DOWNLOAD Sony DVP-F21 Service Manual ↓ Size: 5.02 MB | Pages: 88 in PDF or view online for FREE

Note:

During diagnostic check, the characters and color bars
can be seen only with the NTSC monitor. Therefore, for
diagnostic check, use the monitor that supports both
NTSC and PAL modes.
Use the reference disc for PAL for check, and use the
reference disc for NTSC for adjustment.

This section describes procedures and instructions necessary for
adjusting electrical circuits in this set.

1)

Color monitor TV

2)

Single or dual trace oscilloscope, band width over 100 MHz,
with delay mode

3)

Frequency counter (over 8 digits)

4)

Digital voltmeter

5)

Standard commander (RMT-D126A/D126E/D126P)

6)

DVD reference disc
HLX-501 (J-6090-071-A) (dual layer) (NTSC)
HLX-503 (J-6090-069-A) (single layer) (NTSC)
HLX-504 (J-6090-088-A) (single layer) (NTSC)
HLX-505 (J-6090-089-A) (dual layer) (NTSC)
HLX-506 (J-6090-077-A) (single layer) (PAL)
HLX-507 (J-6090-078-A) (dual layer) (PAL)

7)

SACD reference disc
HLXA-509 (J-6090-090-A)

8)

Extension Cable (J-6090-107-A)

Mode

E-E

Instrument

Digital voltmeter

1

 EVER +3.3 V Check

Test point

JL708

Specification

3.3 

±

 0.1 Vdc

2

 SW +3.3 V Check

Test point

JL710

Specification

3.3 

±

 0.2 Vdc

3

 +5 V Check

Test point

JL709

Specification

5.0 

±

 0.3 Vdc

4

 SW +11 V Check

Test point

JL706, JL707

Specification

10.5 

±

 0.5 Vdc

5

 EVER +5 V Check

Test point

JL711

Specification

5.0 

±

 0.2 Vdc

6

 SW –11 V Check

Test point

JL705

Specification

–11.0 

±

 1.0 Vdc

7

 +1.8 V Check

Test point

JL713

Specification

1.8 

±

 0.1 Vdc

1)

Confirm that each voltage satisfies the specification.

A

This checks whether the S-C satisfies the NTSC/PAL Standard. If
it is not correct, the colors will be too dark or light.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

S VIDEO OUT (S-C) connector
(75 

Ω

 terminated)

Instrument

Oscilloscope

Specification

A = 286 

±

 30 mVp-p (NTSC)

A = 300 

±

 100 mVp-p (PAL)

1)

In the test mode initial menu “6” Video Level Adjustment,
set so that color bars are generated.

2)

Confirm that the S-C burst is “A” meets the specification.

This adjustment is made to satisfy the NTSC/PAL standard, and if
not adjusted correctly, the brightness will be too large or small.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

LINE OUT (VIDEO) connector
(75 

Ω

 terminated)

Instrument

Oscilloscope

Adjusting element

RV501

Specification

1.0

+0.04

 Vp-p

–0.02

1)

In the test mode initial menu “6” Video Level Adjustment,
set so that color bars are generated.

2)

Adjust the level to 1.0

+0.04

 Vp-p by RV501.

–0.02

Check S-terminal video output. If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with an S-
terminal cable.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

S VIDEO OUT (S-Y) connector
(75 

Ω

 terminated)

Instrument

Oscilloscope

Specification

1.0 

±

 0.05 Vp-p

1)

In the test mode initial menu “6” Video Level Adjustment,
set so that color bars are generated.

2)

Confirm that the S-Y level is 1.0 

±

 0.05 Vp-p.

1.0      Vp-p

+0.04
–0.02

1.0

±

0.05Vp-p

RV501

V-ADJ

NOTE:

• -XX and -X mean standardized parts, so they may

have some difference from the original one.

• Items marked “*” are not stocked since they are

seldom required for routine service. Some delay
should be anticipated when ordering these items.

• The mechanical parts with no reference number in

the exploded views are not supplied.

• Hardware (# mark) list and accessories and pack-

ing materials are given in the last of the electrical
parts list.

The components identified by mark
! or dotted line with mark ! are criti-
cal for safety.
Replace only with part number speci-
fied.

Les composants identifiés par une
marque 

!  sont critiques pour la

sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

Ref.No.

Part No.

Description

Remarks

1

3-070-471-01

CASE, LOWER (US, CND) (Silver)

1

3-070-471-11

CASE, LOWER (US, CND) (Black)

1

3-070-471-51

CASE, LOWER (EXCEPT US, CND)

2

3-070-472-01

COVER, TERMINAL (Silver)

2

3-070-472-11

COVER, TERMINAL (Black)

3

X-3951-902-2

CASE ASSY (S), UPPER (Silver)

3

X-3951-928-2

CASE ASSY (S), UPPER (Black)

4

A-6062-617-A

MD ASSY

5

3-970-608-51

SUMITITE (B3), +BV

6

3-053-847-11

INSULATOR

Ref.No.

Part No.

Description

Remarks

! 7

8-820-144-14

OPTICAL PICK-UP KHM240AAA/J1RP2

8

3-067-344-01

INSULATOR SCREW

9

1-823-249-11

CABLE, FLEXIBLE FLAT (FOB-2)

10

1-823-248-11

CABLE, FLEXIBLE FLAT (FOB-1)

11

3-070-486-01

FOOT (Silver)

11

3-070-486-11

FOOT (Black)

12

3-070-491-01

COVER, GATE

13

1-476-887-11

REMOTE COMMANDER (RMT-D137A)

(US, CND, MX)

13

1-476-887-31

REMOTE COMMANDER

(EXCEPT US, CND, MX) (RMT-D137P)

14

3-709-572-0

BATTERY COVER

Ref.No.

Part No.

Description

Remarks

51

X-3951-919-1

GATE ASSY

52

3-070-596-01

SPRING,COMPRESSION

53

X-3951-920-1

LEVER ASSY

54

3-703-358-05

PIN,PARALLEL (DIA.2X16)

55

3-070-587-01

SPRING, EXTENSION

56

X-3951-918-1

ARM ASSY,CHUCKING

57

3-070-583-01

ROLLER (HP)

58

3-727-176-01

WASHER, STOPPER

59

3-070-592-01

YOKE HOLDER

60

3-070-591-01

YOKE

61

3-070-590-01

CHUCK PULLEY

62

3-070-595-01

SPRING, EXTENSION

63

3-070-579-01

HOLDER, BU

64

4-933-134-41

SCREW (+PTPWH 2.6X5)

65

3-070-585-01

SPRING (SLIDER)

Ref.No.

Part No.

Description

Remarks

66

3-070-577-01

RACK (L)

67

1-823-246-11

CABLE, FLEXIBLE FLAT (FDM-22)

68

X-3951-914-1

MOTOR (C) ASSY

69

3-070-576-01

BRACKET (C), MOTOR

70

3-070-573-01

WHEEL (C), WORM

71

3-070-574-01

GEAR (C1)

72

3-070-575-01

GEAR (C2)

73

X-3951-911-1

BASE (C) ASSY

74

1-823-250-11

CABLE, FLEXIBLE FLAT (FDD-12)