Sony DVP-LS500 Service Manual ▷ View online
5-1
SECTION 5
IC PIN FUNCTION DESCRIPTION
D
VP-LS500
Pin No.
Pin name
I/O
Function
39
SCL
O
I2C clock output
40
TRM+
-
Not used
41
EUROVY
O
Euro VIDEO signal output
42
EXT/DSEL
O
Line input/output select signal output
43
MD0
I
Input of mode select 0 (fixed at “ H”)
44
MD1
I
Input of mode select 1 (fixed at “ L”)
45
MD2
I
Input of mode select 2 (fixed at “ L”)
46
DREQ0
I
AV DEC DMA –REQ0 input
47
DACK0
O
AV DEC DMA –ACK0 output
48
XDRVMUTE
O
Drive mute signal output
49
DREQ1
I
AV DEC DMA –REQ1 input
50
DACK1
O
AV DEC DMA –ACK1 output
51
XIFCS
O
IF CON Chip select signal output
52
VSS
-
Ground
53
X1 (OUT)
O
Clock output (16.5 MHz)
54
X2 (IN)
I
Clock input (16.5 MHz)
55
VCC
-
Power supply (+3.3 V)
56
CKSW1/TSW1
I
Chuck Sensor input
57
OCSW1/TSW2
I
Tray Sensor input
58
CS0X
O
External ROM chip select signal output
59
CS1X
O
Extranal RAM chip select signal output
60
CS2X
O
AV DEC Chip select signal output
61
CS3X
O
AV DEC Chip select signal output
62
CS4X
O
ARP Chip select signal output
63
CS5X
O
SDSP Chip select signal output
64
VCCI
-
Power supply (+1.8 V)
65
CS6X
-
Not used
66
CS7X
-
Not used
67
XWAIT
I
Wait signal input
68
BGRNTX
I
Test terminal (fixed at “H”)
69
BRQ
-
Not used
70
XRD
O
Read enable signal output
71
XWRH
O
High order-byte write enable signal output
72
XWRL
O
Lower order-byte write enable signal output
Pin No.
Pin name
I/O
Function
1-5
HA17 to HA21
O
Address bus A17 to A21
6
HA22
-
Not used
7
WP
O
I2C EEPROM write protect output
8
XSACS
-
Not used
9
AVCC
-
Power supply (+3.3 V)
10
AVRH
-
Reference power supply (+3.3 V)
11
AVSS
-
Ground
12
AN0
I
Set of mode 0
13
AN1
I
Set of mode 1
14
AN2
I
Set of mode 2
15
AN3
-
Not used
16
INT0
I
AV DEC Interrupt input
17
INT1
I
ARP Interrupt input
18
INT2
I
SDSP Interrupt input
19
INT3
-
Not used
20
INT4
I
IF CON Interrupt input
21
INT5
-
Not used
22
INT6
-
Not used
23
INT7
-
Not used
24
VCC
-
Power supply (+3.3 V)
25
SI0
I
Serial bus 0 (data input)
26
SO0
O
Serial bus 0 (data output)
27
SC0
O
Serial bus 0 (clock output)
28
SI1
-
Not used
29
SO1
O
Serial bus 1 (data output)
30
SC1
O
Serial bus 1 (clock output)
31
SI2
I
Serial bus 2 (data input)
32
SO2
O
Serial bus 2 (data output)
33
DSENS
-
Not used
34
VSS
-
Ground
35
XRST
O
System reset signal output
36
XARPRST
O
WIDE Select signal output
37
RGBSEL
O
VIDEO Select signal output
38
SDA
I/O
I2C data input/output
5-1. SYSTEM CONTROL PIN FUNCTION (MB-108 BOARD IC104)
5-2 E
Pin No.
Pin name
I/O
Function
73
NMIX
I
Non Maskable Interrupt input (fixed at "H")
74
VCCI
-
Power supply (+1.8 V)
75
VSS
-
Ground
76
XFRRST
I
IF CON Reset signal input
77
CPUCK
O
CPU clock signal output
78
OCSW2
-
Not used
79
XDACS
O
DAC (2ch) chip select signal output
80
TRM-
-
Not used
81
48/44.1K
O
PLL FS control signal output
82
WIDE
O
Laser diode mute signal output
83
MA_MUTE
O
Audio mute signal output
84
SRAMWE
O
SRAM write enable signal output
85 to 92
HD0 to HD7
I/O
Data bus D0 to D7 (16 bit only)
93 to 100
HD8 to HD15
I/O
Data bus D8 to D15 (16 bit) , D0 to D7 (8 bit)
101
VSS
-
Ground
102 to 109
HA0 to HA7
O
Address bus A00 to A07
110
VCC
-
Power supply (+3.3 V)
111 to 118
HA8 to HA15
O
Address bus A08 to A15
119
VSS
-
Ground
120
HA16
O
Address bus A16
6-1
6-3.
SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press
checked from the remote commander.
On the Test Mode Menu screen, press
[0]
key on the remote com-
mander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
_
0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
1. All items continuous check
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judg-
ment through a visual check to the result, the following screen is
displayed for the key entry.
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judg-
ment through a visual check to the result, the following screen is
displayed for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = xxxx
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
>
key to go to the next item,
or
.
key to repeat the same check again. To quit the diagnosis
and return to the Check Menu screen, press
x
or
[ENTER]
key.
If an error occurred, the diagnosis is suspended and the error code
is displayed as shown below.
is displayed as shown below.
### Syscon Diagnosis ###
3-2. EEPROM Check
Error 03: EEPROM Write/Reed N
Address
: 00000001
Write Data : 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press
x
key to quit the diagnosis, or
.
key to repeat the same
item where an error occurred, or
>
key to continue the check
from the item next to faulty item.
6-1.
GENERAL DESCRIPTION
The Test Mode allows you to make diagnosis and adjustment eas-
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
6-2.
STARTING TEST MODE
Press the
[TOP MENU]
,
[CLEAR]
,
[I/ ]
keys on the remote com-
mander in this order with the power of main unit in OFF status,
and the Test Mode starts, then “DIAG STARTING START” will
be displayed on the fluorescent display tube and the menu shown
below will be displayed on the TV screen. At the bottom of menu
screen, the model name and revision number are displayed. Last
Off at the lower right of screen indicates the information code
concerning the last power off.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the
and the Test Mode starts, then “DIAG STARTING START” will
be displayed on the fluorescent display tube and the menu shown
below will be displayed on the TV screen. At the bottom of menu
screen, the model name and revision number are displayed. Last
Off at the lower right of screen indicates the information code
concerning the last power off.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the
[I/ ]
key.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency Hisory
5. Version Information
6. Video Level Adjustment
Exit: POWER Key
_
Model
:DPX-17xxxx
Revision :x.xxx
Last Off: xx
Power Off Information Code List
00 :
Primary Power Off
01 :
Power Off Request from SYSTEM CONTROL
02 :
Power Off by Emergency Power Off Command from SYS-
TEM CONTROL
(if information is sent from SYSTEM CONTROL)
TEM CONTROL
(if information is sent from SYSTEM CONTROL)
03 :
IF CON Judged that SYSTEM CONTROL is Faulty
04 :
Power Off from Diagnosis Mode of IF CON
05 :
Forced Power Off by the User
06 :
Power Off by Power Supply Voltage Monitor
SECTION 6
TEST MODE
DVP-LS500
1
1
6-2
* In "All item continuous check", pressing stop or enter will not
quit the diagnosis.
Selecting 2 and subsequent items calls the submenu screen of
each item.
When “–––––––” is displayed in the submenu, it means that the
test is not supported in the model.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
each item.
When “–––––––” is displayed in the submenu, it means that the
test is not supported in the model.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
_
0. Quit
Quit the submenu and return to the main menu.
1. All submenu items continuous check
All submenu items continuous check.
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another au-
tomatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “General Description of
Checking Method” and “Check Items List”.
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another au-
tomatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “General Description of
Checking Method” and “Check Items List”.
General Description of Checking Method
2. Version
(2-2) Revision
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file of ROM
(IC106 or 107) is displayed with four digits.
Error: Not detected.
The revision number defined in the source file of ROM
(IC106 or 107) is displayed with four digits.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
8-bit data are added up to the ROM (IC106 or 107) address
0x000F0000 to 0x002EFFFF, and the result is displayed
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
Error: Not detected.
8-bit data are added up to the ROM (IC106 or 107) address
0x000F0000 to 0x002EFFFF, and the result is displayed
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code read from the EEPROM is displayed with
2-digit hexadecimal number.
Error: Not detected.
The model code read from the EEPROM is displayed with
2-digit hexadecimal number.
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is dis-
played.
Error: Not detected.
The region code determined from the model code is dis-
played.
(2-6) M't check
Mount resistance is checked.
Error 22: The region code does not accord.
Check wether the region code that is deduced from model
resistance and destination resistance accords with the re-
gion code that is deduced from region resistance value.
Error 22: The region code does not accord.
Check wether the region code that is deduced from model
resistance and destination resistance accords with the re-
gion code that is deduced from region resistance value.
3. Peripheral
(3-2) EEPROM Check
Data write
→ read, and accord check
Error 03: EEPROM write/read discord.
0x9249, 0x2942 and 0x4294 are written to the address 0x00
to 0xFF of the EEPROM and then read for checking. Be-
fore writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
0x9249, 0x2942 and 0x4294 are written to the address 0x00
to 0xFF of the EEPROM and then read for checking. Be-
fore writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
(3-3) –––––––
Check no support.
(3-4) –––––––
Check no support.
(3-5) –––––––
Check no support.
(3-6) VENC Check
Data write
→ read, and accord check
Error 52: Write and read data discord.
Accessing to the SYSCON may be defective.
Accessing to the SYSCON may be defective.
(3-7) –––––––
Check no support.
(3-8) EX RAM Check
Test Data write
→ read, and accord check
Error 02: The external RAM used in the system control is
checked.
checked.
4. Servo
(4-2) Servo DSP Check
Data write
→ read, and accord check
Error 12: Read data discord
0x9249, 0x2942 and 0x4294 are written to the RAM ad-
dress 0x602 of the Servo DSP and then read for checking.
0x9249, 0x2942 and 0x4294 are written to the RAM ad-
dress 0x602 of the Servo DSP and then read for checking.
(4-3) –––––––
Check no support.
(4-4) RF Amp (SSI) W/R Check
Date write
→ read and accord check
Error 13: RF Amp resister write, and read data discord
Implement 8-bit shift operation of the 0x01 to the read-
able/writable register of the RF Amp. If once write data do
not accord with read data, it is NG.
Implement 8-bit shift operation of the 0x01 to the read-
able/writable register of the RF Amp. If once write data do
not accord with read data, it is NG.
Click on the first or last page to see other DVP-LS500 service manuals if exist.