DOWNLOAD Sony DVP-S325 / DVP-S525D / DVP-S725D Service Manual ↓ Size: 55.77 MB | Pages: 127 in PDF or view online for FREE

Mode

E-E

Instrument

Digital voltmeter

+5 V Check

Test point

CN202 pin 5

Specification

5.0 ± 0.2 Vdc

+3.3 V Check

Test point

CN202 pin 7

Specification

3.3 ± 0.2 Vdc

EVER+5 V Check

Test point

CN203 pin 2

Specification

5.0 ± 0.2 Vdc

P_CONT Check

Test point

CN203 pin 1

Specification

4V – 5 Vdc

A +12 V Check

Test point

CN202 pin 1

Specification

9.5       Vdc

–12 V Check

Test point

CN203 pin 5

Specification

–12.0 ± 1.0 Vdc

M +12 V Check

Test point

CN202 pin 2

Specification

12.0 ± 1.0 Vdc

1) Confirm that each voltage satisfies the specification.

+1.5
–0.5

During diagnostic check, the characters and color bars can
be seen only with the NTSC monitor. Therefore, for diag-
nostic check, use the monitor that supports both NTSC and
PAL modes.
Use the reference disc for PAL for check, and use the refer-
ence disc for NTSC for adjustment.

This section describes procedures and instructions necessary for
adjusting electrical circuits in this set.

1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,

with delay mode

3) Frequency counter (over 8 digits)
4) Digital voltmeter
5) Standard commander (RMT-D108O/D108P/D109P/D111O/

D111P)

6) DVD reference disc

HLX-501 (J-6090-071-A) (dual layer) (NTSC)
HLX-503 (J-6090-069-A) (single layer) (NTSC)
HLX-504 (J-6090-088-A) (single layer) (NTSC)
HLX-505 (J-6090-089-A) (dual layer) (NTSC)
HLX-506 (J-6090-077-A) (single layer) (PAL)
HLX-507 (J-6090-078-A)(dual layer) (PAL)

7) SACD reference disc

HLXA-509 (J-6090-090-A)

<Purpose>
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

LINE OUT (VIDEO) connector
(75 

Ω 

terminated)

Instrument

Oscilloscope

Adjusting element

RV401

Specification

1.0 ± 0.02 Vp-p

Adjusting method:
1) In the test mode initial menu “6” Video Level Adjustment, set

so that color bars are generated.

2) Adjust the RV401 to attain 1.0 ± 0.02 Vp-p.

<Purpose>
Check S-terminal video output.  If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a S-
terminal cable.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

S VIDEO OUT (S-Y) connector
(75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

1.0 ± 0.1 Vp-p

Checking method:
1) In the test mode initial menu “6” Video Level Adjustment, set

so that color bars are generated.

2) Confirm that the S-Y level is 1.0 ± 0.1 Vp-p.

<Purpose>
This checks component video output B-Y.  If it is incorrect, cor-
rect colors will not be displayed when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

COMPONENT VIDEO OUT (B-Y)
connector (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the B-Y level is 700 ± 70 mVp-p.

<Purpose>
This checks component video output R-Y.  If it is incorrect, cor-
rect colors will not be displayed when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

COMPONENT VIDEO OUT (R-Y)
connector (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the R-Y level is 700 ± 70 mVp-p.

700 ± 70 mVp-p

1.0 ± 0.02 Vp-p

1.0 ± 0.1 Vp-p

700 ± 70 mVp-p

700 ± 70 mVp-p

700 ± 70 mVp-p

<Purpose>
This checks component video output Y.  If it is incorrect, correct
brightness will not be attained when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

COMPONENT VIDEO OUT (Y)
connector (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

1.0 ± 0.1 Vp-p

Checking method:
1) Confirm that the Y level is 1.0 ± 0.1 Vp-p.

<Purpose>
This checks RGB output R. If it is incorrect, pictures will not be
displayed correctly in spite of connection to the TV with an EURO
AV connecting cord.

Mode

In test mode,
Push 

[0]

 for Syscon Diagnosis and

push 

[7]

 for Video and push 

[5]

 for

RGB out

Signal

Color bars

Test point

EURO AV 1 (RGB)-TV connector
pin !∞ (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the R level is 700 ± 70 mVp-p.

1.0 ± 0.1 Vp-p

<Purpose>
This checks RGB output G.  If it is incorrect, pictures will not be
displayed correctly in spite of connection to the TV with an EURO
AV connecting cord.

Mode

In test mode,
Push 

[0]

 for Syscon Diagnosis and

push 

[7]

 for Video and push 

[5]

 for

RGB out

Signal

Color bars

Test point

EURO AV 1 (RGB)-TV connector
pin !¡ (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the G level is 700 ± 70 mVp-p.

<Purpose>
This checks RGB output B.  If it is incorrect, pictures will not be
displayed correctly in spite of connection to the TV with an EURO
AV connecting cord.

Mode

In test mode,
Push 

[0]

 for Syscon Diagnosis and

push 

[7]

 for Video and push 

[5]

 for

RGB out

Signal

Color bars

Test point

EURO AV 1 (RGB)-TV connector
pin 7 (75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

700 ± 70 mVp-p

Checking method:
1) Confirm that the B level is 700 ± 70 mVp-p.

700 ± 70 mVp-p

<Purpose>
This checks whether the S-C satisfies the NTSC Standard.  If it is
not correct, the colors will be too dark or light.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

S VIDEO OUT (S-C) connector
(75 

Ω

 terminated)

Instrument

Oscilloscope

Specification

286 ± 50 mVp-p (NTSC)
300 ± 100 mVp-p (PAL)

Checking method:
1) In the test mode initial menu “6” Video Level Adjustment, set

so that color bars are generated.

2) Confirm that the S-C burst is 300 ± 100 mVp-p.

300 ± 100 mVp-p