DOWNLOAD Sony DVP-F5 / DVP-FX1 Service Manual ↓ Size: 23.56 MB | Pages: 122 in PDF or view online for FREE

6-15

Command

: 22

Operation

: The following operation is repeated.

LCD all segments turn on (5 seconds) All
segments turn on (5 seconds) 

→ Model name

display (2 seconds) 

→ ROM version display (2

seconds) 

→ ROM creation date display (2

seconds).

LCD display : As described above.

mode
Command

: 23

Operation

: The forced output that is specified by the test

mode item No. 6, No. 7, No. 10 to No. 7 and No.
30 to No. 32 are initialized.

LCD display : “23 

− ini”

* The TFT PANEL is set to the default state from

the NTSC/PAL setting.

* POWER_SAVE TFT inverter high output
* Forced ON output to TFT LCD INVPCON
* Forced ON output to TFT LCD power supply

TFTPCON

* LCD backlight check forced ON output
* CHGCNT forced OFF output, LBCHG forced

ON output

Command

: 24

Operation

: The 3.3 V input voltage is displayed on LCD.

* Valid range during POWER ON

2.02 V (272h)        PON_CHK        2.42 V
(2FDh)

* Valid range during STAND-BY

PON_CHK        0.1 V (01Fh)

LCD display : “24 

− XXX”.  XXX is the input voltage.

* Reference value : This value is around 2C6.

Command

: 25

Operation

: The DC_OUT voltage is displayed on LCD.

* Valid voltage when the DC OUT JACK is

connected.
1.28 V (18Dh)        DC OUT MNT

LCD display : “25 

− XXX”.  XXX is the input voltage.

* Reference value : This value is around 1A8 to

198.

Command

: 26

Operation

: The BATT voltage is displayed on LCD.

* Valid voltage when operated on battery.

1.43 V (1BDh)        BATTMNT < 2.03 V (276h)

LCD display : “26 

− XXX”.  XXX is the input voltage.

* Reference value : This value is around 275 to

1BD.

Command

: 27

Operation

: The DC_IN voltage is displayed on LCD.

* Valid voltage when operated on DC.

1.96 V (261h)        VCCMNT    <   2.65 V
(335h)

LCD display : “27 

− XXX”.  XXX is the input voltage.

* Reference value : This value is around 261 to

334.

<

=

<

=

<

=

<

=

<

=

<

=

Command

: 28

Operation

: Even when the LINE IN/OUT is switched by

the VIDEO switch for the TFT LCD monitor
EVR adjustment, the DVDPCON is maintained
in the ON state and the V_IOCNT output is
switched so that the LINE OUT picture or the
LINE IN picture is output to the TFT LCD.
When the machine enters this mode, the state
that is specified by the test mode is initialized.
* XPAL and EVR setting

During LINE IN mode

XPAL : NTSC setting
EVR : NTSC setting

During LINE OUT mode

XPAL : NTSC setting
EVR : NTSC setting

LCD display : “28-tFt” + NTSC segment display

Command

: 29

Operation

: Even when the LINE IN/OUT is switched by

the VIDEO switch for the TFT LCD monitor
EVR adjustment, the DVDPCON is maintained
in the ON state and the V_IOCNT output is
switched so that the LINE OUT picture or the
LINE IN picture is output to the TFT LCD.
When the machine enters this mode, the state
that is specified by the test mode is initialized.
* XPAL and EVR setting

During LINE IN mode

XPAL : PAL setting
EVR : PAL setting

During LINE OUT mode (The XPAL is set to
the NTSC setting in order to display the
SYScon diagnosis display on the TFT LCD.)

XPAL : NTSC setting
EVR : PAL setting

LCD display : “29-tFt” + NTSC segment display

Command

: 30

Operation

: The CHGCNT is forced to ON and the LBCHG

is forced to OFF.  (The charging processing is
interrupted.)
When charging is in progress in the STAND

−

BY mode, the charging processing is interrupted.
When charging is in progress in the POWER ON
mode, the machine enters the forced STAND-
BY mode.
When 10 minutes have elapsed after the forced
charge is set to ON, the forced charging is
cancelled.
When charging is started by any commands other
than this command, the machine follows their
outputs after charging is started once.

LCD display : “30 

− on”

6-16

Command

: 31

Operation

: The CHGCNT is forced to OFF and the LBCHG

is forced to ON.
When charging is in progress in the STAND-
BY mode, the charging processing is interrupted.
When charging is in progress in the POWER ON
mode, the machine enters the forced STAND-
BY mode.
When charging is started by any commands other
than this command, the machine follows their
outputs after charging is started once.

LCD display : “31 

− OFF”

charging the low voltage battery)
Command

: 32

Operation

: The CHGCNT is forced to ON and the LBCHG

is forced to ON.  (The charging processing is
interrupted.)
When charging is in progress in the STAND-
BY mode, the charging processing is interrupted.
When charging is in progress in the POWER ON
mode, the machine enters the forced STAND-
BY mode.
When 10 minutes have elapsed after the forced
charge is set to ON, the forced charging is
cancelled.
When charging is started by any commands other
than this command, the machine follows their
outputs after charging is started once.

LCD display : “32 

− on”

Command

: 34

Operation

: When charging is in progress in the POWER ON

mode, the machine enters the forced STAND-
BY mode.
The charging processing is interrupted and the
charging is re-started.

LCD display : “34 

− St”

Command

: 36

Operation

: The VCCMNT voltage that is inputted by the

charging sequence is displayed.
* Valid voltage of VCCMNT

1.96 V (261h)        VCCMNT   <   2.65 V
(335h)

LCD display : “36 

− XXX”.  XXX is the input voltage.

* Reference value : This value is around 261 to

334.

CHGMNT = ON)
Command

: 37

Operation

: The CHGMNT voltage that is inputted by the

charging sequence is displayed. (Voltage when
CHGMNT = ON)
* Valid voltage of BATTMTN

5.0 V (156h)        BATTMTN   <   1.90 V
(24Dh)

LCD display : “37 

− XXX”.  XXX is the input voltage.

* Reference value : This value is around 156 to

24C.

CHGMNT = OFF)
Command

: 38

Operation

: The CHGMNT voltage that is inputted by the

charging sequence is displayed. (Voltage when
CHGMNT = OFF)
* Valid voltage of BATTMTN

BATTMTN   <   1.90 V (24Dh)

LCD display : “38 

− XXX”.  XXX is the input voltage.

* Reference value:  This value is around 0 to 24C.

Command

: 40

Operation

: Charging status display

LCD display : “40 

− XXX”.  XXX is the charging status data.

* Contents of the charging status display

00h : State waiting for starting of charging.
01h : Continuous charging is in progress.
02h : Full charged judgment processing is in

progress.

03h : Supplementary charging of 1 hour is in

progress.

04h : Normal charging is complete.
05h : The 1 hour timer has ended.
06h : The 12 hour timer has ended.
07h : Charging the low voltage battery is in

progress during the continuous charging.

10h : Charging is terminated due to the

charging condition error.

11h : Charging is terminated due to the

abnormal voltage during continuous
charging.

12h : Charging is terminated due to the

abnormal voltage when full charged
condition is detected.

13h : Charging is terminated due to the

abnormal voltage during the
supplementary charging.  (Or normal
end.)

14h : Charging is terminated due to abnormal

voltage of 8.6 V or more of battery
voltage when fully charged.

15h : Charging is terminated due to abnormal

voltage of 5.0 V or less battery voltage
when fully charged.

<

=

<

=

6-17

Command

: 41

LCD display : “41 

− m n”

m : BATT switch = “1” (Already connected state)

or “0” (Not connected yet state) display.

m : BATTYPE = “1” (Lithium-ion battery) or “0”

(Other batteries than the lithium-ion battery)
display.

6-18E