DOWNLOAD Sony DAV-DS1000 / SS-IF1000 Service Manual ↓ Size: 921.78 KB | Pages: 10 in PDF or view online for FREE

AEP Model

UK Model

E Model

Australian Model

2004A16-1

© 2004.01

SS-IF1000 is the Front speaker
system in DAV-DS1000.

Speaker system

Bass reflex

Speaker unit

78 mm (3 

1

/

8

 inch) dia. cone type 

⋅  2, 25 mm (1 inch) dia. hard dome

Rated impedance

4 ohms

Dimensions (approx.)

140.5 

×

 1,250 

×

 108 mm (5 

5

/

8

 

×

 49 

1

/

4

 

×

4 

3

/

8

 inch)

 (w/h/d)

(Base: 300 

×

 300 mm (11 

7

/

8

 

×

11 

7

/

8

 inch))

Mass (approx.)

8.4 kg (18 lb 3 oz) 

Design and specifications are subject to change without notice.

2

0

0

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

• Keep the temperature of soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Keep your eyes 10cm or more away from the infrared laser unit.
Do not view directly the laser beam.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

DVD player :
DVX-DS1000

DVD player : DVX-DS1000

Sub woofer :
SA-WS1000

Sub woofer : SA-WS1000

Tuner :
ST-DS1000

Tuner : ST-DS1000

Front speaker :
SS-IF1000

Front speaker : SS-IF1000

Center speaker :
SS-CT1000

Center speaker : 
SS-CT1000

Rear speaker :
SS-IR1000

Rear speaker : SS-IR1000

Remote 
commander :
RM-SS1000/

SS1000B

Remote commander :
RM-SS1000/SS1000B

Units required for

operation

check

Unit. 
need to 
checking

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

a

*

1

*

1

*

2

*

1  Only the defective unit.  

*

2  Either one of them.

Units with 

a

 mark: The units that are required for the system operation check during repair service

However, there can be a case that some units of the system need to not be brought into repair shop depending on the unit. that became defective. 

• The units that are required for the system operation check during repair service

3

 Follow the disassembly procedure in the numerical order given.

4

 cap light (FR) assy

1

 net frame assy 

2

two screws
(+BVTP 3 

×

 10)

3

two screws
(PWH M3 )

net frame assy 

Caution:

To remove the net frame assy, heat the areas that are attached
 by the adhesive agent, to 40

°

C or 50

°

C with a hair-dryer. 

After heating up, remove it easily. 

Areas attached by 
adhesive agent

JIG for speaker remover
(J-2501-238-A)

6

connector 

     (CN103)

4

bracket (LED) board

7

TX LED board

5

claw

2

 cap (light)

1

three screws
(+BVTP 3 

×

 8)

3

screw
(+BVTP 3 

×

 10)

4

1

two screws
(+BVTP 3 

×

 10)

3

cover front

five claws

five claws

2

Slide ‘‘Cover Front’’ up to disengage the ten claws.