Sony DAV-DZ30 / HCD-DZ30 Service Manual ▷ View online
HCD-DZ30
53
Pin No.
Pin Name
I/O
Description
249
RFGND
—
Ground terminal
250
NC
O
EQ offset loop capacitance (not used (Open))
251
NC
O
EQ offset loop capacitance (not used (Open))
252
OSP
O
RF offset cancellation capacitor connecting
253
OSN
I
RF offset cancellation capacitor connecting
254
RFGC
O
RF offset loop capacitor connecting for DVD-ROM
255
IREF
I
Current reference input
256
AVDD3
—
Power Supply (+3.3V)
HCD-DZ30
54
MAIN BOARD IC501 M30622MEP-B20FPU0 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
DAMP_SCDT
O
Digital amp (IC3010, 3020, 3030) data output
2
DAMP_SHIFT
O
Digital amp (IC3010, 3020, 3030) data output
3
NO USE
O
Not used (Open)
4
SIRCS_IN
I
Sircs input
5
NO USE
O
Not used (Open)
6
NO USE
O
Not used (Open)
7
NO USE
O
Not used (Open)
8
BYTE
I
External data bus (Fixed to “L”)
9
CNVSS
I
Change processor mode (not used)
10
EN_A
I
Volume signal (A) input from ENCODER
11
EN_B
I
Volume signal (B) input from ENCODER
12
RESET
I
System reset signal input
13
XOUT
O
Crystal output for main clock (5MHz)
14
VSS
—
Ground terminal
15
XIN
I
Crystal input for main clock (5MHz)
16
VCC
—
Power supply (+3.3V)
17
NMI
I
Fixed to “H:+3.3V Line”
18
NO USE
O
Not used (Open)
19
A.CAL_OUT_LEVEL
I
OUT level detect for auto calibration (not used (Fixed to “L”))
20
AC_CUT
I
Detect AC-CUT (primary power off)
21
FL_CLK/LED_CLK
O
FL driver (IC802) clock output
22
NO USE
O
Not used (Open)
23
NO USE
O
Not used (Open)
24
FL_D_OUT/LED_DATA
O
FL driver (IC802) data output
25
NO USE
O
Not used (Open)
26
MIC_GAIN
O
MIC gain control output (not used (Open))
27
CDM_OPEN_SW
I
CDM open switch input
28
DC_CONT
O
A.CAL MIC DC Control (not used (Open))
29
CLINK_RX_IN
I
C-Link data input (not used)
30
CLINK_TX_OUT
O
C-Link data output (not used)
31
DVD_SID
O
SID data output to DVD RF (IC1101)
32
DVD_SOD
I
SOD data input from DVD RF (IC1101)
33
DVD_SCO
I
Clock signal input from DVD RF (IC1101)
34
DVD_XIFBUSY
O
IFBUSY signal output to DVD RF (IC1101)
35
NO USE
O
Not used (Open)
36
NO USE
O
Not used (Open)
37
DVDXIFCS
I
DVD RF (IC1101) chip select signal input
38
MTKRST
O
DVD RF (IC1101) reset signal output
39
P_CONT1
O
Power supply control signal 1 output
40
P_CONT2
O
Power supply control signal 2 output
41
P_CONT3
O
Power supply control signal 3 output
42
DRIVE_RST (EN)
O
Power driver (IC3100, 3150, 3200, 3250, 3300, 3400) reset signal output
43
DRIVE_OCP (DIAG)
I
Power driver (IC3100, 3150, 3200, 3250, 3300, 3400) shut down signal input
44
OVERFLOW1
I
Over fl ow detect input from digital amp F/C/S (IC3010, 3020, 3030)
45
OVERFLOW2
I
Over fl ow detect input from digital amp SW (IC3030)
46
WRITE CE
I
Flash Write CE (not used (Fixed to “H:+3.3V Line”))
47
DAMP_LATCH1
O
Digital amp (IC3010) chip select1 signal output
48
DAMP_LATCH2
O
Digital amp (IC3020) chip select1 signal output
49
DAMP_LATCH3
O
Digital amp (IC3030) chip select1 signal output
50
DAMP_INIT
O
Digital amp (IC3010, 3020, 3030) reset signal output
51
DAMP_SOFT_MUTE
O
Digital amp (IC3010, 3020, 3030) soft muting output
52
HP_SW
I
Headphone detect input (not used (Fixed to “L”))
53
HP_MUTE
O
Headphone muting (not used)
54
NO USE
O
Not used
55
NO USE
O
Not used
HCD-DZ30
55
Pin No.
Pin Name
I/O
Description
56
FL_STB
O
FL driver (IC802) chip select signal output
57
DC_DETECT
I
Speaker DC detect input
58
NO USE
O
Not used (Open)
59
NO USE
O
Not used (Open)
60
NO USE
O
Not used (Open)
61
NO USE
O
Not used (Open)
62
VCC
—
Power supply (+3.3V)
63
MIC/A.CAL_SW
I
MIC insert switch input (not used (Fixed to “L”))
64
VSS
—
Ground terminal
65
NO USE
O
Not used (Open)
66
NO USE
O
Not used (Open)
67
NO USE
O
Not used (Open)
68
TUNED
I
Tuner pack tuned input
69
ST_CLK
O
Tuner clock output
70
ST_DO
I
Tuner data input
71
ST_CE
O
Tuner chip enable output
72
ST_DI
O
Tuner data output
73
NO USE
O
Not used (Open)
74
KEY_INT
I
Wakeup from ECO mode by key input
75
RDS_CLK/NO USE
I
Tuner RDS clock input (AEP, UK only)
O
Not used (Open) (Except AEP, UK)
76
RDS_DATA/NO USE
I
Tuner RDS data input (AEP, UK only)
O
Not used (Open) (Except AEP, UK)
77
NO USE
O
Not used (Open)
78
TVSEL
O
TV control signal output
79
M_ST
O
LINK(Multi STEREO) control signal output
80
NO USE
O
Not used (Open)
81
ASEL3
O
Audio selector 3 signal output (not used (Open))
82
VSEL0
O
Video selector 0 signal output
83
VSEL1
O
Video selector 1 signal output (not used (Open))
84
ASEL0
O
Audio selector 0 signal output (not used (Open))
85
ASEL1
O
Audio selector 1 signal output
86
ASEL2
O
Audio selector 2 signal output (not used (Open))
87
VSEL2
O
Video selector 2 signal output (not used (Open))
88
VSEL3
O
Video selector 3 signal output (not used (Open))
89
NO USE
O
Not used (Open)
90
MONO/ST_DET
I
Front Jack MONO or STEREO detect input (not used (Fixed to “L”))
91
A.CALMICLEVEL
I
MIC level detect for auto calibration (not used (Fixed to “L”))
92
DESTINATION
I
Destination select input
93
MODEL
I
Model select input
94
KEY2
I
Key input 2
95
KEY1
I
Key input 1
96
AVSS
—
Ground terminal
97
KEY0
I
Key input 0
98
VREF
—
Reference Voltage (+3.3V)
99
VCC
—
Power supply (+3.3V)
100
NO USE
O
Not used (Open)
56
HCD-DZ30
front panel section
2
1
3
not supplied
not supplied
not supplied
#1
#1
#1
#3
#2
2
2
2
13
15
16
2
4
6
5
7
10
14
F901
12
11
not supplied
not supplied
not supplied
not supplied
TU901
DVD mechanism
deck section
(CDM85-DVBU102)
8
8
9
#1
"
#
#
"
SECTION 7
EXPLODED VIEWS
1
2-889-987-11 PANEL,
LOADING
2
3-077-331-21 +BV3
(3-CR)
3
4-232-478-31 FOOT
4
1-828-286-51 WIRE (FLAT TYPE) (5 CORE)
5
1-828-340-51 WIRE (FLAT TYPE) (15 CORE) (EXCEPT AEP,UK)
5
1-828-350-51 WIRE (FLAT TYPE) (17 CORE) (AEP,UK)
6
A-1251-054-A IO BOARD, COMPLETE
(E3,E12,E32,E87,AR,EA,MX,SP,TH)
6
A-1382-400-A IO BOARD, COMPLETE (AEP,UK)
6
A-1504-717-A IO BOARD, COMPLETE (RU)
7
1-828-333-51 WIRE (FLAT TYPE) (13 CORE)
8
3-363-099-22 SCREW (CASE 3 TP2)
9
2-892-574-31 CASE
10
3-077-331-11 +BV3
(3-CR)
0 11
1-777-071-83 CORD, POWER (EXCEPT UK,E87,AR,MX,TH)
0 11
1-829-387-11 CORD, POWER (AR)
0 11
1-829-627-11 CORD, POWER (E87,MX)
0 11
1-834-288-11 CORD, POWER (TH)
0 11
1-835-078-21 CORD, POWER (UK)
12
3-703-244-00 BUSHING (2104), CORD (EXCEPT E87,MX)
* 12
3-703-571-12 BUSHING (S) (4516), CORD (E87,MX)
9 13
A-1382-372-A MAIN BOARD, COMPLETE (for SERVICE) (AEP)
9 13
A-1382-388-A MAIN BOARD, COMPLETE (for SERVICE) (UK)
9 13
A-1382-405-A MAIN BOARD, COMPLETE (for SERVICE) (SP,TH)
9 13
A-1382-415-A MAIN BOARD, COMPLETE (for SERVICE)
(E87,MX)
9 13
A-1504-720-A MAIN BOARD, COMPLETE (for SERVICE) (RU)
9 13
A-1504-728-A MAIN BOARD, COMPLETE (for SERVICE) (E12)
9 13
A-1504-738-A MAIN BOARD, COMPLETE (for SERVICE) (E32)
9 13
A-1504-746-A MAIN BOARD, COMPLETE (for SERVICE) (AR)
9 13
A-1552-799-A MAIN BOARD, COMPLETE (for SERVICE) (E3,EA)
14
3-100-158-01 SHEET,
RADIATION
15
1-828-954-51 WIRE (FLAT TYPE) (9 CORE) (EXCEPT AEP,UK)
15
1-828-964-51 WIRE (FLAT TYPE) (11 CORE) (AEP,UK)
0 16
1-569-008-22 ADAPTOR, CONVERSION 2P (E32)
0 F901
1-533-311-12 FUSE, GLASS CYLINDRICAL (8A/125V) (E87,MX)
0 F901
1-576-233-51 FUSE (H.B.C.) (T6.3AL/250V)
(EXCEPT E32,E87,MX)
0 F901
1-576-300-51 FUSE (H.B.C.) (T8AL/250V) (E32)
TU901 1-693-724-11 TUNER (FM/AM) (ANTENNA) (AEP,UK)
TU901 1-693-725-11 TUNER (FM/AM) (ANTENNA) (RU)
TU901 1-693-761-21 TUNER (FM/AM) (ANTENNA) (EXCEPT AEP,UK,RU)
#1
TU901 1-693-761-21 TUNER (FM/AM) (ANTENNA) (EXCEPT AEP,UK,RU)
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
#2
7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3
#3
7-685-862-01 SCREW +BVTT 2.6X6 (S)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice.
vice.
Some delay should be anticipated when
ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Abbreviation
E3
E3
: 240V AC area in E model
E12
: 220-240V AC area in E model
E32
: 110-240V AC area in E model
E87
: Venezuelan model
AR :
Argentine
model
EA :
Saudi
Arabia
model
MX
: Mexican model
RU :
Russian
model
SP
: Singapore model
TH :
Thai
model
Note: If the wire (fl at type) was replaced,
fold it some as the wire (fl at type)
before replacement.
before replacement.
The components identifi ed by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
The components identifi ed by mark 9 con-
tain confi dential information.
Strictly follow the instructions whenever the
components are repaired and/or replaced.
tain confi dential information.
Strictly follow the instructions whenever the
components are repaired and/or replaced.
7-1. OVERALL SECTION
Ver. 1.4
Click on the first or last page to see other DAV-DZ30 / HCD-DZ30 service manuals if exist.