Sony DVP-F41MS Service Manual ▷ View online
6-2
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
_
Submenu
Selecting 2 and subsequent items calls the submenu screen of
each item.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
each item.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
0. Quit
Quit the submenu and return to the main menu.
1. All (All submenu items continuous check.)
This menu checks 2 and subsequent items successively. At the
item where visual check is required for judgment or an error
occurred, the checking is suspended and the message is output for
key entry.
Normally, all items are checked successively one after another
automatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “General Description of
Checking Method” and “Check Items List”.
item where visual check is required for judgment or an error
occurred, the checking is suspended and the message is output for
key entry.
Normally, all items are checked successively one after another
automatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “General Description of
Checking Method” and “Check Items List”.
General Description of Checking Method
2. Version
(2-2)
Revision
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file of ROM
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file of ROM
(IC107) is displayed with four digits.
(2-3)
ROM Check Sum
Check sum is calculated.
Error: Not detected.
8-bit data are added up to the ROM (IC107) address
Check sum is calculated.
Error: Not detected.
8-bit data are added up to the ROM (IC107) address
0x000F0000 to 0x002EFFFF, and the result is displayed
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
(2-4)
Model Type
Model code is displayed.
Error: Not detected.
The model code read from the EEPROM is displayed
Model code is displayed.
Error: Not detected.
The model code read from the EEPROM is displayed
with 2-digit hexadecimal number.
Model Type
DVP-F21
UC
5
0
MX
5
2
CE1
5
3
CE2
5
4
GA
5
7
AU
5
a
CN
5
c
(2-5)
Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is
Region code is displayed.
Error: Not detected.
The region code determined from the model code is
displayed.
3. Peripheral
(3-2)
EEPROM Check
Data write
Data write
→ read, and accord check
Error 03: EEPROM write/read discord
0x9249, 0x2942 and 0x4294 are written to the address
0x00 to 0xFF of the EEPROM and then read for
checking. Before writing, the data are saved, then after
checking, they are written to restore the contents of
EEPROM.
0x9249, 0x2942 and 0x4294 are written to the address
0x00 to 0xFF of the EEPROM and then read for
checking. Before writing, the data are saved, then after
checking, they are written to restore the contents of
EEPROM.
4. Servo
(4-2)
Servo DSP Check
Data write
Data write
→ read, and accord check
Error 12: Read data discord
0x9249, 0x2942 and 0x4294 are written to the RAM
address 0x602 of the Servo DSP and then read for
checking.
Also, OPT type “1 LASER” or “2 LASER” is displayed.
0x9249, 0x2942 and 0x4294 are written to the RAM
address 0x602 of the Servo DSP and then read for
checking.
Also, OPT type “1 LASER” or “2 LASER” is displayed.
(4-3)
DSP Driver Test
Test signal data
Test signal data
→ DSP Driver
Error: Not detected.
Caution: Do not perform this checking with the mechanical deck
connected.
The maximum voltage is applied to the Servo Driver IC
(IC401). If the mechanical deck is connected, it will be
destroyed immediately. Following the output message,
disconnect the mechanical deck, then enter the
specified 4- or 5-digit value from the commander, and
press the
The maximum voltage is applied to the Servo Driver IC
(IC401). If the mechanical deck is connected, it will be
destroyed immediately. Following the output message,
disconnect the mechanical deck, then enter the
specified 4- or 5-digit value from the commander, and
press the
[ENTER]
key. The test is conducted only if
the entered value accords. To exit the test, check the
output level, then press
output level, then press
[NEXT]
key.
This check is not conducted, but skipped in “All” menu
item.
item.
6-3
### Syscon Diagnosis ###
5-4. ARP to RAM Address Bus
Error 10: ARP - RAM Address B
Address
: 0000A55A
Write Data : 00000000
Read Data
: 00080000
Press NEXT Key to Continue
Press PREV Key to Repeat
_
5. Supply
(5-2)
ARP Register Check
Data write
Data write
→ read, and accord check
Error 08: ARP register write, and read data discord
Data 0x00 to 0xFF is written sequentially to the ARP
TMAX register (address 0xC6) and then read for
checking.
Data 0x00 to 0xFF is written sequentially to the ARP
TMAX register (address 0xC6) and then read for
checking.
(5-3)
ARP to RAM Data Bus
Data write
Data write
→ read, and accord check
Error 09: ARP
← → RAM data bus error
Data 0x0001 to 0x8000 where one bit each is set to 1 are
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of
written data, the line could be disconnected or shorted.
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of
written data, the line could be disconnected or shorted.
(5-4)
ARP to RAM Address Bus
Data write
Data write
→ other address read discord check
Error 10: ARP
→ RAM address bus error
Caution: Address and data display in case of an error is
different from the display of other diagnosis
(described later).
(described later).
Before starting the test, all addresses of RAM (IC303) are
cleared to 0x0000. First, 0xA55A is written to the address
0x00000, and the address data are read and checked from
addresses 0x00001 to 0x80000 while shifting 1 bit each.
Next, the data at that address is cleared, and it is written
to the address 0x00001, and read and checked in the same
manner. This check is repeated up to the address 0x80000
while shifting the address data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were
already cleared to 0. In this check, the error display
pattern is different from that of other diagnosis; read data,
written address, and read address are displayed in this
order. However, the message uses same template, and
accordingly exchange Address and Data when reading.
The following display, for example, shows the data
0xA55A was read from address 0x00080000 though it
was written to the address 0x00000000. This implies that
these addresses are in the form of shadow. Also, if the
read data is not 0xA55A, another error will be present.
cleared to 0x0000. First, 0xA55A is written to the address
0x00000, and the address data are read and checked from
addresses 0x00001 to 0x80000 while shifting 1 bit each.
Next, the data at that address is cleared, and it is written
to the address 0x00001, and read and checked in the same
manner. This check is repeated up to the address 0x80000
while shifting the address data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were
already cleared to 0. In this check, the error display
pattern is different from that of other diagnosis; read data,
written address, and read address are displayed in this
order. However, the message uses same template, and
accordingly exchange Address and Data when reading.
The following display, for example, shows the data
0xA55A was read from address 0x00080000 though it
was written to the address 0x00000000. This implies that
these addresses are in the form of shadow. Also, if the
read data is not 0xA55A, another error will be present.
(5-5)
ARP RAM Check
Data write
Data write
→ read, and accord check
Error 11: ARP RAM read data discord
The program code data stored in ROM are copied to all
areas of RAM (IC303) connected to the ARP (IC302)
through the bus, then they are read and checked if they
accord. If the detail check was selected initially, the data
are written to all areas and read, then the same test is
conducted once again with the data where all bits are
inverted between 1 and 0. If discord is detected, faulty
address, written data, and read data are displayed
following the error code 11, and the test is suspended.
The program code data stored in ROM are copied to all
areas of RAM (IC303) connected to the ARP (IC302)
through the bus, then they are read and checked if they
accord. If the detail check was selected initially, the data
are written to all areas and read, then the same test is
conducted once again with the data where all bits are
inverted between 1 and 0. If discord is detected, faulty
address, written data, and read data are displayed
following the error code 11, and the test is suspended.
6. AV Decoder
(6-2)
1930 RAM
Data write
Data write
→ read, and accord check
Error 13: AVD RAM read data discord
The program code data stored in ROM (IC107) are copied
to all areas of RAM (IC504, IC505) connected to the
AVD (IC503) through the bus, then they are read and
checked if they accord. Further, the same test is
conducted once again with the data where all bits are
inverted between 1 and 0. If discord is detected, faulty
address, written data, and read data are displayed
following the error code 13, and the test is suspended.
During the test, OSD display becomes blank as the OSD
area is also checked.
The program code data stored in ROM (IC107) are copied
to all areas of RAM (IC504, IC505) connected to the
AVD (IC503) through the bus, then they are read and
checked if they accord. Further, the same test is
conducted once again with the data where all bits are
inverted between 1 and 0. If discord is detected, faulty
address, written data, and read data are displayed
following the error code 13, and the test is suspended.
During the test, OSD display becomes blank as the OSD
area is also checked.
(6-3)
1930 SP
ROM
ROM
→ AVD RAM → Video OUT
Error: Not detected.
The data including sub picture streams in ROM (IC107)
are transferred to the RAM (IC504, IC505) in AVD
(IC503), and output as video signals from the AVD
(IC503).
Though OSD display becomes blank, the output of video
signals continues until the key is pressed.
They are output from all video terminals (Composite, Y/
C, Component) except EURO AV terminal.
The data including sub picture streams in ROM (IC107)
are transferred to the RAM (IC504, IC505) in AVD
(IC503), and output as video signals from the AVD
(IC503).
Though OSD display becomes blank, the output of video
signals continues until the key is pressed.
They are output from all video terminals (Composite, Y/
C, Component) except EURO AV terminal.
6-4
7. Video
(7-2)
Color Bar
AVD color bar command write
AVD color bar command write
→ Video OUT
Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/
C, Component) except EURO AV terminal.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/
C, Component) except EURO AV terminal.
(7-3)
Composite Out
EURO-AV Composite video output check
AVD color bar command write
EURO-AV Composite video output check
AVD color bar command write
→ Video (EURO-AV
Composite) OUT
Error: Not detected.
With the Component of video output turned off, the color
bar signals are output from the EURO-AV terminal.
Error: Not detected.
With the Component of video output turned off, the color
bar signals are output from the EURO-AV terminal.
(7-4)
Y/C Out
EURO-AV Y/C video output check
AVD color bar command write
EURO-AV Y/C video output check
AVD color bar command write
→ Video (EURO-AV Y/C)
OUT
Error: Not detected.
With the Y/C of video output turned on, the color bar
signals are output from the EURO-AV terminal.
Error: Not detected.
With the Y/C of video output turned on, the color bar
signals are output from the EURO-AV terminal.
8. Audio
(8-2)
ARP
→ 1930
Error 14: ARP
→ 1932 video NG
15: ARP
→ 1932 audio NG
(8-3)
Test Tone
A pink noise signal is output from the AVD (IC503)
through optical coaxial digital terminal and analog audio
terminal.
Error: Not detected.
After turning on all outputs, each time the
A pink noise signal is output from the AVD (IC503)
through optical coaxial digital terminal and analog audio
terminal.
Error: Not detected.
After turning on all outputs, each time the
[NEXT]
key is
pressed, the output channel is switched for individual
channel checking.
Left + Right
channel checking.
Left + Right
→ Left → Right are checked in this order.
9. Memory Stick
(9-0)
Quit
(9-1)
All
Checks all of items (9-2) to (9-8).
Checks all of items (9-2) to (9-8).
(9-2)
Download check
Checks whether the software for DSP can be downloaded
Checks whether the software for DSP can be downloaded
from flash ROM IC107 through the host port interface of
IC1104.
IC1104.
(9-3) MS_RAM check
Checks whether the internal shared RAM of DSP IC1104
is not damaged.
is not damaged.
(9-4) CXK2K/MS check
Checks whether the data from EEPROM IC1102
(CXK2000) can be read normally and that a memory stick
can be read normally.
(CXK2000) can be read normally and that a memory stick
can be read normally.
(9-5)
DA_output
Checks whether sine-wave audio data of 1 kHz from DSP
Checks whether sine-wave audio data of 1 kHz from DSP
IC1104 is normally output through DAC IC802. Sine-
wave audio data of 1 kHz is output from the AUDIO
OUT terminal.
wave audio data of 1 kHz is output from the AUDIO
OUT terminal.
(9-6)
PLL-output
Checks whether the multiplied frequency (132 MHz) of
crystal oscillator X1103 (12 MHz) is normally output
from pin 15 (CLKOUT) of DSP IC1104.
Checks whether the multiplied frequency (132 MHz) of
crystal oscillator X1103 (12 MHz) is normally output
from pin 15 (CLKOUT) of DSP IC1104.
(9-8)
DSP_REV display
Displays the hardware revision number of DSP IC1104.
Displays the hardware revision number of DSP IC1104.
(9-9)
CODE_REV display
Displays the microcode software version number of DSP
Displays the microcode software version number of DSP
IC1104.
Note: An error occurs if check items from (9-3) to (9-8)
are executed before Download check in item (9-2)
is passed.
is passed.
Check Items List
2)
2)
Version
(2-2)
Revision
(2-3)
ROM Check Sum
(2-4)
Model Type
(2-5)
Region
3)
Peripheral
(3-2)
Gate Array Check
(3-3)
EEPROM Check
4)
Servo
(4-2)
Servo DSP Check
(4-3)
DSP Driver Test
5)
Supply
(5-2)
ARP Register Check
(5-3)
ARP to RAM Data Bus
(5-4)
ARP to RAM Address Bus
(5-5)
ARP RAM Check
6)
AV Decoder
(6-2)
1930 RAM
(6-3)
1930 SP
7)
Video
(7-2)
Color Bar
(7-3)
Composite Out
(7-4)
Y/C Out
8)
Audio
(8-2)
ARP
→ 1930
(8-3)
Test Tone
9)
Memory Stick
(9-2)
Download check
(9-3)
MS_RAM check
(9-4)
CXK2K/MS check
6-5
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
4. LCD
Exit: RETURN
Error Codes List
00: Error not detected
01: RAM write/read data discord
02: Gate array NG
03
01: RAM write/read data discord
02: Gate array NG
03
: EEPROM NG
04
: Flash memory clear error
05
: Flash memory write error
06
: Flash memory read data discord
07
: 2725 read data discord
08
: ARP register read data discord
09
: ARP ← → RAM data bus error
10
: ARP ← → RAM address bus error
11
: ARP RAM read data discord
12
: Servo DSP NG
13
: 1932 SDRAM NG
14
: ARP → 1932 video NG
15
: ARP → 1932 audio NG
16
: 1910 UCODE download NG
17
: System call error (function not supported)
18
: System call error (parameter error)
19
: System call error (illegal ID number)
20
: System call error (time out)
21
: NAND Flash faulty blocks exceed 10
90
: Error occurred
91
: User verification NG
92
: Diagnosis cancelled
6-4. DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press
[1]
key on the remote
commander, and the drive auto adjustment menu will be dis-
played.
played.
Normally,
[0]
is selected to adjust DVD (single layer), CD, DVD
(dual layer), and LCD (SACD) in this order. But, individual items
can be adjusted for the case where adjustment is suspended due to
an error. In this mode, the adjustment can be made easily through
the operation following the message displayed on the screen.
Which disc is currently adjusted is displayed on the fluorescent
display tube.
The disc used for adjustment must be the one specified for
adjustment.
can be adjusted for the case where adjustment is suspended due to
an error. In this mode, the adjustment can be made easily through
the operation following the message displayed on the screen.
Which disc is currently adjusted is displayed on the fluorescent
display tube.
The disc used for adjustment must be the one specified for
adjustment.
0. ALL
You will be asked if EEPROM data are initialized or not, and for
this prompt, select
this prompt, select
[0]
and press the
[ENTER]
key. First, the
servo setting data in EEPROM, Emergency History and Hour
Meter are cleared to initialize. Then, 1. DVD-SL disc, 2. CD disc,
3. DVD-DL disc, and 4. LCD disc (SACD disc) are adjusted in
this order. Each time one disc was adjusted, it is ejected, and
therefore exchange the disc following the message. Though the
message to confirm whether the discs is to be adjusted is not
displayed except for LCD disk (SACD disk), you can exit the
adjustment by pressing the
Meter are cleared to initialize. Then, 1. DVD-SL disc, 2. CD disc,
3. DVD-DL disc, and 4. LCD disc (SACD disc) are adjusted in
this order. Each time one disc was adjusted, it is ejected, and
therefore exchange the disc following the message. Though the
message to confirm whether the discs is to be adjusted is not
displayed except for LCD disk (SACD disk), you can exit the
adjustment by pressing the
[STOP]
button. In adjusting each
disc, the mirror time is measured to check the disk type. In the
auto adjustment, whether the disc type is correct is not checked
unlike conventional models, and accordingly, take care not to
insert a different type of disc.
auto adjustment, whether the disc type is correct is not checked
unlike conventional models, and accordingly, take care not to
insert a different type of disc.
1. DVD-SL (single layer)
Select
[1]
, insert DVD single layer disc, and press
[ENTER]
key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
adjusted values will be written to the EEPROM.
DVD Single Layer Disc Adjustment Steps
1.
SLED TILT Reset
2.
Disc Check Memory SL
3.
Set Disc Type SL
4.
Spdl Start
5.
Wait 1 sec
6.
LD ON
7.
Focus Error Check
8.
Focus ON 0
9.
Auto Track Offset Adjust L0
10. Trv Level Check
11. Tracking ON
12. Wait 100 msec
13. CLVA ON
14. Wait 500 msec
15. Sled ON
16. Auto Loop Filter Offset Adjust
17. Auto Focus Gain Adjust L0
18. Auto Focus Balance Adjust L0
19. EQ Boost Adjust
20. Auto Loop Filter Offset Adjust
21. RF Level Measure
22. Jitter Disp ON
23. Jitter Memory
24. Jitter Disp OFF
25. Eep Copy Loop Filter Offset
26. All Servo Stop
11. Tracking ON
12. Wait 100 msec
13. CLVA ON
14. Wait 500 msec
15. Sled ON
16. Auto Loop Filter Offset Adjust
17. Auto Focus Gain Adjust L0
18. Auto Focus Balance Adjust L0
19. EQ Boost Adjust
20. Auto Loop Filter Offset Adjust
21. RF Level Measure
22. Jitter Disp ON
23. Jitter Memory
24. Jitter Disp OFF
25. Eep Copy Loop Filter Offset
26. All Servo Stop
Click on the first or last page to see other DVP-F41MS service manuals if exist.