DOWNLOAD Sony DVP-S335 / DVP-S336 / DVP-S345 / DVP-S535D / DVP-S735D Service Manual ↓ Size: 26.1 MB | Pages: 114 in PDF or view online for FREE

With the set assembled in the front panel, the Test mode does not
become active if any button was pressed by any reason.Under this
condition, the power is not turned on even in the normal status.
(The set is kept in Standby status = Red LED is kept on) Not only
the buttons are inactive, but also a signal from remote commander
is not accepted. To check this condition, with the self check port
(pin 8 of IF CON) kept in “Low” status, supply the AC power, so
that the Test mode is forcibly activated. On the board, short the
lands where SELF is printed. The IF CON checks the self check
port only after the power on reset (only when AC is supplied; not
in Standby status). If any button was pressed, the button name
should be displayed on the FL display tube. Though no button is
pressed this time, display of other than NOTHING implies that
the button was pressed.

1

Red (STANDBY) LED does not light up when AC was sup-
plied. The power (EVER 3.3 V) is not supplied.
X401 is oscillating.

2

Red (STANDBY) LED is kept on though POWER button was
pressed. Any button is kept pressed.
PONCHK (IF CON pin 6) is over 0.1 V.

3

Green LED lights up when POWER button was pressed, but
red LED lights up again after several seconds. PONCHK  (IF
CON pin 6) is abnormal. (Slow rise time from 0.1 V to 1.5 V.
Voltage must be less than 1.5 V)
SYSTEM CONTROL does not operate normally.

EVER 3.3 V may not be supplied normaly. Check that D430 is not
broken.

Mode

E-E

Instrument

Digital voltmeter

EVER +3 V Check

Test point

CN201 pin 1

Specification

3.6 ± 0.2 Vdc

SW +3 V Check

Test point

CN201 pin 2, 3

Specification

3.4 ± 0.2 Vdc

EVER+5 V Check

Test point

CN201 pin 4

Specification

5.3 ± 0.3 Vdc

SW +10 V Check

Test point

CN201 pin 7, 8

Specification

10.5       Vdc

SW –10 V Check

Test point

CN201 pin qa

Specification

–10.0       Vdc

Checking method:
1) Confirm that each voltage satisfies the specification.

During diagnostic check, the characters and color bars can
be seen only with the NTSC monitor. Therefore, for diag-
nostic check, use the monitor that supports both NTSC and
PAL modes.
Use the reference disc for PAL for check, and use the refer-
ence disc for NTSC for adjustment.

This section describes procedures and instructions necessary for
adjusting electrical circuits in this set.

1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,

with delay mode

3) Frequency counter (over 8 digits)
4) Digital voltmeter
5) Standard commander (RMT-D115E/D115P/D116P/D120E/

D120O/D120P)

6) DVD reference disc

HLX-501 (J-6090-071-A) (dual layer) (NTSC)
HLX-503 (J-6090-069-A) (single layer) (NTSC)
HLX-504 (J-6090-088-A) (single layer) (NTSC)
HLX-505 (J-6090-089-A) (dual layer) (NTSC)
HLX-506 (J-6090-077-A) (single layer) (PAL)
HLX-507 (J-6090-078-A)(dual layer) (PAL)

7) SACD reference disc

HLXA-509 (J-6090-090-A)

AUS

: Australian

EA

: Saudi Arabia

+1.0
–1.5

+1.5
–1.0

<Purpose>
This checks component video output B-Y.  If it is incorrect, cor-
rect colors will not be displayed when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

COMPONENT VIDEO OUT (B-Y)
connector (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the B-Y level is 700 ± 70 mVp-p.

<Purpose>
This checks component video output R-Y.  If it is incorrect, cor-
rect colors will not be displayed when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

COMPONENT VIDEO OUT (R-Y)
connector (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the R-Y level is 700 ± 70 mVp-p.

<Purpose>
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

LINE OUT (VIDEO) connector
(75 

Ω 

terminated)

Instrument

Oscilloscope

Adjusting element

RV501

Specification

1.0 ± 0.02 Vp-p

Adjusting method:
1) In the test mode initial menu “6” Video Level Adjustment, set

so that color bars are generated.

2) Adjust the RV501 to attain 1.0 ± 0.02 Vp-p.

<Purpose>
Check S-terminal video output.  If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a S-
terminal cable.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

S VIDEO OUT (S-Y) connector
(75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

1.0 ± 0.1 Vp-p

Checking method:
1) In the test mode initial menu “6” Video Level Adjustment, set

so that color bars are generated.

2) Confirm that the S-Y level is 1.0 ± 0.1 Vp-p.

700 ± 70 mVp-p

700 ± 70 mVp-p

1.0 ± 0.02 Vp-p

1.0 ± 0.1 Vp-p

<Purpose>
This checks component video output Y.  If it is incorrect, correct
brightness will not be attained when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

COMPONENT VIDEO OUT (Y)
connector (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

1.0 ± 0.1 Vp-p

Checking method:
1) Confirm that the Y level is 1.0 ± 0.1 Vp-p.

<Purpose>
This checks RGB output R. If it is incorrect, pictures will not be
displayed correctly in spite of connection to the TV with an EURO
AV connecting cord.

Mode

In test mode,
Push 

[0]

 for Syscon Diagnosis and

push 

[7]

 for Video and push 

[5]

 for

RGB out

Signal

Color bars

Test point

EURO AV 1 (RGB)-TV connector
pin qg (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the R level is 700 ± 70 mVp-p.

<Purpose>
This checks RGB output G.  If it is incorrect, pictures will not be
displayed correctly in spite of connection to the TV with an EURO
AV connecting cord.

Mode

In test mode,
Push 

[0]

 for Syscon Diagnosis and

push 

[7]

 for Video and push 

[5]

 for

RGB out

Signal

Color bars

Test point

EURO AV 1 (RGB)-TV connector
pin qa (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the G level is 700 ± 70 mVp-p.

<Purpose>
This checks RGB output B.  If it is incorrect, pictures will not be
displayed correctly in spite of connection to the TV with an EURO
AV connecting cord.

Mode

In test mode,
Push 

[0]

 for Syscon Diagnosis and

push 

[7]

 for Video and push 

[5]

 for

RGB out

Signal

Color bars

Test point

EURO AV 1 (RGB)-TV connector
pin 7 (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the B level is 700 ± 70 mVp-p.

1.0 ± 0.1 Vp-p

700 ± 70 mVp-p

700 ± 70 mVp-p

700 ± 70 mVp-p