Sony BDP-S2100 Service Manual ▷ View online
1-6-2. Front panel assemble caution.
1-6-2.1 Upper case placed slightly vertical with stopper at front panel both left and right
1-6-2.2 The stopper will used has rotate guide when upper case moved downward from this position.
1-6-2.2 The stopper will used has rotate guide when upper case moved downward from this position.
1-6-2.3 After upper case placed in horizontal position, ensure that there gap at highlighted area
1-6-2.4 This gap means upper case hook at behind of chassis slot. Thus, in next step the hook can be insert in the slot.
1-6-2.5 If there is no gap means the hook is on top of the slot and it will never enter the slot.
1-6-2.4 This gap means upper case hook at behind of chassis slot. Thus, in next step the hook can be insert in the slot.
1-6-2.5 If there is no gap means the hook is on top of the slot and it will never enter the slot.
1-6-2.6 Push at both side surface of upper case.
1-6-2.7 While pushing at the both surface, pull the upper case toward.
1-6-2.7 While pushing at the both surface, pull the upper case toward.
Stopper front panel right side.
^ƚŽƉƉĞƌĨƌŽŶƚƉĂŶĞůůĞŌƐŝĚĞ͘
1
6
2
6
1) Push jig to shown
ĚŝƌĞĐƟŽŶ͕ if *jig CANNOT go means OK
NG CONDITION
7
7
NG CONDITION
1) Push jig to shown
ĚŝƌĞĐƟŽŶ͕ if *jig CAN go means NG
2) Slot at chassis CAN be seen from
ďŽƩŽŵ͘
OK CONDITION
1
2
ΎũŝŐǁŝĚƚŚ͗Ϭ͘ϱŵŵ
ΎũŝŐǁŝĚƚŚ͗Ϭ͘ϱŵŵ
E
1-22
BDP-S2100
2-1
BDP-S2100
3
Insert a clip in the hole of a drive
to
open a tray.
1 Three screws (Black)
+BTP 3X8 TYPE2 N-S
WLJKWHQLQJWRUTXH WRNJIFP
WLJKWHQLQJWRUTXH WRNJIFP
Tray
5
Tray cover assy
4
2
Upper case
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. UPPER CASE AND TRAY COVER ASSY
SET
2-2 UPPER CASE AND
TRAY COVER ASSY
(Page 2-1)
2-3 FRONT PANEL,
FR-1001 boards,
and WLAN Module
(Page 2-2)
2-4 SWITCHING REGULATOR
AND MB-1007 BOARD
(Page 2-2)
2-5 BD DRIVE
(Page 2-3)
2-2
BDP-S2100
2-3. FRONT PANEL, FR-1001 BOARD AND WLAN MODULE
2-4. SWITCHING REGULATOR AND MB-1007 BOARD
*Note : Hold upward hook No. 3 when unhook no 4 and 5.
Five hook
1
Two screws +BV3(3-CR)
WLJKWHQLQJWRUTXH WRNJIFP
WLJKWHQLQJWRUTXH WRNJIFP
Front Panel
One screw +BV3(3-CR)
WLJKWHQLQJWRUTXH WRNJIFP
9
8
Earth plate
FR-1001 Board
Flexibleflat cable (FIM-1001)
(CN701)
WLAN Module
Harness (USB-1001)
(CNxxx)
2
1
2
3
5
4
3
4
6
5
7
Flexible flat cable (SPD-005)
(CN660)
Flexible flat cable (LDG-1001)
(CN670)
Flexible flat cable (OPT-1001)
(CN501)
Harness (USB-1001)
(CN390)
9
8
7
6
Three screws +BV3(3-CR)
WLJKWHQLQJWRUTXH WRNJIFP
5
Harness (PM-1001)
(CN201)
(CN201)
Flexible flat cable (FIM-1001)
(CN303)
(CN303)
10
14
MB-1007 board
Two screw +B 3X3
WLJKWHQLQJWRUTXH WRNJIFP
4
12
One screw +BV3(3-CR)
WLJKWHQLQJWRUTXH WRNJIFP
1
Switching regulator
2
PS insulator
3
2-3
BDP-S2100
2-5. BD DRIVE
2-6. CIRCUIT BOARDS LOCATION
Switching regulator
WLAN Module
FR-1001 Board
MB-1007 board
BDdrive 5
Two screws +BV3(3-CR)
WLJKWHQLQJWRUTXH WRNJIFP
WLJKWHQLQJWRUTXH WRNJIFP
Loading flexible flat cable (LDG-1001)
(CN670)
Spindle flexible flat cable (SPD-005)
(CN660)
Optical flexible flat cable (OPT-1001)
(CN501)
(CN501)
1
4
3
2
Chasis
6
E
Click on the first or last page to see other BDP-S2100 service manuals if exist.