Sony DVP-K800D Service Manual ▷ View online
— 9 —
4-6.
Note on Mounting FG-43 Board
1)
Align two bosses. (See Fig.11)
2)
Fix the board securely with screws (PTPWH 2
×
5). (The sensor
will not function normally if the board floats up.)
Fig. 11
4-7.
Note on Mounting TK-47 Board
1)
Align two bosses. (See Fig.12)
2)
Align four tabs. (See Fig.12)
3)
Fix the board securely with 3 screws (BV 3
×
10). (The sensor
will not function normally if the board floats up.)
Fig.12
Screw
(PTPWH2
(PTPWH2
×
5)
FG-43 board
Two bosses
Three screws
(BV3
(BV3
× 10
)
TK-47 board
Boss
Two claws
Boss
Two claws
5.
EMERGENCY CODE INDICATION
5-1.
Users are expected to take care of the
followings by themselves – – – – “C” code
“C : 13 : XX
Clean the disc”
“C : 31 : XX
Remove and insert the disc again”
XX
00
10
20
30
40
50
61
62
63
60
70
80
90
PON ready
Stop
Trace
Pause
Drvcon Unit
Mecha Unit
Spin Up
Tracking offset
Jitter/Gain
TOC/Control Data Read
Others
Spin Down
Seek
Error Recovery
5-2.
Consult Sony Service – – – “E” code,
E : YY : ZZ
Refer to the item “5-8. Appendix” for details.
YY
01
02
03
04
06
07
10
16
21
30
31
32
33
34
35
40
41
42
60
61
62
63
EEPROM reading: NG (Check Sum has abnormality)
EEPROM writing: NG (Check Sum has abnormality)
EEPROM BUSY is displayed continuously exceeding
the specified time.
the specified time.
The pointer that shows the newest Emg History has
abnormality.
abnormality.
Communication between the HI microprocessor and
the SYS microprocessor is interrupted for a specified
time.
the SYS microprocessor is interrupted for a specified
time.
HI microprocessor cannot detect V-sync.
EEPROM CHECK NG
DSP CHECK NG
Sled driver has abnormal voltage.
Hy Det Level adjustment has abnormality.
Sled Offset Cancel adjustment has abnormality.
Focus Gain adjustment is faulty.
Tracking Offset adjustment is faulty.
Tracking Gain adjustment is faulty.
JITTER NG (only during the automatic adjustment)
Focus Servo does not lock in.
Focus Jump failed.
DSP Error Code (not used)
Mis-chucking when disc is inserted.
When disc started rotation, it did not reach the target
speed within 3 seconds.
speed within 3 seconds.
Spindle runs away/does not stop.
Lock Check (in the service mode only)
— 10 —
YY
64
65
66
70
71
72
73
80
81
82
83
84
85
86
87
88
89
90
96
97
A0
A1
A2
A3
A4
A5
A6
A7
B0
B1
B2
B3
B4
B5
B6
B7
B8
C0
C1
D0
D1
E0
E1
CLV servo does not lock in within the specified time.
FG servo does not reach the target speed within the
specified time.
specified time.
Spindle is not rotating at x1 speed. (RF Edge)
System control requests address that does not exist.
System control requests time code that is not used.
System control requests track No. that is not used.
The lock-in operation is not completed within the
specified number of times.
specified number of times.
Continuity of address has abnormality. (DVD)
Cannot read address even retry is executed. (CD)
TOC read is not completed within the specified period
of time.
of time.
Physical Information Read Error ( CTRL DATA ECC
ERR)
ERR)
Physical Information Read Error ( CTRL DATA
INSA ERR)
INSA ERR)
Physical Information Read Error ( CTRL DATA
FULL ERR)
FULL ERR)
Physical Information Read Error ( CTRL DATA RUN
OVER)
OVER)
Physical Information Read Error ( CTRL DATA Time
Out)
Out)
Layer No has abnormality.
CD Text Data Read Error
Servo recovery has failed when starting a disc.
Auto Sequence Time Out
Auto Sequence has exceeded the specified times.
Stop request from drive microprocessor
Did not return to the mode for a specified time.
Feed error. Retry is impossible.
GetInfo error. Stop
An attempt is made to playback a DVD-R Disc
Failed to execute Decrypt
SlowR. Target address of searching is illegal.
Feed error. Stop
Due to feeder.
Due to video hang-up
Error in DMX
Waiting for data from SlowR
Navi Pack sector address is different during SlowR
mode
mode
Video hang-up during SlowR mode
Time out while waiting for ending of SlowR Gttgt
Waiting for data during FF/FR
Waiting for video data during FF/FR
The installed HI microprocessor ROM does not match
the destination.
the destination.
HI microprocessor UART1 communication port has
abnormality.
abnormality.
EMG code is not present upon power-off request from
drive microprocessor
drive microprocessor
Cannot return t stop mode. Power Off
Drive microprocessor - system error (STATUS ERR)
Drive microprocessor - system error (MECHAM
MODE ERR)
MODE ERR)
ZZ
FF
00
01
02
12
03
13
04
14
05
15
UNKONWN
NO DISC
CD 12 cm
CD 8 cm
SINGLE DVD 12 cm
SINGLE DVD 8 cm
DUAL 12 cm
CDR 12 cm
CDR 8 cm
DVDR 12 cm
DVDR 8 cm
1-1
DVP-K800D
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
1-2
Click on the first or last page to see other DVP-K800D service manuals if exist.