Sony DVP-M20P Service Manual ▷ View online
2-1
DVP-M20P
Note: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE, COVER TRAY
SECTION 2
DISASSEMBLY
2-2. FRONT PANEL ASSEMBLY and PL-040 BOARD
2
Tapping Screw
5
Cover Assy Tray
1
Three Screws
(Screw,
Tapping)
+BV3
(3-CR)
4
3
Chassis Back
6
Front Panel Assembly
5
Claw
3
Claw
4
Claw
2
Claw
7
One Screw
+BVT2.6
(3CR)
1
Harness PI-064 (CN402, 5P)
8
PL-040 Board
2-2
DVP-M20P
2-3. REAR PANEL
1
Four Screws
+BV3
(3-CR)
3
Rear panel
2
Power Cord
2-4. LOADING ASSEMBLY
4
Three Screws
+BV3
(3-CR)
5
Loading Assembly
1
FMO-007 Flat Flexible Cable (CN101, 24P)
3
FMS-006 Flat Flexible Cable (CN202, 5P)
2
MD-110 Harness (CN201, 6P)
6
FIM-010 Flat Flexible Cable (CN106, 17P)
2-3
DVP-M20P
2-5. OPTICAL DEVICE
(DEVICE, OPTICAL KHM-310CAA/C2RP)
5
FMO-007 Flat Flexible Cable
(CN101,
24P)
4
MD-110 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(DEVICE,
OPTICAL
KHM-310CAA/C2RP)
2
FFC Holder
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
After take-out FMO-007 Flat Flexible cable from CN101
of MV-045 board immediately ground FMO-007 Flexible
cable pattern using short clip. Metal paper clip can be used
as short clip.
of MV-045 board immediately ground FMO-007 Flexible
cable pattern using short clip. Metal paper clip can be used
as short clip.
Note:
Solder short land before
remove the harness from
24 pin BU connector.
remove the harness from
24 pin BU connector.
Short Land Position
2-4
DVP-M20P
1
+BV3 (3-CR)
0
FIM-010 Flat Flexible Cable (CN106, 5P)
8
MV-045 Board
6
PM-122 Harness (CN501, 10P)
3
MD-110 Harness (CN201, 6P)
5
FMO-007 Flat Flexible Cable (CN101, 24P)
4
FMS-006 Flat Flexible Cable (CN202, 6P)
7
Five Screws
+BV3
(3-CR)
9
Three Screws
+BV3
(3-CR)
2
Hook
qa
IF-132 Board
qs
Harness PI-064 (CN402, 5P)
qd
FIM-010 Flat Flexible Cable (CN401, 17P)
a
a
2-6. SWITCHING REGULATOR
2-7. MV-045 and IF132 BOARDS
1
Two Screws
+BV3
(3-CR)
2
Hook
3
Connector
(PM-122
Harness,
CN501,
10P)
4
Power Board
a
a
a
Click on the first or last page to see other DVP-M20P service manuals if exist.