Sony DVP-NS601HP / DVP-NS700H / DVP-NS700HP / DVP-NS707HP / DVP-NS708H / DVP-NS708HP Service Manual ▷ View online
5-4
DVP-NS601HP/NS700H/NS700HP/NS707HP/NS708H/NS708HP
Pin No.
Pin name
Type
Function
157
XMUTE123
Output, PD, SMT
Motor drive channel 1,2 & 3 mute
158
XMUTE4
Output, PD, SMT
Servo Driver MUTE Signal
159
DDC_SDA
Output, PD, SMT
DDC IIC Data (For HDMI)
160
DVDD18
1.8V power pin for internal digital circuitry
161
DDC_SCL
Output, PD, SMT
DDC IIC Clock (For HDMI)
162
HTPLG
Input, PD, SMT
Hot Plug Detection (For HDMI)
163
AGND33_VPLL
Ground
Ground pin for HDMI TX
164
EXT_RES
Analog Input
External resistor for HDMI TX
165
AVDD33_VPLL
Power
3.3V power pin for HDMI TX
166
AVDD33_TX
Power
3.3V power pin for HDMI TX
167
EXT_CAP
Analog Input
External capacitor for HDMI TX
168
AGND33_TX
Ground
Ground pin for HDMI TX
169
AGND18_TX2
Ground
Ground pin for HDMI TX
170
TXCN
Analog Output
Negative TX Clock
171
TXCP
Analog Output
Positive TX Clock
172
AVDD18_TX1
Power
1.8V power pin for HDMI TX
173
TX0N
Analog Output
Negative TX CH0
174
TX0P
Analog Output
Positive TX CH0
175
AGND18_TX1
Ground
Ground pin for HDMI TX
176
TX1N
Analog Output
Negative TX CH1
177
TX1P
Analog Output
Positive TX CH1
178
AVDD18_TX0
Power
1.8V power pin for HDMI TX
179
TX2N
Analog Output
Negative TX CH2
180
TX2P
Analog Output
Positive TX CH2
181
AGND18_TX0
Ground
Ground pin for HDMI TX
182
R/CR/PR
Analog Output
Red or Cr
183
B/CB/PB
Analog Output
Blue or Cb
184
DACVSSA
Ground
Ground pin for Video DAC circuitry
185
Y/G
Analog Output
Green or Y
186
DACVDDA
Power
3.3V power for Video DAC circuitry
187
CVBS
Analog Output
Analog composite output
188
DACVSSB
Ground
Ground pin for Video DAC circuitry
189
C
Analog Output
Analog chroma output
190
DACVDDB
Power
3.3V power for Video DAC circuitry
191
Y
Analog Output
Analog Y output
192
DACVSSC
Ground
Ground pin for Video DAC circuitry
193
FS
Analog Input
Full Scale Adjustment
194
VREF
Analog Input
Bandgap Ref Voltage
195
DACVDDC
Power
3.3V power for Video DAC circuitry
196
HPD_PON
Output, PD, SMT
Fixed High
197
NC
Not used
198
NC
Not used
199
NC
Not used
200
NC
Not used
201
NC
Not used
202
NC
Not used
203
NC
Not used
204
NC
Not used
205
MV-55: NC
Not used
MV-56: RGBSEL
Output, PD, SMT
RGB/YCbCr select output signal (H:RGB Disable, L:RGB Enable)
206
WIDE
Output
Voltage select output signal for S terminal (H: 16:9, L: 4:3)
207
DVDD33
Power
3.3V power pin for internal digital circuitry
208
NC
Not used
5-5
DVP-NS601HP/NS700H/NS700HP/NS707HP/NS708H/NS708HP
Pin No.
Pin name
Type
Function
209
MV-55: NC
Not used
MV-56: EUROVY
Output, PD, SMT
CVBS/S terminal select output signal (H: CBVS, L: S-terminal)
210
XMAMUTE
Output, PD, SMT
Main Audio Mute signal (H: Unmute, L: Mute)
211
MV-55: NC
Not used
MV-56: DISC/EXT
Output, PD, SMT
DISC/External input select output signal (H: DISC, L: EXTin)
212
DVDD18
Power
1.8V power pin for internal digital circuitry
213
NC
Not used
214
NC
Not used
215
SPDIF
Output
SPDIF output
216
APLLVDD
Power
3.3V Power pin for Clock circuitry
217
APLLCAP
Input
APLL External Capacitance connection
218
APLLVSS
Ground
Ground pin for Clock circuitry
219
ADACVSS2
Ground
Ground pin for Audio DAC circuitry
220
ADACVSS1
Ground
Ground pin for Audio DAC circuitry
221
NC
Not used
222
NC
Not used
223
AR
Analog Output
Audio DAC Right channel output
224
AVCM
Analog Output
Audio DAC Reference Voltage
225
AL
Analog Output
Audio DAC Left Channel Output
226
NC
Not used
227
NC
Not used
228
ADACVDD2
Power
3.3V Power pin for Audio DAC circuitry
229
ADACVDD1
Power
3.3V Power pin for Audio DAC circuitry
230
NC
Not used
231
NC
Not used
232
ADACVSS33
Ground
Ground pin for Audio DAC circuitry
233
ADACVDD33
Power
3.3V Power pin for Audio DAC circuitry
234
SADCVDD18
Power
1.8V Power pin for SACD ADC
235
SADCVSS18
Ground
Ground pin for SACD ADC
236
RFGND18
Ground
Ground pin for internal analog circuitry
237
RFVDD18
Power
1.8V power pin for internal analog circuitry
238
XTALO
Output
27M crystal output
239
XTALI
Input
27M crystal input
240
JITFO
Analog Output
The output terminal of RF jitter meter
241
JITFN
Analog Input
The input terminal of RF jitter meter
242
PLLVSS
Ground
Ground pin for data PLL and related analog circuitry
243
PLLVDD3
Power
3.3V power pin for data PLL and related analog circuitry
244
LPFON
Analog Output
The negative output of loop filter amplifier
245
LPFIP
Analog Input
The positive input terminal of loop filter amplifier
246
LPFIN
Analog Input
The negative input terminal of loop filter amplifier
247
LPFOP
Analog Output
The positive output of loop filter amplifier
248
ADCVDD3
Power
3.3V Power pin for ADC circuitry
249
ADCVSS
Ground
Ground pin for ADC circuitry
250
RFVDD3
Power
3.3V power pin for RF digital circuitry
251
RFRPDC
Analoig Output
RF ripple detect output
252
RFRPAC
Analog Input
RF ripple detect input (through AC-coupling)
253
HRFZC
Analog Input
High frequency RF ripple zero crossing
254
CRTPLP
Analog Output
Defect level filter capacitor connecting
255
RFGND
Ground
Ground pin for RF digital circuitry
256
OSP
Analog Output
RF Offset cancellation capacitor connecting
5-5E
6-1
DVP-NS601HP/NS700H/NS700HP/NS707HP/NS708H/NS708HP
SECTION 6
TEST MODE
6-1.
EXECUTING IOP MEASUREMENT
In order to execute IOP measurement, the following standard
procedures must be followed.
procedures must be followed.
(1)
In standby mode, press [TOP MENU], [CLEAR], [POWER] to
enter Remocon Diagnosis Mode.
enter Remocon Diagnosis Mode.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version information
5. Video Level Adjustment
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version information
5. Video Level Adjustment
Model Name
: xxx xxx xxx
IF-con
: Ver. xxx
Syscon
: Ver. xxx
(2)
Select “2. Drive Manual Operation” by pressing the 2 key on
the remote commander. The screen will appear as below.
the remote commander. The screen will appear as below.
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
0. Return to top Menu
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
0. Return to top Menu
(3)
Select “3. Manual Adjustment” by pressing the 3 key on the
remote commander. The screen will appear as below.
remote commander. The screen will appear as below.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
$4 Change Value
[RETURN] Return to previous menu
[RETURN] Return to previous menu
(4)
Select Iop by pressing 6 key on the remote commander.
(5)
Wait until a hexadecimal number appear.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
$4 Change Value
[RETURN] Return to previous menu
[RETURN] Return to previous menu
(6)
Convert data from hexadecimal to decimal.
(7)
Use the following formula to calculate IOP in mA
IOP (mA)=IOP (decimal) x 0.622678.
IOP (mA)=IOP (decimal) x 0.622678.
(8)
Press [RETURN] to return back to previous menu.
(9)
Press - to return to Top Menu and power OFF the DVD
Player.
Player.
6-2.
EMERGENCY HISTORY CHECK
Information of Emergency History.
(1)
In standby mode, press
[TOP MENU]
,
[CLEAR]
,
[POWER]
to enter Remocon Diagnosis Mode.
(2)
Select “3. Emergency History”.
Emg. History Check
Laser Hours
CD
999h
59min
DVD
999h
59min
1. 01 05 04 04
00 92 46 00
00 00 00 00
00 00 23 45
2. 02 02 01 01
00 A9 4B 00
00 00 00 00
00 00 23 45
[Next] Next Page [Prev] Prev Page
-
-
Return to Top Menu
(3)
Laser Hours
DVD Laser ON time. (Total ON time)
CD Laser ON time. (Total ON time)
DVD Laser ON time. (Total ON time)
CD Laser ON time. (Total ON time)
(4)
Emergency History
The history information from last “1” to “10” can be scrolled
with [NEXT] key or [PREV] key.
The history information from last “1” to “10” can be scrolled
with [NEXT] key or [PREV] key.
(5)
Error code
Example of Error code
1. 01 05 04 04
00 92 46 00
00 00 00 00
00 00 23 45
6-2
DVP-NS601HP/NS700H/NS700HP/NS707HP/NS708H/NS708HP
(6)
Error code list
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mecha move error (5 Changer)
26: Mecha move stack error
30: DC Motor adjustment error
31: DPD offset adjustment error
32: TE Balance adjustment error
33. TE Sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus Layer Jump NG
50. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: read Qdata/ID error
70: Lead In Data Read Fail
71: TOC read time out (CD)
80: Can’t Buffering
81: Unknown media type
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mecha move error (5 Changer)
26: Mecha move stack error
30: DC Motor adjustment error
31: DPD offset adjustment error
32: TE Balance adjustment error
33. TE Sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus Layer Jump NG
50. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: read Qdata/ID error
70: Lead In Data Read Fail
71: TOC read time out (CD)
80: Can’t Buffering
81: Unknown media type
(7)
Error code parameters
Example of Error code
1. 01 05 04 04
00 92 46 00
00 00 00 00
00 00 23 45
This is the detailed contents of error information
(For design used only)
(For design used only)
(8)
Laser hours at error happend.
Example of Error code
1. 01 05 04 04
00 92 46 00
00 00 00 00
00 00 23 45
This is Laser hours when an error happened.
(9)
How to Clear laser hours
Press [DISPLAY], [CLEAR] keys in this order.
Both CD and DVD data are cleared.
Press [DISPLAY], [CLEAR] keys in this order.
Both CD and DVD data are cleared.
Emg. History Check
Laser Hours
CD
0h
0min
DVD
0h
0min
1. 01 05 04 04
00 92 46 00
00 00 00 00
00 00 23 45
2. 02 02 01 01
00 A9 4B 00
00 00 00 00
00 00 23 45
[Next] Next Page [Prev] Prev Page
-
-
Return to Top Menu
(10) How to Clearing Emergency code
Press [TOPMENU], [CLEAR] keys in this order.
All emergency code are cleared.
All emergency code are cleared.
Emg. History Check
Laser Hours
CD
999h
59min
DVD
999h
59min
1. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
2. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
[Next] Next Page [Prev] Prev Page
-
Return to Top Menu
(11) Press - key, return to TOP MENU.
6-3.
INITIALIZING SETUP DATA
How to initializing setup data.
(1)
In standby mode, press [TOP MENU], [CLEAR], [POWER] to
enter Remocon Diagnosis Mode.
enter Remocon Diagnosis Mode.
(2)
Select “3. Emergency History”.
Emg. History Check
Laser Hours
CD
999h
59min
DVD
999h
59min
1. 01 05 04 04
00 92 46 00
00 00 00 00
00 00 23 45
2. 02 02 01 01
00 A9 4B 00
00 00 00 00
00 00 23 45
[Next] Next Page [Prev] Prev Page
-
-
Return to Top Menu
(3)
Initializing setup data
Press [MENU], [CLEAR] keys in this order.
The data have been initialized when “Initialize setup data...”
mesage is displayed.
Press [MENU], [CLEAR] keys in this order.
The data have been initialized when “Initialize setup data...”
mesage is displayed.
Emg. History Check
Laser Hours
CD
999h
59min
DVD
999h
59min
Initialize setup data ...
[Next] Next Page [Prev] Prev Page
-
-
Return to Top Menu
r
r
Click on the first or last page to see other DVP-NS601HP / DVP-NS700H / DVP-NS700HP / DVP-NS707HP / DVP-NS708H / DVP-NS708HP service manuals if exist.