DOWNLOAD Sony DAV-C700 / DAV-C900 / HCD-C700 / HCD-C900 Service Manual ↓ Size: 13.59 MB | Pages: 108 in PDF or view online for FREE

3

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.

LEAKAGE
The AC leakage from any exposed metal part to earth Ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.

A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.

2.

A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.

3.

Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)

µF

Ω

Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.

Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be

 damaged by heat.

Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

 circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

 or unsoldering.

Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.

This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
 located on the rear exterior.

This caution
label is located
inside the unit.

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CHECKING  OF  OPERATIONS  WITH  REMOTE
COMMANDERS  OF  DIFFERENT  MODELS
Some of the signal of remote commander vary between generation
of player.
Between DAV-S400/S500/S800/C450/C700/C900 and DAV-S550/
S880/C770/C900, remote commander signal codes of
“FUNCTION”, “BAND”, “ST/MONO” and “MEMORY” are
different.
Take notice of the above when you check the operation with remote
commanders of different models.

NOTE OF REPLACING THE DVD BOARD
When replacing the DVD board, since the adjustment value is not
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.

Procedure:
1.Starting test mode. (See page 18)
2.Press the [2] key of the remote commander, and set the “DRIVE

MANUAL OPERATION”. (See page 24)

3.Press the [6] key of the remote commander, and set the “6. Memory

Check”. (See page 26)

4.Press the [CLEAR] key of the remote commander, and initialize

Memory.

4

·········································································· 5

································································ 7

···································································· 18

·································· 28

······································································ 30

5-1. Block Diagrams

– RF/Servo, Video Section – ······································· 32
– CPU Section – ·························································· 33
– Power Section – ························································ 34

5-2. Printed Wiring Board  – RF Section – ························· 35
5-3. Schematic Diagram  – RF Section – ··························· 36
5-4. Printed Wiring Board  – DVD Section (Side A) – ······· 37
5-5. Printed Wiring Board  – DVD (Side B) Section – ······· 38
5-6. Schematic Diagram  – DVD Section (1/9) – ··············· 39
5-7. Schematic Diagram  – DVD Section (2/9) – ··············· 40
5-8. Schematic Diagram  – DVD Section (3/9) – ··············· 41
5-9. Schematic Diagram  – DVD Section (4/9) – ··············· 42
5-10. Schematic Diagram  – DVD Section (5/9) – ··············· 43
5-11. Schematic Diagram  – DVD Section (6/9) – ··············· 44
5-12. Schematic Diagram  – DVD Section (7/9) – ··············· 45
5-13. Schematic Diagram  – DVD Section (8/9) – ··············· 46
5-14. Schematic Diagram  – DVD Section (9/9) – ··············· 47
5-15. Printed Wiring Board  – AMP Section (Side A) – ······· 48
5-16. Printed Wiring Board  – AMP Section (Side B) – ······· 49
5-17. Schematic Diagram  – AMP Section (1/2) – ··············· 50
5-18. Schematic Diagram  – AMP Section (2/2) – ··············· 51
5-19. Printed Wiring Board  – I/O Section – ························ 52
5-20. Schematic Diagram  – I/O Section (1/2) – ·················· 53
5-21. Schematic Diagram  – I/O Section (2/2) – ·················· 54
5-22. Printed Wiring Board  – Front Section – ····················· 55
5-23. Schematic Diagram  – Front Section – ························ 56
5-24. Printed Wiring Board  – SW Section – ························ 57
5-25. Schematic Diagram  – SW Section – ·························· 58
5-26. Printed Wiring Board  – CDM Section – ···················· 59
5-27. Schematic Diagram  – CDM Section – ······················· 60
5-28. Printed Wiring Board  – Power Section (Side A) – ····· 61
5-29. Printed Wiring Board  – Power Section (Side B) – ····· 62
5-30. Schematic Diagram  – Power Section – ······················ 63
5-31. IC Block Diagrams ······················································ 64
5-32. IC Pin Function Description ········································ 67

6-1. Case (Top) Section ······················································ 77
6-2. Chassis Section ···························································· 78
6-3. Front Panel Section ····················································· 79
6-4. Overall Section (CDM53K-DVBU7) ·························· 80
6-5. Chassis (Mold) Assembly Section

(CDM53K-DVBU7) ···················································· 81

6-6. Chassis Section (CDM53K-DVBU7) ·························· 82
6-7. Stocker (240) Overall, Optical Pick-up Section

(CDM53K-DVBU7) ···················································· 83

······································· 84

5

This section is extracted
from instruction manual.

For more information, refer to the pages indicated in parentheses.

1 POWER switch/indicator (32)
2

3

DISC 1 (play) /A  (open/close)-DISC 5
(play) / A (open/close) (32)
Front panel display (12)

4

./> PREV/NEXT, PRESET +/–
(30, 33)

5

H (play) (32)

6

X (pause) (33)

7

x (stop) (32)

8 PHONES jack (32)
9 VOLUME control (32)
q; SOUND FIELD +/– (49)
qa DISPLAY (49, 62)
qs BAND (30)
qd FUNCTION (61)
qf

 (remote sensor) (18)

qg Disc tray (32)

1 AM antenna (21)
2 VIDEO 1 jacks (23)
3 VIDEO 2 jacks (23)
4 DIGITAL IN (OPTICAL) jack (24)
5 DIGITAL OUT (OPTICAL) jack

6 MONITOR OUT (VIDEO/S VIDEO)

jacks (23)

7 COMPONENT VIDEO OUT jacks (23)
8 SPEAKER jacks (19)
9 FM 75

Ω

 COAXIAL antenna jack (22)

V I D E O   O U T

A U D I O   OUT

V I D E O  I N

A U D I O  I N

L

R

V I D E O  I N

A U D I O  I N

L

R

O P T I C A L

D I G I T A L

I N

D I G I T A L

( C D   O N L Y )

V I D E O

S V I D E O  

( DVD ONLY)

Y

P

B

/ B - Y

P

R

/ R - Y

FRONT   R

FRONT   L

CENTER

S P E A K E R

REAR   R

REAR   L

WOOFER

COAXIAL

AM

FM

75

6

1

2

3

4

5

6

7

>10

10/0

8

9

1 TV [/1 (on/standby) (60)
2 OPEN/CLOSE (32)
3 NAME (63)
4 STEREO/MONO (62)
5 MEMORY (30)
6 CLEAR (37)

7 PLAY MODE (37)
8 AUDIO (47)
9 ANGLE (52)
q; SUBTITLE (53)
qa VOL +/– (62)
qs

./> PREV/NEXT, TV/PRESET
+/– (30, 33)

qd

H PLAY/SELECT (32)

qf TITLE (35)
qg DVD DISPLAY (37)
qh C/X/x/c/ENTER (26)
qj DVD SETUP (56)
qk

[/1 (on/standby) (32)

ql DISC SKIP (32)
w; TV/VIDEO (60)
wa REPEAT (40)
ws MUTING (33)
wd TIME (45)
wf FUNCTION (61)

wg BAND (30)
wh Number buttons (35)
wj SOUND FIELD (49)
wk DISPLAY (49, 62)
wl ENTER
e; CONTROL DVD/TV switch (60)

ea

m/M/

/

 SLOW, TUNING +/–

(30, 41)

es

x STOP (32)

ed

X PAUSE (33)

ef DVD MENU (35)
eg

O RETURN (36)

eh AMP MENU (26)

This remote control glows in the dark. However,
before glowing, the remote must be exposed to light
for awhile.