Sony DVP-NS90V / DVP-NS92V Service Manual ▷ View online
2-2
DVP-NS90V/NS92V
2-4. MV-046 BOARD
2-3. REAR PANEL SECTION, AV-097 Board and ER-038 Board
l
l
1
Ten Screws +BV3 (3-CR)
1
Two Screws +BV3 (3-CR)
(DVP-NS92V:
AEP, UK
,RUS)
2
+B3 (3-CR)
4
Rear Panel
3
Power Cord Cable
qa
AV-097 Board
qd
ER-038 Board
(DVP-NS92V:AEP,UK
,RUS)
q;
8
AE-059 Harness
(DVP-NS92V:AEP,UK
,RUS)
(CN902,
11P)
9
FAE-008 Flat Flexible Cable
(DVP-NS92V:AEP,UK
,RUS)
(CN901,
11P)
5
AM-144 Harness (CN302, 7P)
6
FMA-013 Flat Flexible Cable (CN201, 17P)
7
FMA-012 Flat Flexible Cable (CN301, 25P)
qs
Screw +BV3 (3-CR)
3
FMO-013 Flat Flexible Cable (CN101, 24P)
2
PM-126 Harness (CN601, 10P)
6
MV-046 Board
HDMI Out
4
MD-105 Harness
(CN201,
6P)
5
FMS-002 Flat Flexible Cable
(CN202,
5P)
1
Five Screws
+BV3
(3-CR)
b
c
a
d
d
c
b
a
(DVP-NS92V:AEP,UK,RUS)
2-3
DVP-NS90V/NS92V
1
Connector
(PM-126
Harness,
CN201,
10P)
2
Power Cord Cable
4
Power Board
3
Two Screws
+BV3
(3-CR)
2-6. IF-134 Board and CK-153 Board
2-5. SWITCHING REGULATOR
Front Panel
3
IF-134 Board
2
Earth Plate
4
FIM-012 Flat Flaxible Cable
(CN40
4,
19P)
1
Four Screws +BVTP 2.6 (3CR)
1
Two Screws +BVTP 2.6 (3CR)
e
e
6
CK-153 Board
5
IK-053 Harness (CN406, 6P)
q;
Note:
Caution Point on the PWB IF-134
When handling IF-134 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
2-4
DVP-NS90V/NS92V
2-7. LOADING ASSEMBLY
a
a
5
Three Screws
+BV3
(3-CR)
6
Loading Assembly
2
FMO-013 Flat Flexible Cable (CN101, 24P)
1
PM-126 Harness (CN601, 10P)
4
FMS-002 Flat Flexible Cable (CN202, 5P)
3
MD-105 Harness (CN201, 6P)
2-5
DVP-NS90V/NS92V
2-8. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-310CAA/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
After take-out FMO-013 Flexible cable from CN101 of
MV-046 board immediately ground FMO-013 Flexible cable
pattern using short clip. Metal paper clip can be used as
short clip.
MV-046 board immediately ground FMO-013 Flexible cable
pattern using short clip. Metal paper clip can be used as
short clip.
Note:
Solder short land before remove the
FMO-013 Flat Flaxible Cable
from 24 pin BU connector.
FMO-013 Flat Flaxible Cable
from 24 pin BU connector.
Shortland Position
5
FMO-013 Flat Flexible Cable
(CN101,
24P)
4
MD-105 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(KHM-310CAA/C2RP)
2
FFC Holder
Click on the first or last page to see other DVP-NS90V / DVP-NS92V service manuals if exist.