Sony DVP-NS648P Service Manual ▷ View online
– 6 –
3
. CHILD LOCK DISABLED PROCEDURE
When "LOCKED" appears on the front panel display, Child Lock is activated. In order to disable it, either
1) Press O RETURN, ENTER and then ?/1 on the remote when the player is in standby mode.
The player turns on and "UNLOCKED" appears on the front panel display; or
2) Disconnect the player from the wall outlet (AC power source).
Note:
i.
i.
Child Lock is set when you press O RETURN, ENTER, and then ?/1 on the remote during player in standby mode.
ii. The Z buttons on the player or the remote do not work while the Child Lock is set.
4
. BOARD REPLACED PROCEDURE
1) For main board, once EEPROM IC is damaged or not functioning, the mounted PWB must be replaced.
2) After replaced the board inside the player, please see page 6-1 to check the Model Name is correct.
3) For Interface board, please see page 6-4 to check the model.
2) After replaced the board inside the player, please see page 6-1 to check the Model Name is correct.
3) For Interface board, please see page 6-4 to check the model.
– 6E –
2-1
DVP-NS648P
Note: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE
SECTION 2
DISASSEMBLY
2-2. FRONT PANEL ASSEMBLY
Chassis Back
D ust
cover sticker
Two Tapping Screws
Upper case
Tray Cover
Three Tapping Screws
b
c
b
c
Claw
Claw
CN108)
Harness USB-005(
Harness IB-001(CN402)
One Screw
+BVTP 2.6 (3CR)
Bracket
FB-224 Board
One Screw
+BVTP 2.6 (3CR)
One Screw
+BV 3 (3-CR)
Claw
Claw
Note:
Dust cover sticker must be
replaced with a new one
once it is removed. Dust
cover not supplied.
Front Panel Assembly
4
Insert a clip in the hole of a drive
to open a tray.
6
2
7
1
3
5
3
2
6
8
5
1
4
10
11
9
12
2-2
DVP-NS648P
2-3. LOADING ASSEMBLY
6 One S crew
+BV3 (3-CR)
7 Loading Assembly
5 Harness, PM-152
(CN-201, 10P)
1 Flat Flexible Cable,FMO-017 (CN101,24)
3
Flat Flexible Cable, FMS-017(CN202,5P)
2 Harness, MD-125 (CN201, 6P)
4 Harness,PM-152(CN501, 10P)
2-3
DVP-NS648P
2-4. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-313CAA/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge Current
or ElectroStatic Discharge (ESD):
After take-out FMO-017 Flat Flexible Cable from
CN101 of MV-061 board immediately ground FMO-017
CN101 of MV-061 board immediately ground FMO-017
Flat Flexible Cable pattern using short clip. Metal
paper clip can be used as short clip.
5
Flat Flexible Cable (FMO-017)(CN101,24)
4 Harness (MD-125)(CN201, 6P)
1 Four Insulator Screws
6 Two Insulator
6 Two Insulator
3 Optical Device
(KHM- 313CAA/C2RP)
2 FFC Holder
hortland P osition
Note:
Solder shortland before remove the
FMO-017 Flat Flexible Cable
from 24 pin BU connector.
The components identified by
mark or dotted line with mark
mark or dotted line with mark
are critical for safety.
Replace only with part number
specified.
Click on the first or last page to see other DVP-NS648P service manuals if exist.