Sony DVP-NC625 / DVP-NC665P / HT-6600DP Service Manual ▷ View online
— 5 —
DVP-NC625/NC665P
1.
NOTE ON REMOVING THE UPPER
CASE
CASE
1)
Remove the four tapping screws and three screws. (See Fig. 1)
2)
Open the sides of case. (See Fig. 1)
3)
Remove the upper case in the direction of the arrow A.
2.
DISC REMOVAL PROCEDURE
1)
Insert a flat-head (-) screwdriver into a hole at the bottom, and
rotate the cam gear in the direction of the arrow A. (See Fig.2)
rotate the cam gear in the direction of the arrow A. (See Fig.2)
Two tapping screws
Two tapping screws
Three screws (B3)
A
3.
NOTE ON REMOVING THE TABLE
ASS’Y
ASS’Y
1)
Remove the two screws. (See Fig. 3)
Cam gear
Table
Hole
A
Screw
(M2.6
(M2.6
8)
Screw
(M2.6 8)
(M2.6 8)
✕
✕
2)
Remove the two Plates (guide) in the direction of the arrows
A
A
and B.
3)
Remove the Table ass’y in the direction of the arrow C.
4)
Remove the Flexible flat cable (See Fig. 4).
Plate (guide)
Plate (guide)
Table ass'y
Flexible flat cable
(FMS-18: CN002)
(FMS-18: CN002)
C
B
A
Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
SERVICE NOTE
— 6 —
DVP-NC625/NC665P
4.
NOTE ON MOUNTING THE GEARS
1)
Mount the gear (chuck). (See Fig. 5)
2)
Rotate the gear (chuck) in the direction of the arrow. (down
position) (See Fig. 5)
position) (See Fig. 5)
3)
Connect the boss of the gear (swing) with the groove of the
rotary encoder and mount the gear (swing). (See Fig. 6)
rotary encoder and mount the gear (swing). (See Fig. 6)
4)
Align triangle mark of the chassis with the groove of the gear
(swing).
(swing).
Gear (chuck)
Gear (swing)
Gear (swing)
Boss
Groove
Align triangle mark of the chassis
with the groove of the gear (swing).
with the groove of the gear (swing).
5)
Mount the gear (idler) while aligning the engagement of the
gear (swing) and the gear (chuck). (See Fig. 7)
gear (swing) and the gear (chuck). (See Fig. 7)
Gear
(idler)
(idler)
Gear (idler)
Gear (chuck)
Gear (swing)
Engagement the gear (swing) and the gear (chuck).
Fig. 5.
Fig. 6.
Fig. 7.
— 7 —
DVP-NC625/NC665P
5.
HOW TO SERVICE THE MB-108
BOARD
BOARD
1)
Remove the upper case from the set. (Refer to section 2-1)
2)
Remove the MB-108 board. (Refer to section 2-4)
3)
Set the MB-108 board in the stand (with CK-121 board) as
shown in Fig. 9.
shown in Fig. 9.
FFC 26P J-6090-117-A,
FFC 9P J-6090-118-A,
FFC 25P J-6090-122-A,
FFC 11P J-6090-120-A
FFC 9P J-6090-118-A,
FFC 25P J-6090-122-A,
FFC 11P J-6090-120-A
Harness 6P (J-6090-126-A)
CK-120 board
(J-6090-127-A)
Stand
(CK-121 board)
(J-6090-132-A)
Five flexible flat cables
Jig
4)
Set the CK-120 board in the place where the MB-108 board is
removed, as shown in Fig. 10.
removed, as shown in Fig. 10.
Connector (CN101)
Stand
(with CK-121 board)
MB-108 board
Two screws (B3)
Connector
(CN109)
Board to board
connector (CN111)
CK-120
board
Four screws (B3)
Flexible flat cable
(FMO-6: CN103)
Flexible flat cable
(FMM-42: CN101)
Flexible flat cable
(FMC-15: CN107)
Fig. 8.
Fig. 9.
Fig. 10.
— 8 —
DVP-NC625/NC665P
5)
Set the four flexible flat cables as shown in Fig. 11.
6)
Set the flexible flat cable and the harness as shown in Fig. 12.
Connector
(CN304)
Connector
(CN203)
Harness
(6P: CN102)
Flexible flat cable
(FFC 25P: CN601)
Connector
(CN102)
MB-108
Connector
(CN104)
Connector
(CN301)
Flexible flat cable
(FFC 9P: CN204)
Flexible flat cable
(FFC 26P: CN203)
7)
Set is finished.
Fig. 11.
Fig. 12.
Click on the first or last page to see other DVP-NC625 / DVP-NC665P / HT-6600DP service manuals if exist.