Sony DVP-CX777ES Service Manual ▷ View online
29
DVP-CX777ES
4-5.
DRIVE MANUAL OPERATION
On the Test Mode Menu screen, select
[2]
, and the manual opera-
tion menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
on/off control and adjustment can be executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc type
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
7. Changer Manual Move
8. Changer Mecha Check
0. Disc Check Memory
_
Exit: RETURN
In using the Manual Operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
setting screen.
The Disc Type setting must be performed after a disc was
loaded.
The set Disc Type is cleared when the tray is opened.
The Disc Type setting must be performed after a disc was
loaded.
The set Disc Type is cleared when the tray is opened.
2. After power ON, if the Manual Operation was selected,
first perform “Reset SLED TILT” by opening 1. Disc Type
screen.
screen.
3. In case of an alarm, immediately press the
x
button to
stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote com-
mander)
mander)
I
/
1
: Power OFF
x
: Servo stop
A
(DISC EJECT) : Stop+Eject/Loading
O
(RETURN)
: Return to Operation Menu or Test Mode
Menu
>
,
.
: Transition between sub modes of menu
[1]
to
[9]
,
[0]
: Selection of menu and items
Cursor
[Q]
/
[q]
: Increase/Decrease in manually adjusted value
0. Disc Check Memory
Disc Check
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
_
On this screen, the mirror time is measured and written to the
EEPROM to check the disc type. First, set a DVD SL disc and
press
EEPROM to check the disc type. First, set a DVD SL disc and
press
[1]
, then set a CD disc and press
[2]
, and finally set a DVD
DL disc and press
[3]
. The measured mirror time is displayed re-
spectively.
The adjustment must be executed more than once after default
data were written.
From this screen, you can go to another mode by
pressing
The adjustment must be executed more than once after default
data were written.
From this screen, you can go to another mode by
pressing
>
or
.
key, but you cannot enter this mode from
another mode. You can enter this mode from the Operation Menu
screen only.
screen only.
1. Disc Type
Disc Type
1. Disc Type Auto Check
2. DVD SL 12cm
3. DVD DL 12cm
4. CD 12cm
5. LCD 12cm
6. DVD SL 8cm
7. DVD DL 8cm
8. CD 8cm
9. LCD 8cm
0. Reset SLED TILT
_
EMG. 00
0. Reset SLED TIL
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
[1]
automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
30
DVP-CX777ES
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
code display field will appear as shown below. These values are
displayed when PLL is locked.
Disc Type
1. Disc Type Auto Check
2. DVD SL 12cm
3. DVD DL 12cm
4. CD 12cm
5. LCD 12cm
6. DVD SL 8cm
7. DVD DL 8cm
8. CD 8cm
9. LCD 8cm
0. Reset SLED TILT
_
SA.------ SI.-- EMG.00
DVD SL 12cm
Jitter FF
Display when DVD SL 12cm disc was selected
Disc Type
1. Disc Type Auto Check
2. DVD SL 12cm
3. DVD DL 12cm
4. CD 12cm
5. LCD 12cm
6. DVD SL 8cm
7. DVD DL 8cm
8. CD 8cm
9. LCD 8cm
0. Reset SLED TILT
_
TC.--:--:-- EMG.00
CD 12cm
Jitter FF
Display when CD 12cm disc was selected
[0]
Reset SLED TILT : Reset the Sled and Tilt to initial position.
(Reset the Sled only to initial position be-
cause the Tilt mechanism is not available
in this model.)
cause the Tilt mechanism is not available
in this model.)
[1]
Disc Type Check : Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is correct.
If Disc Check Memory menu has not been
executed after EEPROM default setting,
the disc type cannot be judged. In this case,
return to the initial menu and make a check
for three types of discs (SL, DL, CD).
tom of screen, make sure that it is correct.
If Disc Check Memory menu has not been
executed after EEPROM default setting,
the disc type cannot be judged. In this case,
return to the initial menu and make a check
for three types of discs (SL, DL, CD).
[2]
to
[9]
: Select the loaded disc. The adjusted value
is written to the address of selected disc.
No further entry is necessary if
No further entry is necessary if
[1]
was
selected.
2. Servo Control
Servo Control
1. LD Off R. Sled FWD
2. SP Off L. Sled REV
3. Focus Off
4. TRK. Off
5. Sled Off
6. CLVA Off
7. FCS. Srch Off
0. Reset SLED TILT
_
SA.------ SI.-- EMG.00
DVD SL 12cm
Jitter FF
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
[0]
Reset SLED TILT : Reset the Sled and Tilt to initial position.
(Reset the Sled only to initial position be-
cause the Tilt mechanism is not available
in this model.)
cause the Tilt mechanism is not available
in this model.)
[1]
LD
: Turn ON/OFF the laser.
[2]
SP
: Turn ON/OFF the spindle.
[3]
Focus
: Search the focus and turn on the focus.
[4]
TRK.
: Turn ON/OFF the tracking servo.
[5]
Sled
: Turn ON/OFF the sled servo. When PLL
is not locked (cannot be locked), the sled
servo is not turned ON. The display keeps
OFF.)
servo is not turned ON. The display keeps
OFF.)
[6]
CLVA
: Turn ON/OFF normal servo of spindle
servo.
[7]
FCS. Srch
: Apply same voltage as that of focus search
to the focus drive to check the focus drive
system.
system.
5
Sled FWD
: Move the sled outward. Perform this op-
eration with the tracking servo turned off.
%
Sled REV
: Move the sled inward. Perform this opera-
tion with the tracking servo turned off.
31
DVP-CX777ES
3. Track/Layer Jump
Track/Layer Jump
1. 1Tj FWD R. Fj (L1->L0)
2. 1Tj REV L. Fj (L0->L1)
3. 2Tj FWD U. Lj (L1->L0)
4. 2Tj REV D. Lj (L0->L1)
5. NTj FWD
6. NTj REV
7. 500Tj FWD
8. 500Tj REV
9. 10k/20k FWD
0. 10k/20k REV
_
SA.------ SI.-- EMG.00
DVD DL 12cm
Jitter FF
On this screen, track jump, etc. can be performed. Only for the
DVD-DL, the focus jump and layer jump are displayed in the right
field.
DVD-DL, the focus jump and layer jump are displayed in the right
field.
[1]
1Tj FWD
: 1-track jump forward.
[2]
1Tj REV
: 1-track jump reverse.
[3]
2Tj FWD
: 2-track jump forward.
[4]
2Tj REV
: 2-track jump reverse.
[5]
NTj FWD
: N-track jump forward.
[6]
NTj REV
: N-track jump reverse.
[7]
500Tj FWD
: Fine search forward.
[8]
500Tj REV
: Fine search reverse.
[9]
10k/20k FWD : Direct search forward.
[0]
10k/20k REV : Direct search reverse.
– The following commands are valid for DVD-DL disc only –
5
(L1
t L0): Focus jump (Trk/Sled Servo OFF) forward.
%
(L0
t L1): Focus jump (Trk/Sled Servo OFF) reverse.
$
(L1
t L0): Layer jump (Trk/Sled Servo ON) forward.
4
(L0
t L1): Layer jump (Trk/Sled Servo ON) reverse.
4. Manual Adjustment
Manual Adjustment:Up/Down
1. TRK. Offset
2. Focus Gain
3. TRK. Gain
4. Focus Offset
5. Focus Balance
6. L.F. Offset
7. Analog FRSW
8. PLL Dac Gain
9. EQ BOOST
0. TRK. Balance
_
SA.------ SI.-- EMG. 00
DVD SL 12cm
Jitter FF
On this screen, each item can be adjusted manually. Select the
desired number
desired number
[1]
to
[0]
from the remote commander, and cur-
rent setting for the selected item will be displayed, then increase
or decrease numeric value with
or decrease numeric value with
$
key or
4
key. This value is
stored in the EEPROM. If CLV has been applied, the jitter is dis-
played for reference for the adjustment.
played for reference for the adjustment.
[1]
TRK. Offset
: Adjusts tracking offset.
[2]
Focus Gain
: Adjusts focus gain.
[3]
TRK. Gain
: Adjusts track gain.
[4]
Focus Offset
: Adjusts focus offset.
[5]
Focus Balance : Adjusts focus balance.
[6]
L.F. Offset
: Adjusts loop filter offset.
[7]
Analog FRSW : Sets select switch of analog feedback circuit.
[8]
PLL Dac Gain : Adjusts D/A converter gain of PLL.
[9]
EQ BOOST
: Adjusts boost amount of equalizer.
[0]
TRK. Balance : Adjusts tracking balance.
32
DVP-CX777ES
5. Auto Adjustment
Auto Adjustment
1. Auto TRK. Offset
2. Auto FCS Balance
3. Auto Focus Offset
4. Auto Focus Gain
5. Auto TRK. Gain
6. Auto EQ.
7. Auto L.F. Offset
8. Auto Group Delay
9. Auto TRK. Balance
_
SA.------ SI.-- EMG.00
DVD SL 12cm
Jitter FF
On this screen, each item can be adjusted automatically. Select the
desired number
desired number
[1]
to
[8]
from the remote commander, and se-
lected item is adjusted automatically.
[1]
Auto TRK. Offset
: Adjusts tracking offset.
[2]
Auto FCS Balance : Adjusts focus balance.
[3]
Auto Focus Offset
: Adjusts focus offset.
[4]
Auto Focus Gain
: Adjusts focus gain.
[5]
Auto TRK. Gain
: Adjusts track gain.
[6]
Auto EQ
: Adjusts EQ.
[7]
Auto L.F. Offset
: Adjusts loop filter offset.
[8]
Auto Group Delay : Adjusts amount of group delay.
[9]
Auto TRK. Balance : Adjusts tracking balance.
6. Memory Check
The display image is shown below and three screens in total can
be selected.
be selected.
EEPROM Data 1
-- DL --
CD LCD SL L0 L1
Focus Gain xx xx xx xx xx
TRK. Gain xx xx xx xx xx
FCS Balance xx xx xx xx xx
Focus Bias xx xx xx xx xx
TRV. Offset xx xx xx xx xx
L.F. Offset xx xx xx xx xx
EQ. Boost xx xx xx xx xx
_ UP : Last Data
DOWN : Next Data
CLEAR : Default Set
page.1/3
EEPROM Data 2
-- DL --
CD LCD SL L0 L1
RF Jitter xx -- xx xx xx
RF Level xx -- xx -- --
FE Level xx -- xx -- --
FE Balance xx -- xx -- --
TRV.Level xx -- xx -- --
TE Gain xx xx -- -- --
PI Level xx -- xx xx --
_ UP : Prev Data
DOWN : Next Data
CLEAR : Default Set
page.2/3
EEPROM Data 3
-- DL --
CD LCD SL L0 L1
Analog FRSW xx xx xx xx xx
PLL Dac Gain xx xx xx xx xx
Mirror Time xx xx xx xx xx
TRK. Balance xx xx xx xx xx
THR A&L : xx xx xx/xx xx xx
_ UP : Prev Data
DOWN : First Data
CLEAR : Default Set
page.3/3
On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the
are displayed. The adjusted data are initialized by pressing the
[CLEAR]
key, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if
[0]
All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.
“THR A&L” data on the third page cannot be changed if default
setting is once made.
“THR A&L” data on the third page cannot be changed if default
setting is once made.
Click on the first or last page to see other DVP-CX777ES service manuals if exist.