Sony DAV-DZ1000 / HCD-DZ1000 Service Manual ▷ View online
9
HCD-DZ1000
Precaution when installing a new OP unit /
Precaution before unsoldering the static electricity
prevention solder bridge
Precaution before unsoldering the static electricity
prevention solder bridge
When installing a new OP unit, be sure to connect the flexible
printed circuit board first of all before removing the static
electricity prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by
unsoldering after the flexible printed circuit board has already
been connected.
(Do not remove nor unsolder the solder bridge as long as the
OP unit is kept standalone.)
printed circuit board first of all before removing the static
electricity prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by
unsoldering after the flexible printed circuit board has already
been connected.
(Do not remove nor unsolder the solder bridge as long as the
OP unit is kept standalone.)
Note on replacement of C803, C802, L801,
and L802
and L802
Please fold in the directtion of the arrow and set up at
replacement of C803, C802, L801, and L802 on FL board.
L801
L802
C803
+
–
Attention of the direction at replacement
Please defend and install the direction of the below fig in the following parts on the POWER board.
LF902
LF901
PC901
R913
R912
R913
R912
PC903
POWER BOARD
PC902
L931
mark this side
OK
NG
mark this side
mark this side
10
HCD-DZ1000
Setting the DMPORT board (EXCEPT Mexican model)
The FFC 9P is the wire that ties CN201 (DMPORT board) to CN301 (IO-S-OUT board).
Please tuck the FFC 9P under the DMPORT board as shown Fig.-2.
Please tuck the FFC 9P under the DMPORT board as shown Fig.-2.
(Fig.-2)
8 mm
DMPORT
Board
Board
CN201
CN301
IO-S-OUT Board
FFC 9P
Tuck in
(Fig.-1)
IO-S-OUT Board
FFC 9P
CN201
(Fig.-1)
Note on C471 and C411 on JACK board
Bend C411 and keep the distance as shown. (Fig.-1)
Confirm C471 standing straightly. (Fig.-2)
Confirm C471 standing straightly. (Fig.-2)
Distance between the C411
top and bottom:
OK: 2 mm
top and bottom:
OK: 2 mm
±
1 mm
P-SW BOARD
JACK BOARD
JACK board
CN806
C411
J401
C471
C471
C411
J401
Fig.-2
Fig.-1
TERMINAL side
OK
NG
11
HCD-DZ1000
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Front panel
A "
/
1
(on/standby) (25)
B A
(open/close) (25)
C
Disc operation (25)
D
FUNCTION (25)
E
Front panel display (98)
F
(remote sensor) (8)
G
VOLUME control (25)
H
MIC 2 jack (60)
I
AUDIO IN/MIC 1/A.CAL MIC jack (14, 23,
60)
60)
J
Disc tray (25)
Rear panel
A
SPEAKER jacks (9)
B
DIR-TC1 slot for the WAHT-SD1 (23)
C
TV (AUDIO IN R/L) jacks (9)
D
DMPORT (DIGITAL MEDIA PORT) jack
(except for Mexican model) (23, 66)
(except for Mexican model) (23, 66)
E
MONITOR OUT (S VIDEO/VIDEO) jacks
(19)
(19)
F
AM terminal (9)
G
COAXIAL FM 75
Ω
jack (9)
H
SAT/CABLE (AUDIO IN R/L, VIDEO IN)
jacks (23)
jacks (23)
I
COMPONENT VIDEO OUT jacks (19)
J
SAT/CABLE (DIGITAL IN OPTICAL)
jack (23)
jack (23)
K
SAT/CABLE (DIGITAL IN COAXIAL)
jack (23)
jack (23)
L
HDMI OUT jack (19)
*
CAUTION
Please do not remove the screws before
installing the WAHT-SD1.
installing the WAHT-SD1.
COAXIAL
AM
FM75
(DVD ONLY)
OUT
DMPORT
FRONT R
CENTER
WOOFER
FRONT L
SUR R
SUR L
SPEAKER
SPEAKER
TV
SAT/CABLE
OPTICAL
COAXIAL
DIGITAL IN
COMPONENT VIDEO OUT
R
L
AUDIO IN
(DVD ONLY)
Y
P
B
/C
B
P
R
/C
R
SAT/CABLE
MONITOR OUT
VIDEO
(DVD ONLY)
S VIDEO
R
L
AUDIO IN
VIDEO IN
DIR-TC1
Screws
*
12
HCD-DZ1000
Front panel display
About the indications in the front panel display
A
Lights up when the HDMI OUT jack is
correctly connected to HDCP (high-
bandwidth digital content protection)
compliant device with HDMI or DVI
(digital visual interface) input. (19)
correctly connected to HDCP (high-
bandwidth digital content protection)
compliant device with HDMI or DVI
(digital visual interface) input. (19)
B
Lights up when the time information of
a title or chapter appears in the front
panel display. (DVD only) (42)
a title or chapter appears in the front
panel display. (DVD only) (42)
C
Lights up when the color system is set
to NTSC. (Asian, Australian, and Middle
Eastern models only)
Lights up when an NTSC disc is
loaded. (Russian models only)
to NTSC. (Asian, Australian, and Middle
Eastern models only)
Lights up when an NTSC disc is
loaded. (Russian models only)
D
Lights up when a station is received.
(Radio only) (55)
(Radio only) (55)
E
Stereo/Monaural effect (Radio only)
(56)
(56)
F
Lights up when the sleep timer is set.
(65)
(65)
G
Lights up when the movie or music
mode is selected. (28)
mode is selected. (28)
H
Playing status (DVD function only)
I
Lights up when the karaoke mode is
on. (60)
on. (60)
J
Current repeat mode (38)
K
Lights up when the child lock function
is set to on. (67)
is set to on. (67)
L
Lights up when the system outputs
progressive signals (DVD function
only). (21)
progressive signals (DVD function
only). (21)
M
Indicates the selected [SPEAKER
FORMATION]. (71)
FORMATION]. (71)
N
Lights up when Digital Cinema Sound
(DCS) is activated. (29)
(DCS) is activated. (29)
O
Current surround format (Except for
JPEG)
JPEG)
P
Lights up when the DYNAMIC BASS is
selected. (64)
selected. (64)
Q
Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, sound field, etc.
chapter, title, or track number, time
information, radio frequency, playing
status, sound field, etc.
Ver. 1.1
Click on the first or last page to see other DAV-DZ1000 / HCD-DZ1000 service manuals if exist.