Sony DVP-CX860 / DVP-CX870D (serv.man2) Service Manual ▷ View online
— 35 —
The loading guide (F), guide frame
(F) assy and disc start moving down
(arrow mark
(F) assy and disc start moving down
(arrow mark
1
) along with the cam
groove outside the control gear (F).
The disc returns to the original groove of
the turntable in the midst of descending.
the turntable in the midst of descending.
The portion
B
of the slider link moves
as shown in the arrow mark
1
around
the boss
A
as the pivot, along with the
cam groove inside the gear (F).
At the same time as the BU holder moves,
the chuck holder assy moves as shown by
the arrow mark
the chuck holder assy moves as shown by
the arrow mark
5
centering around the
portion
E
as the pivot, via the chuck driving
link that is fixed to the BU holder with screw.
The slider (U) that is connected with the portion
C
of
the slider link via slider link, and the slider (B) that is
connected with the slider (U) at the portion
connected with the slider (U) at the portion
D
, are
moved in the directions of the arrow marks
2
and
3
respectively.
The BU holder moves in the direction of the arrow
mark
mark
4
as it is interlocked with their respective cam
blocks of the slider (B) and slider (U).
FIG.26
FIG.27
FIG.20
PH262 on the CS-57 board detects from the
cam groove inside the control gear (F) that
the control gear (F) rotates by 180˚ that
stops the cam drive motor (dc motor).
cam groove inside the control gear (F) that
the control gear (F) rotates by 180˚ that
stops the cam drive motor (dc motor).
The chucking operation is performed without a disc.
Unloading is completed.
The loading guide (F) and guide frame
(F) assy move to the bottommost-end
and, at the same time the disk stopper
(front side) moves down. (arrow mark
(F) assy move to the bottommost-end
and, at the same time the disk stopper
(front side) moves down. (arrow mark
2
)
F
— 36 —
( FIG.26 )
Control gear (F)
Slider link
Slider (U)
Slider (B)
A
B
C
C
D
D
E
Chuck driving link
Chuck holder assy
BU holder
1
1
1
1
2
3
2
3
4
4
4
4
5
5
— 37 —
2
1
( FIG.27 )
Loading guide (F)
— 38 —
The portion
B
of the slider link moves as
shown in arrow mark
1
around the boss
of
A
as the pivot, along with the cam
groove inside the control gear (F).
At the same time when the BU holder moves, the chuck
holder assy moves as shown in the arrow mark
holder assy moves as shown in the arrow mark
5
around the portion
E
as the pivot, via the chuck
driving link that is fixed to the BU holder with screw.
The slider (U) that is connected by the portion
C
of the
slider link via the slider link, and the slider (B) that is
connected by the portion
connected by the portion
D
, move in the directions of
arrow marks
2
and
3
respectively
The BU holder moves in the direction of the
arrow mark
arrow mark
4
as it is interlocked with the
slider (B) and the slider (U)
FIG.28
FIG.29
FIG.30
FIG.31
Cam drive motor (dc motor) starts rotating.
Chucking is released.
Gear (A) (cam drive motor side) rotates in the direction of the arrow mark
1
.
The control gear (F) and control gear (R) start rotating in the direction
of the arrow mark
of the arrow mark
5
respectively (arrow marks
2
to
4
) via loading
gear (B) (dam drive motor side), chuck gear (C) and chuck gear (D).
The loading frame (R) assy and guide
frame (R) assy start moving upward
along with the cam groove outside the
control gear (R) as they are pushed
by the force of the extension spring.
(arrow mark
frame (R) assy start moving upward
along with the cam groove outside the
control gear (R) as they are pushed
by the force of the extension spring.
(arrow mark
1
) At the same time, the
disk stopper is released (arrow mark
2
).
G
The lower portion of a disc is pinched
by the groove at the tip of the loading
guide (R) and gets in contact with the
timing belt. (
by the groove at the tip of the loading
guide (R) and gets in contact with the
timing belt. (
1
)
Disc is supported by the three points that
are the tip of the loading guide (R),
the center guide and the portion
are the tip of the loading guide (R),
the center guide and the portion
A
of the
center guide assy. (arrow mark
2
)
3-7. Loading (Rear side)
Click on the first or last page to see other DVP-CX860 / DVP-CX870D (serv.man2) service manuals if exist.