Sony DVP-NS38 / DVP-NS39 / DVP-NS47P / DVP-NS57P / DVP-NS64P / DVP-NS67P Service Manual ▷ View online
2-1
DVP-NS28/NS38/NS39/NS47P/NS57P/NS64P/NS67P
Note: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE
SECTION 2
DISASSEMBLY
2-2. FRONT PANEL ASSEMBLY
4
Two Tapping Screws
6
Upper case
3
Tray Cover
5
Three Tapping Screws
2
1
Chassis Back
4
Claw
1
Claw
2
Claw
3
Claw
5
Front Panel Assembly
2-2
DVP-NS28/NS38/NS39/NS47P/NS57P/NS64P/NS67P
2-3. LOADING ASSEMBLY
a
a
4
Three Screws
+BV3
(3-CR)
5
Loading Assembly
1
FMO-008 Flat Flexible Cable (CN101, 24P)
3
FMS-013 Flat Flexible Cable (CN202, 5P)
2
MD-111 Harness (CN201, 6P)
2-3
DVP-NS28/NS38/NS39/NS47P/NS57P/NS64P/NS67P
2-4. OPTICAL PICK-UP
(DEVICE, OPTICAL KHM-313CAA/C2RP)
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge Current or
ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge Current or
ElectroStatic Discharge (ESD):
After take-out FMO-008 Flat Flexible Cable from CN101 of
MV-52/53/54 board immediately ground FMO-008 Flat
Flexible Cable pattern using short clip. Metal paper clip can be
used as short clip.
MV-52/53/54 board immediately ground FMO-008 Flat
Flexible Cable pattern using short clip. Metal paper clip can be
used as short clip.
5
FMO-008 Flat Flexible Cable (CN101, 24P)
4
MD-111 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(KHM-313CAA/C2RP)
2
FFC Holder
Shortland Position
Note:
Solder shortland before remove the
FMO-008 Flat Flexible Cable from
24 pin BU connector.
FMO-008 Flat Flexible Cable from
24 pin BU connector.
2-4
DVP-NS28/NS38/NS39/NS47P/NS57P/NS64P/NS67P
2-5. REAR PANEL, MV-52/53/54 BOARD and IF-150 BOARD
a).
(DVP-NS28/NS38/NS39 ONLY)
o
2
o
5
FMS-013 Flat Flexible Cable
(CN202,
5P)
6
FMO-008 Flat Flexible Cable
(CN101,
24P)
8
MV-53 Board
4
MD-111 Harness
(CN201,
6P)
9
PM-136 Harness
(CN501,
10P)
7
Three Screws
+BV3
(3-CR)
Three Screws
+BV3 (3-CR)
+BV3 (3-CR)
3
Rear Panel
1
One Tapping Screw
qa
IF-150 Board
a
o
q;
Two Screws
+BV3
(3-CR)
c
qs
Board to Board
Connector
c
a
Note:
Caution Point on the PWB IF-150
Caution Point on the PWB IF-150
When handling IF-150 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
Click on the first or last page to see other DVP-NS38 / DVP-NS39 / DVP-NS47P / DVP-NS57P / DVP-NS64P / DVP-NS67P service manuals if exist.