DOWNLOAD Sony DVP-CX875P Service Manual ↓ Size: 24.17 MB | Pages: 127 in PDF or view online for FREE

Auto Adjustment

1. Auto TRK. Offset

2. Auto FCS Balance

3. Auto Focus Offset

4. Auto Focus Gain

5. Auto TRK.  Gain

6. Auto EQ.

7. Auto L.F. Offset

8. Auto Group Delay

SA.------ SI.-- EMG. 00

DVD SL 12 cm

On this screen, each item can be adjusted automatically. Select the
desired number 

[1]

 to 

[8]

 from the remote commander, and se-

lected item is adjusted automatically.

[1]

Auto TRK. Offset

Adjusts tracking offset.

[2]

Auto Focus Balance Adjusts focus balance.

[3]

Auto Focus Offset

Adjusts focus offset.

[4]

Auto Focus Gain

Adjusts focus gain.

[5]

Auto TRK. Gain

Adjusts track gain.

[6]

Auto EQ

[7]

Auto L.F. Offset

Adjusts loop filter offset.

[8]

Auto Group Delay

Display images are shown as follows, and all three screens are
able to switch.

EEPROM Data 1

-– DL -–

CD LCD

SL

L0

L1

Focus Gain

xx xx

xx

xx

xx

TRK. Gain

xx xx

xx

xx

xx

FCS Balance

xx xx

xx

xx

xx

Focus Bias

xx xx

xx

xx

xx

TRV. Offset

xx xx

xx

xx

xx

L.F. Offset

xx xx

xx

xx

xx

EQ. Boost

xx xx

xx

xx

xx

_ UP

: Last Data

  DOWN

: Next Data

  CLEAR : Default    Setpage.1/3

EEPROM Data 2

-– DL -–

CD LCD

SL

L0

L1

RF  Jitter

xx --

xx

xx

xx

RF  Level

xx --

xx

--

--

FE  Level

xx --

xx

--

--

FE Balance

xx --

xx

--

--

TRV.Level

xx --

xx

--

--

TE  Gain

xx xx

--

--

--

PI  Level

xx --

xx

xx

--

_ UP

: Prev Data

  DOWN

: Next Data

  CLEAR : Default    Setpage.2/3

← Fj (L0 → L1)

Focus jump reverse.
(Trk/Sled Servo OFF)

 

↑ Lj (L1 → L0)

Layer jump forward.
(Trk/Sled Servo ON)

 ↓ Lj (L0 → L1)

Layer jump reverse.
(Trk/Sled Servo ON)

Manual Adjustment:Up/Down

1. TRK. Offset

2. Focus Gain

3. TRK. Gain

4. Focus Offset

5. Focus Balance

6. L.F. Offset

7. Analog FRSW

8. PLL Dac Gain

9. EQ

BOOST

0. GD

ADJ

_

SA. ------ SI. -- EMG. 00

DVD SL 12cm           Jitter FF

On this screen, each item can be adjusted manually. Select the
desired number 

[1]

 to 

[0]

 from the remote commander, and cur-

rent setting for the selected item will be displayed, then increase
or decrease numeric value with  ↑ key or ↓ key. This value is
stored in the EEPROM. If CLV has been applied, the jitter is dis-
played for reference for the adjustment.

[1]

TRK. Offset

Adjusts tracking offset.

[2]

Focus Gain

Adjusts focus gain.

[3]

TRK. Gain

Adjusts track gain.

[4]

Focus Offset

Adjusts focus offset.

[5]

Focus Balance

Adjusts focus balance.

[6]

L.F. Offset

Adjusts loop filter offset.

[7]

Analog FRSW

Sets the shifting switch for analog feed-
back circuit.

[8]

PLL Dac Gain

Adjusts PLL D/A converter gain.

[9] EQ BOOST

Adjusts amount of boost of equalizer.

[0]

 GD ADJ

Adjusts amount of group delay

EEPROM Data 3

-– DL -–

CD LCD

SL

L0

L1

Analog FRSW

xx xx

xx

xx

xx

PLL Dac Gain

xx xx

xx

xx

xx

Mirror Time

xx xx

xx

xx

xx

   THR A&L: xx xx  xx/xx

xx

xx

_ UP

: Prev Data

  DOWN

: First Data

  CLEAR : Default    Setpage.3/3

On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the

[CLEAR]

  key, but be careful that they are not recoverable after

initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if 

[0]

 All is selected in the Drive Auto

Adjustment. In this case, default setting cannot be made.
Data of “THR A & L” on page 3/3 can not be changed if default
set is done.

On this test mode screen, selecting 

[7]

 enables the adjustment from

the front control panel such as disc loading. The following screen
appears.

Display when 

[7]

 is selected in the Drive Manual Operation

## 300 CHG MechaCon Menu 1 ##

ENTER

: Mecha Initial

PLAY

: Disc Load (Front)

STOP

: Disc UnLoad (Front)

OP/CL

: Door Open/Close

UP

: Unchuck (Front)

DOWN

: Chuck

RIGHT

: Loading (Front)

LEFT

: UnLoading (Front)

jog FOR : Table R Step Turn

jog PRV : Table L Step Turn

_

RETURN : Exit

[ENTER]

: Performs initialization of mechanism.

Mecha Initial

Because the mechanical initialization is per-
formed when the machine enters the Drive
Manual Operation mode, use this item when
an error such as adjustment error occurs.

[PLAY]

: Loads the disc from the chucking position of

Disc Load (Front)

the T. table toward inside the MD.
When the Disc Load is selected, a series of
operation starting from Unchucking – Load-
ing – Chucking is performed.

[STOP]

: Moves the disc from inside the MD to the T.

Disc Unload (Front) table.

When the Disc Unload is selected, a series
of operation starting from Unchucking –
Unloading – Chucking is performed.

[OP/CL]

: Opens and closes the door.

Door Open/Close

[UP]

: Un-chucks the MD block.

Un-chuck

[DOWN]

: Chucks the MD block.

Chuck

[RIGHT]

: Moves the disc from the un-chucked state

Loading (Front)

to the T. table then to the MD block.

[LEFT]

: Moves the disc from the un-chucked state

Unloading (Front)

to the MD block then to the T . table.

[jog FOR]

: Moves the T. table to the right in units of

Table R step Turn

the slit.
The T. table number is incremented in the
direction of positive (+) number.

[jog PRV]

: Moves the T. table to the left in units of the

Table L step Turn

slit.
The T. table number is decremented in the
direction of negative (–) number.

[RETURN]

: Returns to the Operation Menu.

Exit

On this test mode screen, selecting 

[8]

 enables the adjustment from

the rear panel such as disc loading. The following screen appears.

Display when 

[8]

 is selected in the Drive Manual Operation

## 300 CHG MechaCon Menu 2 ##

ENTER

: Mecha Initial

PLAY

: Disc Load (Rear)

STOP

: Disc UnLoad (Rear)

OP/CL

: Door Open/Close

UP

: UnChuck (Rear)

DOWN

: Chuck

RIGHT

: Loading (Rear)

LEFT

: UnLoading (Rear)

DISP

: Mecha Adjust

PAUSE

: TT Offset Debug

_

RETURN : Exit

Insertion and rejection of discs are performed from the rear panel.
All operations are the same as those of the 300 CHG MechaCon
Menu 1 except 

[DISP]

 and 

[PAUSE]

.

[DISP]

: When this item is selected, the machine enters

Mecha Adjust

the adjustment mode of the disc existence/
non-existence sensor. The following screen
appears.

[PAUSE]

: When this item is selected, load to the T.

TT Offset Debug

table is measured by changing the value of
the PWM control to the motor. Never at-
tempt to enter this mode. When this mode
is selected, the machine needs to perform
the Mecha Initial.

[LEFT]

: Determines the detection position of the T.

table by counting the number of slit’s tooth
of the T. table when the T. table is turned
counterclockwise by a full rotation.

Display when Turn Table Adjust Mode is selected in Mecha Ad-
just Mode.

## Turn Table Adjust Mode ##

JOGFWD    : Right 1 Step

JOGPRV    : Left 1 Step

DMSFWD    : Right 2 Step

DMSPRV    : Left 2 Step

ENTER

   : ENTER -> Exit

STEP

   : 12

RETURN : Exit

Performs the fine adjustment of the slit position of the T. table
using the Jog dial and the DMS (disc selection dial).

✫ After this operation, perform Disc Sensor Adjust (SEE 6-12).

[JOGFWD]

: Moves the T. table to the right by one pulse.

STEP +

[JOGPRV]

: Moves the T. table to the left by one pulse.

STEP –

[DMSFWD]

: Moves the T. table to the right by two pulses.

STEP ++

[DMSPRV]

: Moves the T. table to the left by two pulses.

STEP – –

[ENTER]

: Determines the adjustment values and the

set value.

STEP

: When the T. table is adjusted using the above

commands, the adjustment position during
each adjustment item is displayed. The ini-
tial value is set to 12.

Display when 

[PAUSE]

 is selected in the 300 CHG MechaCon

Menu 2

## Turn Table Offset Debug ##

No

|

On

|

off

1

|

xx

|

xx

2

|

xx

|

xx

3

|

xx

|

xx

4

|

xx

|

xx

5

|

xx

|

xx

PLAY

: Slow Turn (No.5)

STOP

: Turn Stop

PAUSE

: Change PWM

_

RETURN : Exit

[PLAY]

: Moves the T. table slowly.

[STOP]

: Stops movement of the T. table.

[PAUSE]

: Sets the PWM value in the order starting

from NO 

→ On→ Off.

Display when the Mecha Adjust is selected in the 300 CHG Mecha
Con Menu 2

## Mecha Adjust Mode ##

RIGHT

: Disc Sensor Adjust

LEFT

: TurnTable Adjust

TurnTable Data

: xx

Sensor sensiv

: xx

Sensor Posi RP

: xx

Sensor Posi RM

: xx

Sensor Posi LP

: xx

Sensor Posi LM

: xx _

RETURN : Exit

Turn Table Data

: Indicates the center position of the slit.

(Width of one slit = 24 pulses). The default
value is 12.

Sensor Sensiv

: Indicates sensitivity of the disc sensor. The

normal value is ranging form 0 to 15.

Sensor Posi RP

: These are not the important values.

Sensor Posi RM

: They indicate the position of the disc sensor

Sensor Posi LP

when the disc sensor monitors the disc when

Sensor Posi LM

rotating the T. table. Rx indicates the value
when the T. table is rotated clockwise and
Lx indicates  the value when the T. table is
rotated counterclockwise.

[RIGHT]

: Enters the sensitivity adjustment mode of

the disc sensor.

[LEFT]

: Adjusts finely the center position of the slit

in units of plus using the jog dial.

Display when Disc Sensor Adjust is selected in the 300 CHG Mecha
Con Menu 2

## Sensor Adjust Mode ##

DOWN

: Sensitivity Adjust

RIGHT

: Position Adjust R

LEFT

: Position Adjust L

RETURN : Exit

Before this operation, perform Turn Table Adjust (SEE 6-12) or
Mecha Initial (SEE 6-11).
You must perform 3 operations for Sensor Adjustment.

[DOWN]

 

→

[RIGHT]

→

[LEFT]

or LEFT

→ RIGHT

[DOWN]

: Performs the sensitivity adjustment of the

disc sensor by turning T. table for a full ro-
tation.

[RIGHT]

: Determines the detection position of the T.

table by counting the number of slit’s tooth
of the T. table when the T. table is turned
clockwise by a full rotation.

→

This mode is prepared for measurement of
the load to the T. table as described before.
Result of the measurement is not reflected
on adjustment.
After this mode is selected, Mecha Initial
must be performed.

When 

[3]

 is selected on this test mode screen, the machine enters

the mechanical aging mode. The following screen appears. Do not
use this mode.

### Mecha Aging ###

1. Please Select Aging Mode

2. All Mecha

: Random Aging Move

3. All Mecha

: +1 Move

4. All Mecha

: -1 Move

5. All Mecha

:  1 Disc Front

6. All Mecha

:  1 Disc Rear

7. TurnTable

: Random Move

8. TurnTable

: Half Move

9. Door Open/Close

Exit: RETURN

### EMG. History ###

Laser Hours

CD

xxh xxm

DVD

xxh xxm

 1.

00 00 00 00  00 00 00 00

00 00 00 00  00 00 00 00

 2.

00 00 00 00  00 00 00 00

00 00 00 00  00 00 00 00

_

Select: 1-9

Scroll: UP/DOWN

(1:Last EMG.)

 Exit: RETURN

On the Test Mode Menu screen, selecting 

[4]

 displays the infor-

mation such as servo emergency history. The history information
from last 1 up to 10 can be scrolled with  ↑ key or ↓ key. Also,
specific information can be displayed by directly entering that
number with ten keys.

The upper two lines display the laser ON total hours. Data below
minutes are omitted.

Clearing History Information

Clearing laser hours
Press 

[DISPLAY]

 and 

[CLEAR]

 keys in this order.

Both CD and DVD data are cleared.
Clearing emergency history
Press 

[TOP MENU]

 and 

[CLEAR]

 keys in this order.

Initializing set up data
Press 

[MENU]

 and 

[CLEAR]

 keys in this order.

The data have been initialized when “Set Up Initialized” mes-
sage is displayed. The EMG. History screen will be restored
soon.

## Version Information ##

IF con.

Ver:x.xxx(xxxx)

Group

xx

SYScon.

Ver:x.xxx(xxxx)

Model

xx

Region

0x

Servo DSP Ver: x.xxx

AVD ucode Ver: xxxxxxxx

OPT TYPE : x LASER

Exit: RETURN

The ROM version, region code, OPT type, etc. are displayed if

[5]

 is selected in the Test Mode Menu.

The parenthesized hexadecimal number in the version number field
indicates the checksum value of the ROM.

Note : After down loading ROM data, sometimes it happens that

checksum is not the same as that of ROM data which has
been down loaded. In such a case, go back to the menu
and select “0. Syscon Diagnosis”, then select “1. All” in
“2. Version”. If the result of this operation does not give
an agreement, it must be either Down Load error or ROM
error.

On the Test Mode Menu screen, selecting 

[6]

 displays color bars

for video level adjustment. During display of color bars, OSD dis-
appears but the menu screen will be restored if pressing any key.