Sony BDP-S7200 Service Manual ▷ View online
BDP-S7200
6-9
6-7. Drive fl owchart
Optical Block Unit (BU) IOP check flow (zz) ~ [Before BU Replacem
Optical Block unit (BU) OP Data Write Flow (yy) ~ [After BU/MB Replacement]
nt]
e
BDP-S6200/BX620
can play the BD-disc
can play the BD-disc
BLX-104
Check Drive Power Supply
Check
PS301, PS302
Replace PS when open
Check / replace the FFC cable, then check
BDP-
S6200/BX620
operates normally
OPT-005 FFC cable (1-839-540-11) @
OPT-1003 FFC cable (1-848-104-11)
OPT-1003 FFC cable (1-848-104-11)
Check the Optical Block Unit (BU) by
service mode. (Flowchart zz)
BU IOP is OK?
Replace the Optical Block Unit (BU)
Optical Block Unit (BU) replace
(Flowchart yy)
OK
Optical Block or BU no problem
DVD: HLX-513
CD: HLX-A1
CD: HLX-A1
NO
YES
NO
YES
YES
NO
NO
YES
NO
YES
Enter Service Mode
Press
<OPEN/CLOSE>., <PLAY>,<STOP>
and plug in AC Power
Inside *Service Mode Menu
Select [8] Drive
Inside *Drive
Select [7] OP Check Menu
Inside *OP Check Menu
Select [3] dIOP then press 'ENTER'
Specification dIOP
BD:
6mA
DVD, CD:
9mA
IOP out of specification need BU
replacement
Optical Block Unit (BU) replace
(Flowchart yy)
AC Power OFF
NO
YES
Remove the defective BU from Loading
Assy and also remove BU insulator (4pcs)
Unpack new BU and take OP Data
Barcode photo by camera
Assemble BU with Insulators to Loading
Assy (tighten screw with 2kgf)
Decode the OP Data Barcode photo using
BDPRdec.exe
and save the test data to
USB memory
(File Name: BuData.txt)
Enter Service Mode and insert USB
memory to USB connector
Select [8] Drive -->
Select [1] Drive OP data Write
Press ENTER
After Finishing ReWrite OP data
--> Turn AC Power OFF
And confirm dIOP by select [7] OP Check
Menu to verify IOP in specification
IOP in specification --> Turn AC Power
OFF
Turn Power ON and check playback
performance using BD, DVD and CD
BLX-104
DVD: HLX-513
CD: HLX-A1
CD: HLX-A1
The following cases need OP Data Write:
(1) Replace BU (MB is original)
(2) Replace MB (BU is original)
(3) Replace both BU and MB
(2) Replace MB (BU is original)
(3) Replace both BU and MB
JIG requirement
Digital camera (with macro mode)
Barcode decoder (BDPRdec.exe)
installed in jig
PC's (jig purpose)
USB memory
ESD free work bench
Barcode decoder (BDPRdec.exe)
installed in jig
PC's (jig purpose)
USB memory
ESD free work bench
-
+
-
+
C888 Pin 1: 5V
C889 Pin 1: 12V
Select Mode : 1 or 2
on:
ti
Explana
t
e 1: BDV se
Mod
Mode 2: BDP set
Mode 2: BDP set
BDP-S6200/BX620
can play the DVD/CD-disc
can play the DVD/CD-disc
BDP-S7200
6-10
6-8. Ethernet fl owchart
Wifi fl owchart
Cannot connect with the network, cannot
update through the network
update through the network
Is the LAN cable plugged in properly?
No
Plug in the LAN cable firmly
Yes
Is the LED of the hub router lit?
(LINK LED)
(LINK LED)
No
Is power supplied to the MB board?
No
To Power Supply (System) flowchart
Yes
Are the network settings of the menu
correct?
correct?
No
Make the correct network settings.
Yes
START
Retry connection
Connection
Success?
Success?
Change MB board
END
Wireless setup fail.
Check SW5V at Wi
Į Module
pin 5
To power supply
Ňow chart
Check usb harness connec
Ɵon
is OK?
SW5V supplied OK
Plug in harness properly
NO
NO
YES
YES
Repeat wireless setup
Can establish
Wi-Fi Connec
Ɵon?
Change Main board
NO
END
START
YES
BDP-S7200
6-12E
6-9 USB (Front) Device Flow/USB (Rear) Device Flowchart
USB device is not recognized
Insert the USB device again.
Is it recognized when the power is
turned OFF and then ON again?
Is it recognized when the power is
turned OFF and then ON again?
No
Is 5V present at CN201
(FR-1304)
board
) pin1?
No
Is 5V present at
CN402
(MB board) Pin 5 or pin 6?
No
Is 5V present at
(MB board)?
No
Power supply IC310 (MB board -
defective
defective
Ye
s
Y
s
e
Yes
Poor contact of the USB device
Defective FFC between the IF
board and the MB board.
board and the MB board.
Does replacing IC501(MB board)
improve the symptoms?
improve the symptoms?
No
Replace the MB board
Yes
Yes
Replace the FFC between the
MB board and the IF board.
Do the symptoms improve?
MB board and the IF board.
Do the symptoms improve?
No
Replace the MB board.
IC 601 (MB board) defective
Yes
Defective FFC between the IF
board and the MB board
board and the MB board
IC501
Pin 5 /6/7?
7-1
BDP-S7200
Ref. No.
Part No.
Description
Remark
* 1
X-2589-328-1
PANEL ASSY, TOP
BDP-S7200:Except US
* 1
X-2589-425-1
PANEL ASSY, TOP
BDP-S7200:US
2
X-2589-329-1
TRAY ASSY, COVER
The components identifi ed by mark
or dotted
line with mark
are critical for safety.
Replace only with part number specifi ed.
Les composants iden tifi és par une marque
sont critiquens pour la sécurité.
Ne les remplace r que par une pièce portant le
numéro spécifi é.
The components identifi ed by mark contain
confi dential information.
Strictly follow the instructions whenever the
components are repaired and/or replaced.
Les composants identifi és par la marque con-
tiennent des informations confi dentielles.
Suivre scrupuleusement les instructions
chaque fois qu’un composant est remplacé et
/ ou réparé.
7-1.
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they may
have some difference from the original one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
• Items marked “*” are not stocked since they are sel-
dom required for routine service. Some delay should
be anticipated when ordering these items.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Accessories and packing materials are given in the
last of the electrical parts list.
7-1-1 CASE SECTION
ns: not supplied
Abbreviation :
AEP : AEP Model
SP : Singapore Model
TH : Thailand Model
TW : Taiwan Region Model
UK : AEP Model
US : US Model
SECTION 7
REPAIR PARTS LIST
1
2
3-215-529-02 EMBLEM (NO.5), SONY
3
3
3
Click on the first or last page to see other BDP-S7200 service manuals if exist.