Sony DVP-CX985V Service Manual ▷ View online
3
DVP-CX985V
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15
µ
F
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher than
• Unleaded solder melts at a temperature about 40 ˚C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if the
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges oc-
cur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges oc-
cur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
4
DVP-CX985V
This Player Can Play the
Following Discs
Following Discs
“DVD VIDEO” and “DVD-RW” are
trademarks.
trademarks.
Region code
Your player has a region code printed on the
back of the unit and will only play DVD
VIDEOs (playback only) labeled with
identical region codes. This system is used to
protect copyrights.
back of the unit and will only play DVD
VIDEOs (playback only) labeled with
identical region codes. This system is used to
protect copyrights.
DVD VIDEOs labeled
will also play on
this player.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD VIDEO, no region
code indication may be labeled even though
playing the DVD VIDEO is prohibited by
area restrictions.
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD VIDEO, no region
code indication may be labeled even though
playing the DVD VIDEO is prohibited by
area restrictions.
Format of discs
DVD VIDEO
DVD-RW
Super Audio CD
VIDEO CD
Music CD
ALL
X
Region code
Example of discs that the player
cannot play
cannot play
The player cannot play the following discs:
•
All CD-ROMs (including PHOTO CDs)/
CD-Rs/CD-RWs other than those recorded
in the following formats:
−music CD format
−video CD format
−MP3 format that conforms to ISO9660*
CD-Rs/CD-RWs other than those recorded
in the following formats:
−music CD format
−video CD format
−MP3 format that conforms to ISO9660*
Level 1/Level 2, or its extended format,
Joliet
Joliet
•
Data part of CD-Extras
•
DVD-ROMs
•
DVD Audios
* A logical format of files and folders on CD-
ROMs defined by ISO (International Standards
Organization).
Organization).
Also, the player cannot play the following
discs:
discs:
•
A DVD VIDEO with a different region
code.
code.
•
A disc recorded in a color system other than
NTSC, such as PAL or SECAM (this player
conforms to the NTSC color system).
NTSC, such as PAL or SECAM (this player
conforms to the NTSC color system).
•
A disc that has a non-standard shape (e.g.,
card, heart).
card, heart).
•
A disc with paper or stickers on it.
•
A disc that has the adhesive of cellophane
tape or a sticker still left on it.
tape or a sticker still left on it.
Notes
• Note about DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs, or CD-Rs/CD-RWs.
Some DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs, or CD-Rs/CD-RWs cannot be played
on this player due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software. Also, images in DVD-RWs
with CPRM* protection may not be played if they
contain a copy protection signal. “Copyright
lock” appears on the screen. For more
information, see the operating instructions for the
recording device.
Note that discs created in the Packet Write format
cannot be played.
* CPRM (Content Protection for Recordable
Some DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs, or CD-Rs/CD-RWs cannot be played
on this player due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software. Also, images in DVD-RWs
with CPRM* protection may not be played if they
contain a copy protection signal. “Copyright
lock” appears on the screen. For more
information, see the operating instructions for the
recording device.
Note that discs created in the Packet Write format
cannot be played.
* CPRM (Content Protection for Recordable
Media) is a coding technology that protects
copyright for images.
copyright for images.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Note on playback operations of
DVDs and VIDEO CDs
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Copyrights
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
5
DVP-CX985V
SELF DIAGNOSIS FUNCTION
....................................
2
1.
SERVICING NOTES
...............................................
6
2.
GENERAL
................................................................... 10
3.
DISASSEMBLY
3-1. Disassembly Flow ........................................................... 11
3-2. Case ................................................................................. 12
3-3. MB Board ........................................................................ 12
3-4. AV Board ......................................................................... 13
3-5. Bracket (L)/(R) ................................................................ 13
3-6. Front Panel Section ......................................................... 14
3-7. Cover (PT)/(CDM) .......................................................... 14
3-8. DVBU26 Assy ................................................................. 15
3-9. Power Block .................................................................... 15
3-10. Table (400) Assy ............................................................. 16
3-11. Door Block, Base (Door) Assy ....................................... 16
3-12. DC Motor (Door) (M603) ............................................... 17
3-13. Holder (Table Sensor 400) .............................................. 17
3-14. D. SENS OUT Board, D. SENS IN Board ..................... 18
3-15. Pop-up (400) Assy ........................................................... 18
3-16. Door SW Board ............................................................... 19
3-17. Lock SW Board, Loading SW Board ............................. 20
3-18. CD/DVD Mechanism Deck Block
3-2. Case ................................................................................. 12
3-3. MB Board ........................................................................ 12
3-4. AV Board ......................................................................... 13
3-5. Bracket (L)/(R) ................................................................ 13
3-6. Front Panel Section ......................................................... 14
3-7. Cover (PT)/(CDM) .......................................................... 14
3-8. DVBU26 Assy ................................................................. 15
3-9. Power Block .................................................................... 15
3-10. Table (400) Assy ............................................................. 16
3-11. Door Block, Base (Door) Assy ....................................... 16
3-12. DC Motor (Door) (M603) ............................................... 17
3-13. Holder (Table Sensor 400) .............................................. 17
3-14. D. SENS OUT Board, D. SENS IN Board ..................... 18
3-15. Pop-up (400) Assy ........................................................... 18
3-16. Door SW Board ............................................................... 19
3-17. Lock SW Board, Loading SW Board ............................. 20
3-18. CD/DVD Mechanism Deck Block
(CDM62-DVBU26) ........................................................ 21
3-19. Motor (400) Assy (Loading) (M602)/(Table) (M601),
Loading Motor Board ..................................................... 21
3-20. Optical Pick-up (KHM-290AAA) .................................. 22
4.
TEST MODE
.............................................................. 23
5.
MECHANICAL ADJUSTMENTS
....................... 45
6.
ELECTRICAL ADJUSTMENTS
......................... 46
7.
DIAGRAMS
7-1. Block Diagram – RF Section – ...................................... 50
7-2. Block Diagram – SERVO/CHANGER Section – ......... 51
7-3. Block Diagram – AUDIO Section – .............................. 52
7-4. Block Diagram – VIDEO Section – .............................. 53
7-5. Block Diagram
7-2. Block Diagram – SERVO/CHANGER Section – ......... 51
7-3. Block Diagram – AUDIO Section – .............................. 52
7-4. Block Diagram – VIDEO Section – .............................. 53
7-5. Block Diagram
– PANEL/POWER SUPPLY Section – .......................... 54
7-6. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 55
7-7. Printed Wiring Board
– MB Board (Component Side) – ................................... 56
7-8. Printed Wiring Board
– MB Board (Conductor Side) – ..................................... 57
7-9. Schematic Diagram – MB Board (1/14) – .................... 58
7-10. Schematic Diagram – MB Board (2/14) – .................... 59
7-11. Schematic Diagram – MB Board (3/14) – .................... 60
7-12. Schematic Diagram – MB Board (4/14) – .................... 61
7-13. Schematic Diagram – MB Board (5/14) – .................... 62
7-14. Schematic Diagram – MB Board (6/14) – .................... 63
7-15. Schematic Diagram – MB Board (7/14) – .................... 64
7-16. Schematic Diagram – MB Board (8/14) – .................... 65
7-17. Schematic Diagram – MB Board (9/14) – .................... 66
7-18. Schematic Diagram – MB Board (10/14) – .................. 67
7-19. Schematic Diagram – MB Board (11/14) – .................. 68
7-20. Schematic Diagram – MB Board (12/14) – .................. 69
7-21. Schematic Diagram – MB Board (13/14) – .................. 70
7-22. Schematic Diagram – MB Board (14/14) – .................. 71
7-23. Printed Wiring Board – DRIVER Board – .................... 72
7-10. Schematic Diagram – MB Board (2/14) – .................... 59
7-11. Schematic Diagram – MB Board (3/14) – .................... 60
7-12. Schematic Diagram – MB Board (4/14) – .................... 61
7-13. Schematic Diagram – MB Board (5/14) – .................... 62
7-14. Schematic Diagram – MB Board (6/14) – .................... 63
7-15. Schematic Diagram – MB Board (7/14) – .................... 64
7-16. Schematic Diagram – MB Board (8/14) – .................... 65
7-17. Schematic Diagram – MB Board (9/14) – .................... 66
7-18. Schematic Diagram – MB Board (10/14) – .................. 67
7-19. Schematic Diagram – MB Board (11/14) – .................. 68
7-20. Schematic Diagram – MB Board (12/14) – .................. 69
7-21. Schematic Diagram – MB Board (13/14) – .................. 70
7-22. Schematic Diagram – MB Board (14/14) – .................. 71
7-23. Printed Wiring Board – DRIVER Board – .................... 72
TABLE OF CONTENTS
7-24. Schematic Diagram – DRIVER Board – ....................... 73
7-25. Printed Wiring Boards
7-25. Printed Wiring Boards
– MOTOR/SWITCH Section – ....................................... 74
7-26. Schematic Diagram – MOTOR/SWITCH Section – .... 75
7-27. Printed Wiring Boards – SENSOR Section – ................ 76
7-28. Schematic Diagram – SENSOR Section – .................... 77
7-29. Printed Wiring Board
7-27. Printed Wiring Boards – SENSOR Section – ................ 76
7-28. Schematic Diagram – SENSOR Section – .................... 77
7-29. Printed Wiring Board
– AV Board (Component Side) – .................................... 78
7-30. Printed Wiring Board
– AV Board (Conductor Side) – ...................................... 79
7-31. Printed Wiring Board
– RS-232C Board – ......................................................... 80
7-32. Schematic Diagram – AV (1/3)/RS-232C Boards – ...... 81
7-33. Schematic Diagram – AV Board (2/3) – ........................ 82
7-34. Schematic Diagram – AV Board (3/3) – ........................ 83
7-35. Printed Wiring Board
7-33. Schematic Diagram – AV Board (2/3) – ........................ 82
7-34. Schematic Diagram – AV Board (3/3) – ........................ 83
7-35. Printed Wiring Board
– PANEL-L Board (Component Side) – ......................... 84
7-36. Printed Wiring Board
– PANEL-L Board (Conductor Side) – .......................... 85
7-37. Schematic Diagram – PANEL-L Board (1/2) – ............ 86
7-38. Schematic Diagram – PANEL-L Board (2/2) – ............ 87
7-39. Printed Wiring Boards – PANEL Section – .................. 88
7-40. Schematic Diagram – PANEL Section – ....................... 89
7-41. Printed Wiring Board – POWER Board – ..................... 90
7-42. Schematic Diagram – POWER Board – ........................ 91
7-43. IC Pin Function Description .......................................... 100
7-38. Schematic Diagram – PANEL-L Board (2/2) – ............ 87
7-39. Printed Wiring Boards – PANEL Section – .................. 88
7-40. Schematic Diagram – PANEL Section – ....................... 89
7-41. Printed Wiring Board – POWER Board – ..................... 90
7-42. Schematic Diagram – POWER Board – ........................ 91
7-43. IC Pin Function Description .......................................... 100
8.
EXPLODED VIEWS
8-1. Overall Section ............................................................... 124
8-2. Front Panel Section ........................................................ 125
8-3. Power Block Section ...................................................... 126
8-4. Table Section .................................................................. 127
8-5. Chassis Section .............................................................. 128
8-6. Base (Door) Section ....................................................... 129
8-7. CD/DVD Mechanism Deck Section-1
8-2. Front Panel Section ........................................................ 125
8-3. Power Block Section ...................................................... 126
8-4. Table Section .................................................................. 127
8-5. Chassis Section .............................................................. 128
8-6. Base (Door) Section ....................................................... 129
8-7. CD/DVD Mechanism Deck Section-1
(CDM62-DVBU26) ....................................................... 130
8-8. CD/DVD Mechanism Deck Section-2
(CDM62-DVBU26) ....................................................... 131
8-9. CD/DVD Mechanism Deck Section-3
(CDM62-DVBU26) ....................................................... 132
8-10. CD/DVD Mechanism Deck Section-4
(CDM62-DVBU26) ....................................................... 133
8-11. Optical Pick-up Section (DVBU26) .............................. 134
9.
ELECTRICAL PARTS LIST
.............................. 135
6
DVP-CX985V
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
NOTE OF REPLACING THE MB BOARD
When replacing the MB board, since the adjustment value is not
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
Procedure:
1. Set the test mode. (See page 23)
2. Press the [2] key of the remote commander, and set the “DRIVE
1. Set the test mode. (See page 23)
2. Press the [2] key of the remote commander, and set the “DRIVE
MANUAL OPERATION”. (See page 29)
3. Press the [6] key of the remote commander, and set the “2-6,
Memory Check”. (See page 32)
4. Press the [CLEAR] key of the remote commander, and initial-
ize Memory.
SETTING OR RELEASING THE FRONT COVER LOCK
Procedure:
1. Press the
1. Press the
I
/1
button to turn the power on.
2. Press two buttons of
x
and [OPEN/CLOSE] on the main unit
for 5 seconds or more.
Note:
The setting method and the releasing method are the same operation.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
– POWER Board (Conductor Side) –
CN201
13
1
CHECK OF POWER BOARD WITH THE POWER ON
It is possible to analyze the defect with only POWER board power
ON.
Procedure:
1. Set to power OFF state.
2. Remove the connector from CN201 on the POWER board.
3. Short between CN201 pin 1 (P-CONT) and CN201 pin qa
ON.
Procedure:
1. Set to power OFF state.
2. Remove the connector from CN201 on the POWER board.
3. Short between CN201 pin 1 (P-CONT) and CN201 pin qa
(EVER+3.3V) on the POWER board.
4. Turn the power ON.
5. Confirm that the voltage value of CN201 each pin on the
5. Confirm that the voltage value of CN201 each pin on the
POWER board satisfy following value .
CN201 Pin
Voltage Value
pin 2 (EVER–11V)
–11V
pin 3 (SW–11V)
–11V
pin 6, 7 (SW+11V)
+11V
pin 8 (SW+3.3V)
+3.3V
pin qa (EVER+3.3V)
+3.3V
pin qs (SW+5V)
+5V
pin qd (EVER+11V)
+11V
Ver. 1.2