and the drive
stopped.

B0

SYSCON error was due to supply system.

B1

SYSCON error was due to VIDEO hung up

B2

DMX error

B3

At slow R, data supply time out

B4

At slow R, wrong Navi Pack sector address

B5

At slow R, VIDEO hung up

B6

At slow R, Gttgt end time out

B7

At FF/FR, data supply time out

B8

At FF/FR, VIDEO hung up

C0

IFCON ROM destination is wrong

C1

IFCON UART1 communication port NG

D0

The power turned off because of power off
request from drive controller.

D1

The mode change to Stop mode failed and the
power turned off.

E0

DRVCON system error

E1

DRVCON system error

2 DISC TYPE

Code

Description

FF

Unknown

00

No Disc

01

CD 12 cm

11

CD 8 cm

02

Single DVD 12 cm

12

Single DVD 8 cm

03

Dual DVD 12 cm

13

Dual DVD 8 cm

04

CDR 12 cm

14

CDR 8 cm

05

DVDR 12 cm

15

DVDR 8 cm

2. Each user needs to contact

with the service section ............................................ “E” code

1 EMG CODE
2 DISC TYPE

1 EMG CODE

Code

Description

01

EEPROM (IC801) Write NG

02

EEPROM (IC801) Read NG

03

EEPROM (IC801) Busy Time Out

04

Emergency History Pointer NG

06

IFCON SYSCON Communication NG

07

IFCON V-sync NG

10

EEPROM (IC801) Check NG

16

DSP (IC506) Check NG

20

Home Position Time Out

21

Sled Driver NG

22

Sled HG

26

Tray NG

28

Door NG

30

Hy Det Level NG

31

Sled Offset Cancel NG

32

Focus Gain NG

33

Tracking Offset NG

34

Tracking Gain NG

35

Jitter NG

40

Focus Servo Lock NG

41

Focus Jump NG

60

Miss Chuck

61

Spindle Lock Time Out

62

Spindle Reckless

63

CLV Lock NG

64

CLV Lock Time Out

65

CAV Speed NG

66

Spindle Speed 

×

 1 NG

70

Req Address NG

71

Req Time Code NG

72

Req Track No. NG

73

Seek NG

80

Address Continuity NG

81

Address Read NG

82

TOC Read Time Out

83 – 87

Physical Information Read Error

88

Layer No. NG

89

CD Text Data Read Error

90

Fail in servo recovery when starting up the disc.

91

Took more than 30 seconds when starting up the
disc.

E :

:

1

2

Mode

E-E

Instrument

Digital voltmeter

+5.2V Check

Test point

CN201 1 pin

Specification

5.2 V ± 0.2 V

+3.3V Check

Test point

CN201 4 pin

Specification

3.3 V ± 0.2 V

EVER+5V Check

Test point

CN201 6 pin

Specification

5.4 V ± 0.2 V

P_CONT Check

Test point

CN201 8 pin

Specification

4 V – 5 V

AU +12V Check

Test point

CN201 9 pin

Specification

12 V      V

AU –12V Check

Test point

CN201 !¡ pin

Specification

–12 V      V

–12V Check

Test point

CN201  !™ pin

Specification

–12 V      V

MTR +12V Check

Test point

CN201 !¢ pin

Specification

12 V      V

1) Confirm that each voltage satisfies the specification.

During diagnostic check, the characters and color bars can
be seen only with the NTSC monitor. Therefore, for diag-
nostic check, use the monitor that supports both NTSC
and PAL modes.
Use the reference disc for PAL for check, and use the ref-
erence disc for NTSC for adjustment.

This section describes procedures and instructions necessary for
adjusting electrical circuits in this set.

1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,

with delay mode

3) Frequency counter (over 8 digits)
4) Digital voltmeter
5) Standard commander (RMT-D107E/D107P)
6) DVD reference disc

HLX-501 (J-6090-071-A) (dual layer) (NTSC)
HLX-503 (J-6090-069-A) (single layer) (NTSC)
HLX-507 (J-6090-078-A)(dual layer) (PAL)
HLX-506 (J-6090-077-A) (single layer) (PAL)

7) Extension cable (J-6090-079-A)

MB-84 (CN601) 

↔

 FL-107 (CN153)

+1.0
–2.0

+2.0
–1.0

+2.0
–1.0

+1.0
–2.0